SEALEY SCR92 Mechanics Detailing Utility Seat Instruction Manual
Instruction Manual
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble-free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
SAFETY
- WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this seat.
- Locate a seat in a suitable working area.
- WARNING! Use a seat on the level and solid ground, preferably concrete.
- Keep the seat clean and tidy in accordance with good workshop practice.
- DO NOT use the seat for any purpose other than that for which it is designed.
- DO NOT stand on the seat.
- DO NOT use the seat outdoors.
- DO NOT get the seat wet or use in damp or wet locations or areas where there is condensation.
- DO NOT clean the seat with any solvents which may damage the paint surface or the protective coating on the padded seat base.
- DO NOT use if damaged.
INTRODUCTION
Extra thick cushioned padding for added comfort when seated. Suitable for use in Bodyshop and Detailing environments as well as general garage use. Easy-rolling Ø100mm rubber castors with ball-bearing swivel. Storage trays and sliding draw for tools and components.
SPECIFICATION
Model No | SCR92 |
Capacity | 150kg |
Overall Size (W x D x H) | 550 x 420 x 375mm |
CONTENTS
1 Cushion 2 Top Frame 3 Drawer Holder 4 Drawer 5 Front Frame 6 Rear Frame 7 Side Tray A |
8 Side Tray B 9 Steel Base 10 Casters (2 with Brake) Lock Nuts included 11 Bolt 12 Washer 13Lock Nut |
ASSEMBLY
- Mount the rear panel (6) to the steel base(9) with 2 bolts (11) washers (12) and lock nuts (13).
- Slide the drawer holder (3) into the rear panel (6) with seat holder (2) on the top, and lock the seat holder (2) with the rear panel (6) by 2 bolts (11).
- Clip the front panel (5) to the front with steel base (9), drawer holder (3), and seat holder (2) in place, and lock the bottom 2 holes with bolts, washers, and lock nuts (11,12,13). Lock top 2 holes with 2 bolts (11).
- Mount 4 wheels (10) to the steel base (9) by each corner, be reminded there are 2 wheels with locks. Fix the wheels in place with Lock Nut (8).
- Put the Foam cushion (1) on the top. Hang the trays (7) on both sides of the seat. Insert the drawer (4) into the drawer holder (3)
MAINTENANCE
- Before each use, inspect the overall condition of the unit for broken, cracked or bent parts that may affect the proper operation.
- Regularly check the tightness of all fixings before use.
- Smear the castor bearings with a thin film of silicone grease quarterly.
- Ensure the castor wheels are able to rotate and swivel freely. Replace if necessary.
- Clean the seat cushion, trays, and frames with a moist cloth and mild detergent. DO NOT use solvents to clean the unit.
Parts support is available for this product. Please email or telephone 01284 757500
ENVIRONMENT PROTECTION
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications, and component parts without prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
© Jack Sealey Limited
SCR92 Issue 1 19/04/22