Philips ADD4947 Dispenser User Manual

PHILIPS ADD4947 Dispenser User Manual

Main technical specification

Model ADD4947
Rated voltage 220V-240V-
Rated frequency 5OHz
Heating power Low power 170W / High power 35OW
Cooling power  

65W

Hot water 906, 3.8L/h with high power, 1.5L/h with low power
Cold water a15°C, 0.6L/h
Environmental temp. ST
Relative humidity ≤90
Protection of anti-electric shock I

Product overview

  1. Indicator
  2. Cold water fauce
  3. Coldwater press paddle
  4. Drip tray
  5. Lower cabinet door
  6. Safety lock button
  7. Hot water button
  8. Hot water faucet
  9. Water bottle cap with hose
  10. Power switch
  11. Cooling fan
  12. Cold water flushing drain
  13. Hot water flushing drain
  14. Power cord

Indicator panel and switch

 

Power on indicator
When the dispenser is connected with power and the power button switches on, the indicator will light up.

Heating indicator
When the dispenser is heating up the water in the hot water tank, the light will go on.

Cooling indicator
When the dispenser is cooling the water in the cold water tank, the light will be on.

Water shortage indicator
When there is no water in the bottle, the water shortage indicator will be on. Please replace with a new bottle.

At the back of the dispenser there isa black switch which controls the heating power. You may press it to switch between high power, low power and OFF.

Every time when you plug in the water dispenser again, it will need some time for getting hot and cold water.

Turn the red heating switch to ‘I’, please wait for around 30 minutes for hot water;
Turn the red heating switch to ‘II’, please wait for around 15 minutes for hot water;
Turn the green cooling switch to ‘I’, please wait for around an hour for cold water.

Instruction

Unpacking the water dispenser

Cut and remove the straps from the box. DO NOT turn the box upside down, or lay it on
its side. Remove the plastic bag. Lift the water dispenser form the bottom of the carton box.

Wipe it clean if necessary.
Place the machine on a hard, flat surface. Make certain the the appliance is leveled. The appliance should not be placed near direct sunlight or other source of heat.

It is best to place the water dispenser in an area with good air circulation. Make sure there is at least 4 inches (1Ocm) of space between the back of your water dispenser and the wall.

Keep a minimum distance of 2 inches (Scm) on each side of your water dispenser.

Warning: the drain plug on the back of the unit may become loose during shipping. Fasten  the drain plug tightly before you start to operate the unit. If the drain plug is loose, the unit may leak and cause floor damage.

Settling water bottle

Make sure the water dispenser is not plugged into an electrical outlet.
Open the door of the lower cabinet.
Place full water bottle on floor. Remove the plastic cover over the mouth of the water bottle.
Place the stainless tube inside the bottle and place the water bottle cap firmly over the mouth of the water bottle.
Attach the hose to the top of the cap using the quick connect system shown below”.
Slide the bottle inside the cabinet and close the lower cabinet door.

Your new water dispenser features an adjustable quick connect system. For proper operation, make sure the connector is sealed tight (Fig. 1);
The connector can be removed easily for cleaning with warm soapy water (Fig. 2);
The stainless steel tube can be adjusted up and down to accommodate both 3 gallon and 5 gallon water bottle (Fig. 3).

Note: If there is nota secure connection between the hose cap and the connector on the water dispenser, the water pump will operate but the water dispenser will not dispense water. Make sure the hose is connected to the water dispenser correctly.

Dispense water

  • Plug the water dispenser into a grounded power outlet.
  • The unit will pump the water from the water bottle into the cooling and heating tanks.
  • Press the child safety lock button first, then press the hot water button until water flows out.
  • Press the cold water panel until water flows out also.
  • Turn on the power switch on the back of the unit.
  • The cooling or heating feature will start running. The indicator light will be on when heating or cooling function is working.
  • Do not touch both switches during the time.
  • Enjoy the hot or cold water you need.
  • If you are not going to use hot water, turn the black heating switch to ‘O’; if you are not going to use cold water, turn the green cooling switch to “O” to conserve energy.

Note: please wait until the water pump stops running before using the the appliance.
If the water tank is not full, no water will dispense from the water faucet.

Precautions

Warning
When using electrical appliances, basic safety precautions should be followed to reduce the risk of fire, electric shock, and injury to persons or property. Read all instructions before using any appliance.

