Bosch MCM3501M MultiTalent 3 Food Processor Instruction Manual

MCM3501M MultiTalent 3 Food Processor
Instruction Manual

For your safety

Before use, read these instructions carefully in order to become familiar with important safety and operating instructions for this appliance. If the instructions for the correct use of the appliance are not observed, the manufacturer’s liability for any resulting damage will be excluded.
This appliance is intended for domestic use only. Use the appliance for processing normal amounts of food for the household; see “Recipes / Ingredients / Processing” section. This appliance is suitable for mixing, kneading, beating, cutting, and shredding food. Other applications are possible if the accessories approved by the manufacturer are used. It must not be used for processing other objects or substances.
Use the appliance with original accessories only.
Please keep the operating instructions in a safe place. If passing on the appliance to a third party, always include the operating instructions.
Only use the appliance indoors at room temperature and up to 2000 m above sea level.
General safety instructions
Risk of electric shock
The appliance must not be used by children.
The appliance and its power cord must be kept away from children.
Appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and if they understand the hazards involved.
Children shall not play with the appliance.
Connect and operate the appliance only in accordance with the specifications on the rating plate. Do not use the appliance if the power cord and/or appliance are damaged.
Before replacing accessories or additional parts, which move during operation, switch off the appliance and disconnect from the power supply. Always disconnect the appliance from the supply if it is left unattended and before assembling, disassembling, or cleaning.
Do not place the power cord over sharp edges or hot surfaces. To prevent injury, a damaged power cord must be replaced by the manufacturer or his customer service or a similarly qualified person. Only our customer service may repair the appliance.
Safety instructions for this appliance
Risk of injury
Risk of electric shock
If the power is interrupted, the appliance remains switched on and restarts when the power is restored.
Never immerse the base unit in liquids or place it under running water and do not clean in the dishwasher.
Before rectifying a fault, pull out the mains plug.
Risk of injury from the rotating tools!
While the appliance is operating, never place fingers in the mixing bowl. Always use the pusher for adding ingredients.
After switching off, the drive continues running for a short time.
Change tools only when the drive is at a standstill.
Risk of injury from sharp blades/rotating drive!
Never reach into the attached blender jug!
Do not remove/attach the blender jug until the drive has stopped. Do not remove/attach the universal cutter jug until the drive has stopped.
Risk of injury from sharp blades!
Do not touch blades of the universal blade with bare hands. When not in use, always store the universal blade in the blade guard. Clean them with a brush.
Do not grip the sharp blades or edges of the cutting discs. Grip the discs by the plastic part in the center only!
Do not place fingers in the feed tube. Only use the pusher when adding more ingredients. Do not touch the blades of the blade insert with bare hands. Clean them with a brush. Risk of scalding!
If processing hot liquids, steam escapes through the funnel in the lid. Add a max. 0,4 liters of hot or frothing liquid.
Risk of injury!
Never assemble accessories on the base unit.
Explanation of the symbols on the appliance or accessory

	Caution! Rotating tools. Do not place fingers in the feed tube.
	Lock blade inserts in the blender or universal cutter jug.
	Remove blade insert from the blender or universal cutter jug.
	Blade insert with blender/cutting blade
	Blade insert with a grinding blade

Congratulations on the purchase of your new Bosch appliance. You can find further information about our products on our website.

Overview

Please fold out the illustrated pages. Fig. A
Base unit

Rotary switch  
0/off = Stop 
M = Instantaneous switching at  maximum speed, hold switch for requiredblending duration.
Settings 1–2, Operating speed:
1 = low speed – slow,
2 = high speed – fast.
Drive
Cord store
Bowl
Tool holder
Tools*
a Universal blade with a blade guard
b Kneading hook
c Beating disc
Cutting discs*
a Slicing reversible disc – thick/thin
b Shredding reversible disc –   coarse/fine
c Reversible slicing/shredding disc
Lid
a Filler opening
b Pusher
Accessories*
Blade insert with blender/cutting blade and seal
Blade insert with grinding blade and seal
Universal cutter jug
Blender jug
Lid for blender
a Filler opening
b Funnelshaped stopper
*  for some models

With the universal cutter use the appliance at  full power (according to the recipe). You can  find the recipe on the illustrated pages (Fig. F).
If the universal cutter is not included with  the hand blender, it can be ordered from  customer service (order no. 12005833).

