Bosch ALB 18 LI Cordless Leaf Blower 18 Volt System Instructions
Original instructions
Safety Notes
Warning! Read all safety warnings and all instructions. Make yourself familiar with the controls and the proper use of the product. Please keep the instructions safe for later
use!
Explanation of symbols on the machine
Keep bystanders a safe distance away from the product.
Operation
- Never allow children or people unfamiliar with these instructions to use the product. Local regulations may restrict the age of the operator. When not in use store the
product out of reach of children. - This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the product.
- Never operate the product while people, especially children or pets, are nearby.
- The user is responsible for accidents or hazards occurring to other people or their property.
- Other persons and animals should remain at a distance of 3 meters or more when the product is being used. The operator is responsible for third persons in the working area.
- Use the product only in daylight or with good artificial light.
- Never operate the product when you are tired, ill, or under the influence of alcohol, drugs, or medicine.
- Avoid operating the product in bad weather conditions especially when there is a risk of lightning.
- Always wear substantial clothing on the upper body and limbs when operating this product.
- Do not wear open rubber shoes or sandals when using the product. Always wear sturdy shoes and long trousers. Do not use barefoot.
- Failure to keep loose clothing from being drawn into air intake could result in personal injury.
- Only operate the product with a mounted nozzle.
- Failure to keep long hair tied back and away from the air inlet could result in personal injury.
- Thoroughly inspect the area where the product is to be used and remove all wires and other foreign objects.
- Check cable for damage before starting work and replace if necessary. Keep the cable away from heat, oil, and sharp edges.
- Always direct the cable to the rear away from the product.
- Never operate the product with defective guards or shields, or without safety devices, for example, a collection bag in place.
- Always ensure all handles and guards supplied are fitted when using the product. Never attempt to use an incomplete product or one fitted with an unauthorized modified
tin. - While operating the product always be sure of a safe and secure operating position at all times.
- Always be aware of your surroundings and stay alert for possible hazards that you may not hear whilst operate the leaf blower.
- Do not overreach and keep your balance at all times.
- Always be sure of your footing on slopes.
- Walk, never run.
- Keep all cooling air inlets clear of debris.
- Never blow debris in the direction of bystanders.
- Do not carry the product by cable.
- The wearing of a face mask is recommended.
- Wear eye protection.
- Do not modify the product.
Unauthorized modifications may impair the safety of your product and may result in increased noise and vibration. - A worn fan or blower housing (chips, cracks, nicks) may cause an increased risk of injury from thrown foreign objects. If the fan or blower housing is damaged, consult the Bosch hotline.
Recommendations for Optimal
Handling of the Battery Pack
- Do not open the battery. There is a risk of short-circuiting.
- In case of damage and improper use of the battery pack, vapors may be emitted. Ventilate the area and seek medical help in case of complaints. The vapors can
irritate the respiratory system. - Only use the battery with products from the manufacturer.
This is the only way in which you can protect the battery against dangerous overload. - The battery can be damaged by pointed objects such as nails or screwdrivers or by force applied externally.
An internal short circuit may occur, causing the battery to burn, smoke, explode or overheat. - Do not short-circuit the battery. There is a risk of explosion.
- Occasionally clean the venting slots of the battery using a soft, clean, and dry brush.
- Charge the machine only with the supplied battery charger.
Safety Warnings for Battery Chargers
Save all safety warnings and instructions for future reference.
Use the battery charger only when you fully understand and can perform all functions without limitation, or have received appropriate instructions.
- Never allow children, persons with physical, sensory, or mental limitations or a lack of experience and/or knowledge, and/or people unfamiliar with these instructions to use the battery charger. Local regulations may restrict the age of the operator.
- Supervise children at all times.
This will ensure that children do not play with the battery charger. - Charge only Bosch lithium-ion batteries with a capacity above 1,5 Ah (5 battery cells or more).
The battery voltage must match the battery charging voltage of the charger.
Do not charge non-rechargeable batteries. Otherwise, there is a danger of fire and explosion.
- Keep the charger clean. Dirt poses a risk of electric shock.
- Always check the charger, cable, and plug before use.
Stop using the charger if you discover any damage. Do not open the charger yourself, and have it repaired only by a qualified specialist using only original replacement
parts.
