Electrolux E7SI1-60WB Refine 700 Steam Iron Instructions

Electrolux E7SI1-60WB Refine 700 Steam Iron Instructions

Introduction

Thank you for choosing an Electrolux product. In order to ensure the best results, always use original Electrolux accessories and spare parts. They have been designed especially for your product. This product is designed with the environment in mind. All plastic parts are marked for recycling purposes.

It may be possible that your steam iron does not produce steam immediately after filling it with water. The reason for this is that air trapped in the inner system can delay this function a few seconds. Please be patient and try it again by pressing the steam on/off button. For your convenience the steam will be produced after you release the steam on/off button for a few seconds and it is not necessary to press the button all the time. Find out your rhythm for the best steaming result.

INSTRUCTION MANUAL

Graphics and drawings in this manual are solely for illustration purposes and are subject to variations from actual product.
Read all instructions carefully before using the appliance for the first time.
Keep this manual for future reference.

COMPONENTS

A. Hot soleplate indicator
B. Water spray nozzle
C. Light indicator for heat-up/cool-down
D. Headlight illuminating ironing area
E. Temperature selector
F. Water filling container
G. Steam jet button
H. Spray button
I. Steam on/off button
J. Power cord
K. Flush Clean button
L. Soft Water Activator, replaceable
M. Water tank with max level indicator
N. Cord wrap facility
O. RESILIUM anodized ski-sloped soleplate
P. Water fill & Water Softener System cover
Q. Iron heel
R. Steam button lock

SAFETY ADVICE

  • This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
  • Keep the appliance and its power cord out of reach of children. Children should be supervised to ensure that they do not play with the appliance.
  • Cleaning and user maintenance shall not be performed by children without supervision.
  •  The appliance can only be connected to a power supply which voltage and frequency comply with the specifications on the rating plate.
  • The iron is not to be used if it has been dropped, if there are visible signs of damage on the iron or its cord or if it is leaking.
  • The appliance must only be connected to an earthed socket.
  • If the appliance or the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similar qualified person, in order to avoid hazard.
  • The iron must be used and rested on a stable surface. When placing the iron on it’s stand, ensure that the surface on which the stand is placed is stable.
  • Never leave the appliance unattended while connected to the supply mains.
  • The appliance must be switched off and the main plug withdrawn each time after use, before cleaning and maintenance.
  • The plug must be removed from the socket outlet before the water reservoir is filled with water.
  • The main cable must not come into contact with any hot parts of the appliance.
  • Do not immerse the appliance in water or any other liquid.
  • Do not exceed the maximum filling volume as indicated on the appliances.
  • This appliance is intended for domestic use only. The manufacturer cannot accept any liability for possible damage caused by improper or incorrect use.
  • This appliance is suitable to operate on both 50 and 60Hz.
  • CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.