  • Do not let hot water touch bare skin. Keep combustible material such as furniture, bedding, pillows, clothes, and/or papers away from the back of the the appliance.
  • Do not operate this, or any other appliance with a damaged power cord. No other appliance should be plugged into the same outlet. Be sure that the plug is fully inserted into the outlet.
  • Do not run the power cord over carpeting or other heat insulators. Do not cover the cord. Keep cord away from high traffic areas, and do not submerge in water.
  • We do not recommend the use of extension cord as it may overheat and cause a risk of fire.
  • Exercise caution and use reasonable supervision when the appliance is used by or near children.
  • Do not use your water dispenser outdoors. Place the water dispenser away from direct sunlight and make sure that there is at least 6 inches (15cm) of space between the back of your The appliance and wall. Keep a minimum of 2 inches (Scm) on each side of your The appliance free.
  • Do not use this product to dispense anything other than water.
  • To avoid a hazard due to instability of the appliance, it must be placed on even and flat surface.
  • If the supply cord is damaged, please contact aftersales personnel to replace it in order to avoid a hazard.
  • This water dispenser must be positioned so that the plug is accessible.
  • Disconnect the plug from the outlet when not in use.
  • Remove power plug or disconnect from the main power source before servicing the appliance.

Cleaning and maintenance

  • To avoid accidents, turn off and unplug the water dispenser from the outlet before cleaning.
  • A soft damp cloth may be used to clean the surface of the water dispenser. When necessary, a mild detergent may be used. DO NOT use corrosive chemical solvents to clean the
  • The appliance, as this may damage the surface of the water dispenser.
  • DO NOT pour water on the exterior of the The appliance to avoid getting the internal electrical system wet. DONOT immerse the The appliance in water when cleaning.
  • The water bottle cap, hose, and drip tray may be washed in a dishwasher (top rack only).
  • Keep the water dispenser 6 inches (15cm) away from the wall so it can work properly.
  • Make certain all ventilation openings are clear of obstruction.
  • Do not damage the heating or cooling system.
  • If you will not use the water dispenser foar long period of t1me, please unplug the power cord and drain the water dispenser. Drain the water from all faucets, then remove the drain cap on back and allow it to drain. Make certain the drain cap is fastened tightly when finished.

Trouble shooting

Trouble Possible causes Solutions
The appliance does not dispense hot and cold water.  
  1. The appliance is unplugged.
  2. Main power supply is off.
  3. Damaged water dispenser.
  4. The water bottle cap is not attached properly to the connector on the water dispenser.
  1. Plug the power cord into an socket.
  2. Reestablish main power supply.
  3. Replace the dispenser or send for service.
  4. Connect properly.
 

The appliance does not dispense cold water.
  1. Over consumption of cold water in a short time.
  2. System Malfunction
  3. The ventilation around the the appliance is insufficient.
  4. The temperature of water in the water bottle is too high. (When the bottle is exposed to direct sunlight for a long time.)
  1. Wait a moment for the water to cool.
  2. Contact aftersales personnel for support.
  3. Space the the appliance from the wall by more than 15 cm.
  4. Place the water bottle in a cool location out of direct sunlight.
 

The appliance does not dispense hot water.
  1. Over consumption of hot water in a short time.
  2. System Malfunctions.
  1. Wait a moment for the water to heat.
  2. Contact aftersales personnel for support.
Water leaks from the nozzle. The nozzle has been damaged. Contact aftersales personnel for support.
Water is dripping out of the water dispenser and  onto the floor.
  1. The hose connector is not connected properly or the inside hot or cold water tanks is leaking.
  2. The drain cap on the Dack is not fastened properly.
  
  1.  Make sure the hose connector is properly connected. Contact dealer if a water tank is leaking.
  2. Tighten the drain cap. If the sealing silicon material inside the drain cap is torn or damaged, then replace with a new one.

Guarantee and Service

If you need information or if you have any questions, please visit the Philips website at www.philips.com or contact the consumer care center in your country. If there is no consumer care center in your country, go to the local dealer.

Packing list

Water Dispenser 1x
User Manual 1x
Warranty Card 1x

Register your product and learn more in the website link below: www.philips.com/water

Specifications are subject to change without notice 2021 AquaShield All rights reserved. The Philips trademark and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. used under license.
This product has been manufactured by and is sold under the responsibility of Hong Kong AquaShield Health Technology Company Limited and Hong Kong AquaShield Health Technology Company Limited is the warrantor in relation to this product. Rev A MAY 21

Diimpor oleh:
PT Akari Indonesia J1. Raya Waru No. 1. Waru-Sidoarjo,INDONESIA Nomor Tanda Pendaftaran: IMKG.849.04.2021