Operation

Before operating the appliance and accessories for the first time, clean thoroughly; see  “Cleaning and servicing”.
Preparation

Place the base unit on a smooth, clean  surface.
Pull the cable out of the base unit to the  required length.

Important information
– Use only the rotary switch to switch the  appliance on or off.
– Never switch the appliance off by rotating  the bowl, the blender or a tool.
– Do not switch the appliance on unless  tools or accessories have been completely  attached.
Bowl with accessories/tools
Risk of injury from the rotating tools!
While the appliance is operating, never place  fingers in the mixing bowl. Always use the  pusher for adding ingredients. After switching  off, the drive continues running for a short
time. Change tools only when the drive is at  a standstill.
Warning!
When working with the bowl, the appliance cannot be switched on until the bowl has been attached and the lid has been attached and screwed on tight.
Universal blade
for cutting, mincing and mixing. Risk of injury from sharp blades!
Do not touch blades of the universal blade with bare hands. When not in use, always store the universal blade in the blade guard. Grip the universal blade by the edge of the plastic handle only.
Kneading hook
for kneading dough and mixing-in ingredients that ought not to be cut (e.g. raisins and chocolate chips).Beating disc
for cream, egg white, and mayonnaise.
Fig. B

Attach the bowl (arrow on a bowl on dot on the appliance: ) and rotate as far as possible in a clockwise direction ().
Insert the tool holder into the bowl.
Insert a universal blade, whisking disc, or kneading hook into the tool holder and release.

Note the position of the tools when inserting them! Press tools all the way down.
Warning! Do not add ingredients until the tools have been inserted.

Add ingredients.
Attach the lid with a pusher (match the arrow on the lid on the dot on the bow and rotate in a clockwise direction (). The lid lug must be located fully in the slot in the bowl handle.
Insert the mains plug.
Set the rotary switch to the desired setting.
To add more ingredients, set the rotary switch to 0/off.
Remove the pusher and add ingredients through the feed tube. A pusher can be used as a measuring cup.

Cutting discs
Risk of injury from sharp blades!
Do not grip the sharp blades or edges of the cutting discs. Grip the discs by the plastic part in the center only! Do not place fingers in the feed tube. Only use the pusher when adding more ingredients.
Slicing reversible disc —thick/thin
for slicing fruit and vegetables. The process at setting 1.
Identification of the reversible slicing disc: “grob” for the thick cutting side, “fein” for the thin cutting sideWarning! The reversible slicing disc is not suitable for slicing hard cheese, bread, rolls, or chocolate. Slice boiled, waxy potatoes only when they are cold.
Shredding reversible disc — coarse/fine for shredding vegetables, fruit, and cheese, except for hard cheese (e.g. Parmesan).
The process at setting 1.
Designation of the reversible shredding disc:
“2” for the coarse shredding side and
“4” for the fine shredding side
Warning! The reversible shredding disc is not suitable for shredding nuts. Shred soft cheese with the coarse side only at setting 2.
Reversible slicing/shredding disc for slicing and shredding fruit, vegetables, and cheese. The process at setting 2.
Note: Do not process any hard foods using the slicing/grating reversible disc as this may blunt the blade. Use the slicing reversible disc (thick/thin) for this purpose.
Fig. C

Attach the bowl (arrow on a bowl on dot on the appliance ) and rotate as far as possible in a clockwise direction ()
Insert the tool holder into the bowl.
Depending on the required use:
Place cutting disc on the tool holder. Turn required slicing/shredding side face up. Place the disc on the disc holder so that the drivers on the tool holder grip the opening in the discs.
Attach the lid with a pusher (match arrow on the lid on the dot on the bowl, ) and rotate in a clockwise direction (). The lid lug must be located fully in the slot in the bowl handle.
Insert the mains plug.
Set the rotary switch to the desired setting.
Fill with contents that are to be sliced or shredded.
When adding contents that are to be sliced or shredded, apply only light pressure to the pusher. Remove the pusher and add ingredients through the feed tube.