GETTING STARTED AND OPERATING INSTRUCTIONS

  1. Before first use. Remove all adhesive remains and gently rub with a dampened cloth. Rinse water tank to remove foreign particles. Position the steam iron horizontally on the ironing-board or on a heat resistant, secure surface at the same height as an ironing-board. Unwind and straighten the power cord.
  2. Fill the steam iron with water. Make sure, the plug is outside the power outlet. Raise the heel of the iron, open the filling aperture cover (P). Use the water filling container provided (F), pour water to maximum level (M). Close the cover (P). This product is appropriate for use with tap water. It is recommended to use Electrolux AquaSense filtered water resp. a mix of 50% distilled, 50% tap water if the tap water is particularly hard. Always refill the water tank to MAX level using cold water.
    Caution! Never operate the appliance without any water in the tank.
    This product is equipped with a detachable Soft Water Activator (L), We recommend to replace the Soft Water Activator every 3 months..
    Before starting ironing, please test your iron on an old towel to ensure that no residues inside the iron are transferred to your garments. If necessary, wipe the soleplate with a slightly damp cloth.
  3. Connect the steam iron to the mains supply. Select the ironing programme from the temperature selector (E) on the steam iron. The light indicator (C) on the iron will pulsate when preheating. When turned on for the first time, temporary vapours/odours may occur. The iron is equipped with an auto-steam function, which automatically adjusts the steam output to the selected ironing programme supporting best ironing results.
  4. As soon as the selected temperature has been reached, the lights indicator (C) is on permanently and the headlight (D) turns on. Now the iron is ready to be used.
  5. To activate the steam function, press and hold the steam on/off button (I). To stop the steam function, release the steam on/off button.
  6. To use the continuous steam function, slide the steam button lock (R). To stop the continuous steam function, slide the steam button lock.
  7. For extra steam, press the steam jet button for one second. Iron with extra steam: Press the steam buttons the same time for improved crease removal. When releasing the buttons, use up the steam before putting the iron back on its heel.
    Caution! Never release steam while the iron is standing on its heel.
    Dry ironing: When not pressing steam buttons, the iron will be in dry mode.
  8. Using the spray mist. Pre-damp fabrics by pressing the spray button several times to release a fine mist; ensure the tank is at least half full.
  9. Steam hanging items. The vertical steam function is ideal for curtains and suits. Hold the iron at a distance of 10-20 cm and press the steam jet button.
  10. The iron is equipped with 3-way auto-off function. If the iron is left unattended on soleplate or the side, it automatically turns off after 30 seconds. If left unattended on the heel it automatically turns off after 8 minutes. To turn it on again, move the iron. A short beep can be heard before the iron is switched off by itself. To reactivate the iron, move it shortly and it is back to working mode.
  11. To switch-off the steam iron, turn the temperature selector to position 0, a short beep can be heard and all lights will turn off. Disconnect the mains plug. Never pull the supply cord. Instead, grasp the plug and pull. Empty the water tank and let the iron cool completely before storage.
  12. Always store the iron on its heel with the cord twisted loosley around the cable wrap facility. To clean exterior surfaces, use damp soft cloth and wipe dry. Do not use any chemical solvents, as they may damage the surface.

    CLEANING (DO NOT USE ANY DETERGENT) 
  13. Flush Clean (K). Fill the tank with water to max level (M) and select “Linen” programme. When headlight flashes, unplug the iron. Hold the iron over a sink, press the Flush Clean button (K). Use a full tank of water. Release button to stop Flush Clean function. Repeat the procedure if necessary.

    NOTE: DO NOT USE ANY DESCALING FLUID, VINEGAR OR CITRUS ACID!
  14. Soft Water Activator (L) is recommended right after Flush Clean. Open water filling cover (P) and pull the Soft Water Activator (L) out for disposal. Replace with new Water Softener System Electrolux EDC03/900923064. Both Flush Clean & Water Softener System in combination ensure a clean, soft steam for best ironing results and longer lifetime of your steam iron.
  15. Cleaning the soleplate (N). To remove burnt residues, iron over a damp cloth while the iron is still hot.
    To keep the soleplate smooth, avoid contact with metal objects. Never use scouring pads or harsh cleaners as they may damage the surface.

    HOT SOLEPLATE INDICATOR (A)
  16. Your appliance is equipped with hot soleplate indicator ThermoSafe™ which detects when the soleplate is hot by changing its colour from black to red.

    Note! During heat-up time, the soleplate might be hot even though the sticker didn’t turn red. Once the temperature of the soleplate is < 40°C, the colour changes back to black showing the iron is ready to be stored away.