Damaged chargers, cables and plugs increase the risk of electric shock. - Do not operate the charger on an easily ignited surface (e.g. paper, textiles, etc.) or in a flammable environment. There is a risk of fire due to the charger heating up during
operation. - Do not cover the ventilation slots of the battery charger. Otherwise, the battery charger can overheat and no longer operate properly.
- For increased electrical safety, we recommend using a residual current device with a max. tripping current of 30 mA. Before using, always check your residual current device.
Symbols
The following symbols are important for reading and understanding the original instructions. Please take note of the symbols and their meaning. The correct interpretation of
the symbols will help you to use the product in a better and safer manner.
| Symbol | Meaning |
| Movement direction | |
| Reaction direction | |
| Switching On | |
| Switching Off | |
| Permitted action | |
| Prohibited action | |
CLICK! |
Audible noise |
| Weight |
Intended Use
The product is intended for blowing leaves, and garden waste such as grass, twigs, and pine needles.
Product Features (see figure A)
The numbering of the product features refers to the illustration of the product on the graphics pages.
- On/Off switch
- Motor unit
- Button for unlocking nozzle
- Nozzle
- Battery A)
- Charger A)
A) Accessories shown or described are not included with the product as standard. You can find the complete selection of accessories in our accessories range.
Technical Data
| Cordless leaf blower | ALB 18 L1 | |
| Article number | 3 600 HAO 3.. | |
| Rated voltage | V | 18 |
| Airflow speed”‘ | km/h | 210 |
| Weight according to EPTA-Procedure 01:2014A) | kg | 1.8 |
| Serial number | see type plate on garden tool | |
| Recommended ambient temperature during charging | °C | 0 … +35 |
| Permitted ambient temperature during operation B) and storage | °C | -20 … +50 |
| Battery type | PBA 18V…W-. 1.5 Ah, 2.0 Ah, 2.5 Ah, 3.0 Ah | |
| A) Depends on battery in use B) Limited performance at temperatures <0 °C | ||
| Charger | AL 1810 CV | AL 1815 CV | AL 1830 CV | AL 1880 CV | |
| Charging current | A | 1.0 | 1.5 | 3.0 | 8.0 |
| Charging period (battery discharged) | |||||
| – Battery with 1.5 Ah | min | 94 | 63 | 33 | 27 |
| – Battery with 2.0 Ah | min | 124 | 84 | 45 | 30 |
| – Battery with 2.5 Ah | min | 154 | 105 | 60 | 36 |
| – Battery with 3.0 Ah | min | 185 | 130 | 72 | 46 |
| – Battery with 4.0 Ah | min | 244 | 168 | 95 | 35 |
| – Battery with 6.0 Ah | min | 364 | 260 | 130 | 62 |
| Weight according to EPTA‑Procedure 01:2014 | kg | 0.17 | 0.38 | 0.40 | 0.60 |
| Protection class | |||||
Noise/Vibration Information
| 3 600 HA0 3.. | ||
| Noise emission values determined according to EN 50636-2-100. Typically the A-weighted noise levels of the product are: | ||
| – Sound pressure level | 60 | |
| – Sound power level | 80 | |
| – Uncertainty K | = 3.0 | |
| Vibration total values ah (triax vector sum) and uncertainty K determined according to EN 50636-2-100 | ||
| – Vibration emission value ah | m/s2 | < 2.5 |
| – Uncertainty K | m/s2 | = 1.5 |
Assembly
- Caution: Switch the garden tool off and remove the battery from the machine before adjusting or cleaning.
Mounting the nozzle (see figure B)
Slide the nozzle (4) onto the motor unit. Take care not to pinch your fingers during assembly.
Inserting/Removing the Battery (see figure C)
Note: Using unsuitable batteries can lead to malfunctions or damage to the machine.
Insert the charged battery (5). Ensure the battery is inserted correctly.
To remove the battery (5) from the machine, press the battery unlocking button and pull the battery out.
Switching on
- Before any work on the garden product itself (e. g. maintenance, tool change, etc.) as well as during transport and storage, remove the battery from the garden product. There is a danger of injury when unintentionally actuating the On/Off switch.
- The machine continues to blow for a few seconds after being switched off. Allow the motor to stop rotating before switching “on” again. Do not rapidly switch off and on.