Warning!
Empty the bowl before it becomes so full that the cutting or grating contents reach the carrier disc.
After using the appliance

Set the rotary switch to 0/off.
Remove mains plug.
Rotate the lid in an anti-clockwise direction and remove.
Remove a tool:
Take the tool holder together with the universal blade, whisking disc, or kneading hook out of the bowl. Remove the tools from the tool holder.
Take out the cutting discs by the plastic stud in the center. Take the tool holder out of the bowl.
Rotate bowl anti-clockwise and remove.
Clean all parts, see “Cleaning and servicing”.

Blender
Blade inserts with blender/cutting blade for mixing liquid or semi-solid food, for cutting/ chopping raw fruit and vegetables, for pureeing food.
Risk of injury from sharp blades / rotating drive!
Never place fingers in the attached blender! Do not remove/attach the blender until the drive is at a standstill. Do not touch the blades of the blade insert with bare hands. Clean them with a brush.
Risk of scalding!
If processing hot liquids, steam escapes through the funnel in the lid. Add a max. 0,4 liters of hot or frothing liquid.
Warning!
The blender may be damaged. Do not process deep-frozen ingredients (except ice cubes). Do not operate the blender when empty.
Fig. D

Place seal on the blade insert. Ensure that the seal is positioned correctly.

Important information
If the seal is damaged or not correctly positioned, liquid may run out.

Insert blade insert with blender/cutting blade into the blender jug and lock anti-clockwise ().
Turn blender jug over (blade insert face down).
Attach the blender jug (match the arrow on the jug to the dot on the appliance ) and rotate as far as possible in a clockwise direction ().
Add ingredients.
Maximum capacity, liquid = 1.0 liters
(frothing or hot liquids max. 0.4 liters).
Optimal processing capacity—solids = 80 g.
Attach lid and press firmly. Hold lid while working.
Insert the mains plug.
Set the rotary switch to the desired setting.
To add more ingredients, set the rotary switch to 0/off .
Remove the lid and add ingredients
Or
remove the funnel and gradually add solid ingredients through the refill opening
Or
pour liquid ingredients through the funnel.

After using the appliance

Set the rotary switch to 0/off.
Remove mains plug.
Rotate the blender in an anti-clockwise direction and remove.
Remove lid.
Loosen blade insert clockwise () and remove from the blender jug.
Clean all parts, see “Cleaning and servicing”.

Universal cutter
Use (depending on model):
— With the blade insert with blender/cutting blade for cutting and chopping meat, hard cheese, onions, herbs, garlic, fruit, and vegetables.
— With the blade insert with grinding blade for grinding and cutting fairly small quantities of spices (e.g. pepper, cumin, juniper, cinnamon, dried anise, saffron), grain (e.g. wheat, millet, linseeds), coffee, and sugar.
Risk of injury from sharp blades / rotating drive!
Do not remove/attach the universal cutter until the drive has stopped.
Do not touch the blades of the blade insert with bare hands. Clean them with a brush.
Fig. F shows guide values for the maximum quantities and processing times when working with the universal cutter.
Fig. E

Put down the universal cutter jug with the opening face up.
Add food, which is to be cut, to the jug. Note MAX mark on the jug!
Place seal on the blade insert. Ensure that the seal is positioned correctly.

Important information
If the seal is damaged or not correctly positioned, liquid may run out.

Insert blade insert (/ ) into the universal cutter jug and lock anti-clockwise ().
Turn universal cutter over (blade insert face down).
Attach the universal cutter (arrow on the jug on dot on the appliance ) and rotate all the way clockwise ().
Insert the mains plug.
Set the rotary switch to the desired setting.