IRONING CHART

FABRIC TEMPERATURE SET- TING IRONING RECOMMENDATION
Acrylic Outdoor / Delicate Dry iron inside out.
Acetate Outdoor / Delicate Dry iron inside out while still damp or use spray to dampen.
Nylon & Polyester Outdoor / Delicate Iron inside out while still damp or use spray to dampen.
Rayon Outdoor / Delicate Iron inside out.
Viscose Outdoor / Delicate Iron inside out.
Silk Outdoor / Delicate Iron inside out. Use an ironing cloth to prevent shiny iron marks.
Cotton blends Outdoor / Delicate Check the label and follow the manufacturer’s instructions. Outdoor setting is recommended for this kind of fiber.
Water-repellent breathable fabrics (excluding PVC- coatings) Outdoor Gently wash and air-dry your outdoor garments according to their care label instructions. Carefully and slowly dry iron the outside to reach all parts of your garment in order to reactivate the DWR (Durable Water Repellency) treatment and restore the water repellency of your garment*. You can use this setting after washing and air-drying your outdoor garment or anytime you want to restore the water repellency of certain areas of your garment.

* Better than air drying only for water – repellent outdoor garments

Wool & Wool blends Wool Iron inside out or use ironing cloth.
Cotton Cotton Dry iron while still damp or use spray to dampen. Use maximum steam.
Corduroy Cotton Steam iron inside out or use ironing cloth.
Linen Cotton or  Linen Iron inside out or use ironing cloth to prevent shiny iron marks, especially with dark-colored fabrics.

Dry iron while still damp or use spray to dampen. Use maximum steam.

FABRIC TEMPERATURE SET- TING IRONING RECOMMENDATION
Denim Cotton or  Linen Use maximum steam. Apply maximum steam by pressing and holding the steam on/off button.
Please follow the instructions of your garment care label.

Varied ironing speed and fabric dampness might cause optimal setting to differ from the recommendations in the table!

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE SOLUTION
Soleplate is not heating even though iron is turned on. Connection problem Check main power supply cable, plug and outlet.
Temperature control is in “Outdoor” position. Select higher programme like “ Cotton”.
Iron does not produce steam. Not enough water in tank. Fill water tank (see “Getting started”, no 2).
Selected temperature is lower than that specified to use with steam. Increase temperature to at least “Cotton”.
Steam jet and vertical steam jet function does not work. Steam jet function was used very frequently within a short period. Put iron on horizontal position and wait before using steam jet function.
Iron is not hot enough. Adjust the proper temperature to steam ironing (up toCotton”). Put iron in vertical position and wait until temperature indicator light turns off.
Water leaks from the soleplate during ironing. The iron is not hot enough. Select the Cotton setting (“Cotton” to maximum) suitable for steam ironing. Put the iron on its heel and wait until the headlight is on before you start ironing.
Flakes and impurities come out of the soleplate during ironing. You have used hard water, which has caused scale flakes to develop in the water tank. Clean the iron according to Cleaning section. Press and hold the steam button for about one minute to get steam. Then hold one more minute in order to clean the steam generating system. Before starting ironing, please test your iron on an old towel to ensure that no residues inside the iron are transferred to your garments.
Water leaks from the soleplate while the iron is cooling down or after it has been stored. The iron has been put in horizontal position while there is still water in the water tank. Empty the water tank.
Brown streaks come out of the soleplate while ironing and stain the linen. You may have used chemical descaling agents different from the recommendation. To prevent this from happening, it is recommended to exchange the Soft Water Activator according to the indications.
Fabric fibers have accumulated in the holes of the soleplate and are burning. Clean the soleplate with a damp soft cloth.
Fabrics might not be properly rinsed or the garments are new and have not been washed before ironing. Please rinse the fabrics properly before ironing.

DISPOSAL

This symbol on the product indicates that this product contains a battery which shall not be disposed with normal household waste.

This symbol on the product or on its packaging indicates that the product may not be treated as household waste. To recycle your product, please take it to an official collection point or to an Electrolux service center that can remove and recycle the battery and electric parts in a safe and professional way. Follow your country’s rules for the separate collection of electrical products and rechargeable batteries.

Electrolux reserves the right to change products, information and specifications without notice.

CUSTOMER CARE AND SERVICE

When contacting Service, ensure that you have the following data available: Model, PNC, Serial Number. The information can be found on the rating plate.

Due to the Electrolux policy of continual product development; specifications, colours, and details of our products and those mentioned in this manual are subject to change without notice.