Charging the Battery
- Observe the correct mains voltage! The voltage of the power supply must correspond with the data given on the nameplate of the battery charger. Battery chargers marked with 230 V can also be operated with 220 V.
The battery is equipped with temperature monitoring that allows charging only in the temperature range between 0°C and 35 °C. In this manner, a high battery service life is achieved.
Note: The battery is supplied partially charged. To ensure full battery capacity, completely charge the battery in the battery charger before using for the first time.
The lithium-ion battery can be charged at any time without reducing its service life. Interrupting the charging procedure does not cause damage to the battery.
The “Electronic Cell Protection (ECP)” protects the lithium-ion battery against deep discharging. When the battery is empty, the product is switched off by means of a protective circuit: The product no longer operates.
Do not continue to press the On/Off switch after an auto
matic shut-off of the product. The battery could become damaged.
Charging Procedure
The charging procedure starts as soon as the mains plug of the charger is plugged into a socket outlet and the battery (5) is inserted onto the charger (6).
Due to the intelligent charging method, the charging condition of the battery is automatically detected and the battery is charged with the optimum charging current, depending on battery temperature and voltage.
This gives longer life to the battery and always leaves it fully charged when kept in the charger for storage.
Meaning of the Indication Elements
(AL 1810 CV)
The charging process is indicated by the flashing of the battery charge indicator.
Solid light on the battery charge indicator
Understanding the Indicators (AL 1815 CV)
Flashing battery charge indicator
Continuous lighting of the battery charge indicator
When the battery is not inserted, continuous lighting of The battery charge indicator indicates that the mains plug is inserted in the socket outlet and that the battery charger is ready for operation.
Meaning of the Indication Elements (AL 1830 CV)
(Fast) Flashing of the Green Battery Charge Indicator
Note: The rapid-charging procedure is only possible when the battery temperature is within the allowable charging temperature range, see section “Technical Data”.
(Slow) Flashing of the Green Battery Charge Indicator
The battery can be removed for immediate use.
Continuous Lighting of the Green Battery Charge Indicator
When the battery is not inserted, continuous lighting of the battery charge indicator indicates that the main plug is inserted in the socket outlet and that the battery charger
is ready for operation.
Continuous Lighting of the Red Battery Charge Indicator
Flashing Red Battery Charge Indicator
Charging Advice
With continuous or several repetitive charging cycles without interruption, the charger can warm up. This is not meaningful and does not indicate a technical defect of the
battery charger.
A significantly reduced working period after charging indicates that the battery is used and must be replaced.
Observe the notes for disposal.
Operation
- Caution: Switch the garden tool off and remove battery from the machine before adjusting or cleaning.
Switching On and Off (see figure D)
To switch on, push the On/Off switch (1).
To switch off, release the On/Off switch (1).
Disassembling (see figure B)
Press button (3) in and remove the nozzle (4).
Working instruction (see figure E)
When operating, always hold the machine approximately 3 cm above the ground.
Do not blow hot, flammable or explosive material.
Troubleshooting
Cordless leaf blower
| Problem | Possible Cause | Corrective Action |
| The machine fails to operate | Battery discharged | Recharge battery |
| Battery too hot/cold | Allow cooling/warm | |
| Machine defective | Contact Service Agent | |
| Internal wiring of garden tool defective | Contact Service Agent | |
| Garden tool function intermittently | On/Off switch defective | Contact Service Agent |
| Excessive vibrations/ noise | Machine defective | Contact Service Agent |
| Run time per battery charge too low | The battery has not been used for a long period or only for short terms | Fully charge the battery; also see “battery charging” |
| Battery dead or defective | Replace the battery | |
| Air inlet/outlet blocked | Clear the air inlet/outlet | |
| Machine blow | Tube obstructed | Clear tube |
| The tube cannot be mounted on the machine | Incorrect assembly | see “assembly” |
Battery and charger
| Problem | Possible Cause | Corrective Action |
| Flashing red battery charge indicator No charging procedure possible | Battery not (properly) inserted | Properly insert the battery into charger |
| Battery contacts contaminated | Clean the battery contacts (e. g. by inserting and removing the battery several times) or replace the battery | |
| Battery defective | Replace the battery | |
| Battery charge indicators do not light up | The mains plug of the battery charger is not plugged in (properly) | Insert the mains plug (fully) into the socket-outlet |
| Socket outlet, mains cable, or battery charger defective | Check the mains voltage; have the battery charger checked by an authorized after-sales service agent for Bosch power tools |
Maintenance and Service
Maintenance, Cleaning, and Storage
- Before any work on the garden product itself (e. g.
maintenance, tool change, etc.) as well as during
transport and storage, remove the battery from the
garden product. There is a danger of injury when unintentionally actuating the On/Off switch. - For safe and proper working, always keep the product clean.