Note: The longer the appliance remains switched on, the finer the ingredients are cut. Recommendations on using the accessories can be found in the section “Recipes/ Ingredients/Processing”.
After using the appliance

Set the rotary switch to 0/off.
Remove mains plug.
Rotate the universal cutter anti-clockwise and remove.
Turn universal cutter over (blade insert face up).
Loosen blade insert clockwise (e)) and remove from the universal cutter jug.
Empty jug.
Clean all parts, see “Cleaning and servicing”.

Cleaning and servicing

The appliance requires no maintenance. Thorough cleaning protects the appliance from damage and keeps it functional. An overview of cleaning the individual parts can be found in Fig. G.
Risk of electric shock
Never immerse the base unit in water or  place it under running water.
Warning!
Surfaces may be damaged. Do not use  abrasive cleaning agents.
Note: If processing e.g. carrots and red  cabbage, the plastic parts will become  discolored by a red film which can be  removed with a few drops of cooking oil.
Cleaning the base unit

Remove mains plug.
Wipe the base unit with a damp cloth. If  required, use a little detergent.
Then dry the base unit.

Cleaning the bowl and accessories
Risk of injury from sharp blades!
Do not touch blades of the universal blade with bare hands. When not in use, always store the universal blade in the blade guard. Clean them with a brush. Do not grip the sharp blades or edges of the cutting discs. Grip the discs by the plastic part in the center only!
All parts are dishwasher-proof. Do not wedge plastic parts in the dishwasher as they could warp.
Cleaning the blender / universal cutter
Risk of injury from sharp blades!
Do not touch the blades of the blade insert with bare hands. Clean them with a brush.
The blender jug (without blade insert), lid, and funnel are dishwasher-proof.
Do not clean the blade insert in the dishwasher, but under running water (do not soak in water). Remove seal for cleaning.

Troubleshooting

Risk of injury!
Before rectifying a fault, pull out the mains plug.
Fault:
The appliance does not start or the appliance switches off during operation.
Possible cause:
The bowl or lid or the accessory has not been attached correctly or has become detached.
Remedial action:

Set the rotary switch to 0/off.
Correctly attach bowl/lid or accessory and screw on all the way.
Switch the appliance on again. Important information If the fault cannot be eliminated, please contact customer service (see customer service addresses at the end of this booklet).

Storage

Fig. al The tools can be stored in the bowl to save space.

Disposal

Dispose of packaging in an environmentally-friendly manner. This – appliance is labeled in accordance with European Directive 2012/19/EU concerning used electrical and electronic appliances (waste electrical and electronic equipment — WEEE). The guideline determines the framework for the return and recycling of used appliances as applicable throughout the EU. Please ask your specialist retailer about current disposal facilities.

Guarantee

The guarantee conditions for this appliance are as defined by our representative in the country in which it is sold. Details regarding these conditions can be obtained from the dealer from whom the appliance was purchased. The bill of sale or receipt must be produced when making any claim under the terms of this guarantee.
Changes reserved.

Tool	Speed	Time	Recipes / ingredients / Processing
Or	low	approx. 1-2 min	Yeast dough -Max. 500 g flour -25 g yeast or 1 packet of dried yeast – 220 ml milk (room temperature) -1 egg -1 pinch of salt – 80 g sugar -60 g butter Grated rind of half a lemon ■ Add all ingredients (except the milk) to the bowl. ■ Set rotary switch to a low speed for 10 seconds. ■ Add milk and stir at low speed for about 11/2 minutes. Ingredients should be at the same temperature. When the dough has a smooth appearance, place in a warm location.
	M		Onions, garlic – from 1 onion, quartered, up to 300 g – from 1 clove of garlic up to 300 g ■ Process until it has been chopped to the required size.
	high		Hard cheese (e.g. parmesan) – 10 g to 200 g ■ Cut the cheese into cubes. ■ Process until it has been chopped to the required size.
	high		Chocolate 50 g to 200 g I; Cut or break the chocolate into pieces. ■ Process until it has been chopped to the required size.
	high		Parsley – 10 to 50g ■ Process until it has been chopped to the required size.
	high		Meat, liver (for mince, steak tartare, etc.) – 50 g to 500 g ■ Remove bones, gristle, and sinews. Dice the meat. Making sausage meat, stuffing, and paté: ■ Put the meat (beef, pork, veal, poultry, or even fish, etc.) together with other ingredients and spices into the bowl and mix into a dough.
	high	approx. 1.5-2 min	Strawberry sorbet I- 250 g frozen strawberries I- 100 g icing sugar – 180 ml cream ■ Put all ingredients in the bowl. Switch on immediately, otherwise, the mixture will go lumpy. Mix until a creamy sorbet form.
	low		Beaten egg white – 2 to 6 egg whites ■ Beat at a low speed.

