Canon imageCLASS LBP236dw Wireless Mobile Ready Laser Printer User Guide

image CLASS
LBP237dw, LBP236dw
Setup Guide

  • After you finish reading this guide, store it in a safe place for future reference.
  • The information in this guide is subject to change without notice.

1. Important Safety Instructions
Be sure to read these instructions before using the machine.

2. Setup Guide (this document)

3. User’s Guide / FAQ

https://oip.manual.canon/

Unless otherwise stated, illustrations used in this document are for the LBP237dw.

Checking the Items Included

Removing the Packing Material

  1. Install the machine in the location where it will be used.
  2. Remove all packing material.
    Remove all of the tape.
    Do not remove the sticker that covers the USB port until you actually use the USB port.

Loading Paper

Installing the Optional Part

If you are not using optional part, proceed to step 5

Before Installing the Optional Part
When installing the optional part after the machine has been installed, perform the following before starting work:

  1. Shut down the machine and your computer.
  2. Unplug the machine from the mains power outlet.
  3. Disconnect all cords and cables from the machine.

Cassette feeding module

  1. Install the cassette feeding module in the location where it will be used.

Connecting the Power Cord

Specifying the Basic Settings

When you turn on the machine for the first time, the Setup Guide starts up on the operation panel. Perform the initial machine setup by following the on-screen instructions.
Depending on your model, the items available for selection and the procedure for making choices may differ from those shown in this document. Proceed as directed in the screens shown.

Specifying the Security Settings

Specify the basic security settings to prevent unauthorized access to the machine.

  1. To use the Remote UI, select <Yes>.
    • To continue without using the Remote UI, select <No> and proceed to step 8 .
    •  When <A Remote UI Access PIN must be configured…> appears, proceed to step 5.
  2. To use System Manager mode, select <Yes>.
    • Set the System Manager ID and PIN so that you can configure the settings for extended functions and the management of access privileges, etc.
    • To continue without using System Manager mode, select <No> and proceed to step 5.
  3. Set the System Manager ID.
    Enter any number and then select <Apply>.
  4. Set the System Manager PIN.
    • Enter any number and then select <Apply>.
    • Re-enter the same PIN on the next screen as confirmation and select <Apply>.
  5. To use General User mode, select <Yes>.
    • Set the PIN to be used by general users to access the Remote UI.
    • To continue without using General User mode, select <No> and proceed to step 8.
  6. Set the Remote UI Access PIN.
    • Enter any number and then select <Apply>.
    • Re-enter the same PIN on the next screen as confirmation and select <Apply>.

Specifying the Network Settings

Specify the settings for connecting the machine to a network. Before proceeding, check that the computer and router are correctly connected to the network.

Wireless LAN

  1. Check the router’s “SSID” and “Network key.”
  2. To configure the settings, select <Yes> on the operation panel.
  3. Check the message and select <OK>. Depending on your model, this screen may not appear. In this case, proceed to step 4.
  4. Select the network with a matching SSID.
  5. Enter the password (network key) and select <Apply>.
    • Depending on your model, a connection confirmation screen may appear. To connect, select <Yes>.

Wired LAN
Connect the router to the machine with a LAN cable and then select <No> in the screen for choosing how to connect to the network.

Setting Up the Toner Replenishment Service

Use this procedure to set up the toner replenishment service. To use this service, you must enter into an agreement beforehand.

  1. Check the message and select <Next>.
  2. Check the conditions of use, and then choose whether or not to use the service.
    • To use the service: <Accept>.
    • To not use the service or not enter into an agreement: Select <Do Not Accept> and proceed to step 10 .
  3. When <Connection was successful.> appears, select <OK>.

Ending the Setup Guide

Check the description in the Application Library and then select <End>.
* If your model does not support the Application Library function, this step does not appear.

Installing the Software/Drivers

Install the software and drivers from the CD/DVD-ROM included, or visit the URL below and download them from the Canon website for your country/region. https://global.canon/en/support/

 Example: LBP236dw download

CANON U.S.A., INC.
One Canon Park, Melville, NY 11747, U.S.A.
Call Center: 1-800-OK-CANON

CANON MEXICANA, S. DE R.L. DE C.V.
Boulevard Manuel Avila Camacho #138 Piso 17, Col. Lomas de Chapultepec Mexico City, Mexico 11000
Call Center: 01800-710-7168

CANON INC.
30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan

CANON MARKETING JAPAN INC.
16-6, Konan 2-chome, Minato-ku, Tokyo 108-8011, Japan

CANON EUROPA N.V.
Bovenkerkerweg 59, 1185 XB Amstelveen, The Netherlands

CANON SINGAPORE PTE LTD
1 Fusionopolis Place, #15-10, Galaxis, Singapore 138522

CANON AUSTRALIA PTY LTD
Building A, The Park Estate, 5 Talavera Road, Macquarie Park, NSW 2113, Australia

CANON GLOBAL WORLDWIDE SITES
https://global.canon/

FT6-2803 (000) XXXXXXXXXX Copyright CANON INC. 2021 PRINTED IN XXXXX Imprimé XXX XXXXX