Do not place other objects on the garden product.
To ensure safe and efficient operation, always keep the product and the ventilation slots clean. Never spray the product with water.
Never immerse the product in water.
Store the product in a secure, dry place, out of the reach of children.
Do not place other objects on the product.
Keep all nuts, bolts, and screws tight to ensure safe working with the product.
Inspect the product and replace worn or damaged parts for safety.
Ensure replacement parts fitted are Bosch-approved.
Battery Maintenance
Use the following procedures to enable optimum usage of the battery:
– Protect the battery against moisture and water.
– Store the machine and battery only within a temperature range between –20 °C and 50 °C. As an example, do not leave the battery in the car in summer.
– It is recommended that the battery is not stored within the product but stored separately.
– Do not leave the battery in the product in direct sunlight.
– The ideal storage condition for the battery is 5 °C.
– Occasionally clean the venting slots of the battery using a soft, clean, and dry brush.
A significantly reduced working period after charging indicates that the battery is used and must be replaced.
After-Sales Service and Application Service
Our after-sales service responds to your questions concerning maintenance and repair of your product as well as spare parts. You can find explosion drawings and information on spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you with any questions about our products and their accessories.
In all correspondence and spare parts orders, please always include the 10-digit article number given on the nameplate of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
You can find further service addresses at:
www.bosch-pt.com/serviceaddresses
Transport
The contained lithium-ion batteries are subject to the Dangerous Goods Legislation requirements. The batteries are suitable for road transport by the user without further restrictions.
When shipping by third parties (e.g.: by air transport or forwarding agency), special requirements on packaging and labeling must be observed. For the preparation of the item being shipped, consulting an expert for hazardous material is required.
Dispatch battery packs only when the housing is undamaged. Tape or mask off open contacts and pack up the battery in such a manner that it cannot move around in the packaging. Please also observe the possibility of more detailed national regulations.
Disposal
The product, batteries, accessories, and packaging should be sorted for environmental-friendly recycling.
Only for EU countries:
According to the European Guideline 2012/19/EU, products that are no longer usable, and according to the European Guideline 2006/66/EC, defective or used battery packs/ batteries, must be collected separately and disposed of in an environmentally correct manner.
Battery packs/batteries:
Li-ion:
Please observe the notes in the section on transport (see “Transport”, page 18).
| EU Declaration of Conformity | We declare under our sole responsibility that the stated products comply with all applicable provisions of the directives and regulations listed below and are in conformity with the following standards. |
| Cordless leaf blower
Article number |
| ALB 18 LI | 3 600 HA0 3.. | 2006/42/EC 2014/30/EU 2011/65/EU 2000/14/EC EN 60335-1:2012+A11:2014+A13:2017 +A1:2019+A2:2019+A14:2019 EN 50636-2-100: 2014 EN 55014-1:2017+A11:2020 EN 55014-2:2015 EN IEC 63000:2018 |
2000/14/EC: Measured sound power level 80 dB(A), uncertainty K = 3,0 dB, guaranteed sound power level 83 dB(A) Conformity assessment procedure in accordance with annex V. Product category: 34 Technical file at: *
* Robert Bosch Power Tools GmbH,
PT/ECS, 70538 Stuttgart, GERMANY
Henk Becker
Chairman of ExecutiveManagement
Helmut Heinzelmann
Head of Product Certification
Robert Bosch Power Tools GmbH, 70538 Stuttgart, GERMANY
Stuttgart, Robert Bosch Power Tools GmbH, 70538 Stuttgart, GERMANY
Stuttgart, 03.11.2020
Robert Bosch Power Tools GmbH
70538 Stuttgart GERMANY
www.bosch-pt.com
ALB 18 LI