Tool	Speed	Time	Recipes / Ingredients / Processing
	high		Whipped cream — 200 g to 400 g ■ Whisk at high speed.
	low/ high		Mayonnaise — 1 egg — 1 tsp. mustard — 150-200 ml oil — 1 tbs. lemon juice or vinegar — 1 pinch of salt — 1 pinch of sugar Ingredients should be at the same temperature. ■ Mix all ingredients (except oil) for several seconds at setting 1. ■ Switch appliance to setting 2, slowly pour oil through the feed tube, and mix until the mixture emulsifies. Eat the mayonnaise immediately, do not store it.
	high/M		Nuts, almonds — 50 g to 200 g ■ Remove shells completely, otherwise, the blender blade will be blunted. ■ Process until it has been chopped to the required size.
	high/M		Pur6eing fruit or vegetables — Apple sauce, spinach, carrot, and tomato purée; raw or cooked ■ Put ingredients and spices into the blender and purée.
	high		Chocolate-milk — 80 g-100 g cooled chocolate — approx. 400 ml hot milk ■ Chop up the chocolate in the blender, add the hot milk and mix briefly.
	M		Honey and hazelnut spread — 15 g hazelnuts — 110 g blossom honey (room temperature) ■ Put the nuts in the universal cutter jug and cut with the blender/ cutting blade for 20 seconds on setting M. ■ Remove the universal cutter jug, turn it over and take out the blade insert. ■ Add the honey. Close the universal cutter jug again with the blade and put it on the base unit. ■ Wait until all the honey has run down over the blade. Then mix everything for 5 seconds on setting M.
	Fig. F shows guide values for the maximum quantities and processing times when working with the universal cutter jug and the blade inserts.

BSH Home Appliances Pty. Ltd.
Gate 1, 1555 Centre Road
Clayton, Victoria 3168
Tel.: 1300 369 744*
Fax: 1300 306 818
mail to:
www.bosch-home.com.au
*Mo-Fr: 24 hours
BSH Home Appliances Ltd.
Grand Union House
Old Wolverton Road
Wolverton
Milton Keynes MK12 5PT
To arrange an engineer visit, to order
spare parts and accessories or for
product advice please visit
www.bosch-home.co.uk
or call Tel.: 0344 892 8979*
*Calls are charged at the basic rate, please check with your telephone service provider for exact charges
BSH Home Appliances Ltd.
Unit F 2, 4 Orbit Drive
Mairangi Bay
Auckland 0632
Tel.: 0800 245 700*
Fax: 0800 256 535
mail to:
www.bosch-home.co.NZ
* Mo-Fr: 8.30am to 4.00pm
(exclude public holidays)
BSH Household Appliances
Mfg. Pvt. Ltd. Arena House, Main Bldg,2nd Floor,
Plot No. 103, Road No. 12,
MIDC, Andheri East
Mumbai 400 093
Toll-Free 1800 266 1880*
www.bosch-home.com/in
* Mo-Sa: 8.00am to 8.00pm
(exclude public holidays)

Download

Bosch MCM3501M MultiTalent 3 Food Processor Instruction Manual

Was this manual helpful?