Yamaha YDP-105 Digital Piano Owner’s Manual

YAMAHA YDP-105 Digital Piano Owner’s

FCC INFORMATION (U.S.A.)

IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the prod-act.

IMPORTANT: When connecting this product to accesso-rise and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this prod-uct in the USA.
NOTE: This product has been tested and found to com-ply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Com-pliancy with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:

• Relocate either this product or the device that is being affected by the interference.
• Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.
• In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to dis-tribute this type of product. If you cannot locate the appropriate retailer, please contact Yamaha Corporation of America, 6600 Orange Thorpe Ave., Buena Park, CA90620, USA.
The above statements apply ONLY to those products dis-tribute by Yamaha Corporation of America or its subsid-diaries.

COMPLIANCE INFORMATION STATEMENT

(Suppliers declaration of conformity procedure)
Responsible Party: Yamaha Corporation of America
Address: 6600 Orange Thorpe Ave. Buena Park, Calif. 90620
Telephone: 714-522-9011
Type of Equipment: Digital Piano
Model Name: YDP-105

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received including interference that may cause undesired operation

The model number, serial number, power requirements, etc., may be found on or near the name plate, which is at the bottom of the unit. You should note this serial number in the space provided below and retain this manual as a permanent record of your purchase to aid identification in the event theft.

For AC Adaptor
CAUTION: RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4.  Follow all instructions.
5.  Do not use this apparatus near water.
6. Clean only with dry cloth.
7.  Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions
8.  Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
    Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING
Especially in the case of children, a guardian should provide guidance on how to properly use and handle the product before actual use.
Please keep this manual in a safe and handy place for future reference.
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:

Power Supply

• Do not place the power cord near heat sources such as heaters or radiators. Also, do not excessively bend or otherwise damage the cord, or place heavy objects on
• Do not touch the product or the power plug during an electrical storm.
• Only use the correct voltage specified for the The required voltage is printed on the name plate of the product.
• Use the specified AC adaptor
• Check the power plug periodically and remove any dirt or dust which may have accumulated on it.
• Insert the power plug firmly all the way into the AC outlet. Using the product when it is not plugged in sufficiently can cause dust to accumulate on the plug, possibly resulting in fire or skin burns.
• When setting up the product, make sure that the AC outlet you are using is easily. If some trouble or malfunction occurs, immediately turn off the power switch and disconnect the plug from the outlet. Even when the power switch is turned off, as long as the power cord is not unplugged from the wall AC outlet, the product will not be disconnected from the power source.
• Do not connect the product to an electrical outlet using a multi-plug outlet Doing so can result in lower sound quality, or possibly cause overheating in the outlet.
• When disconnecting the power plug, always hold the plug itself and not the Pulling by the cord can damage it and cause electric shocks or a fire.
• If not using the product for long periods of time, be sure to pull the power plug from the AC

Do Not Disassemble

• This product contains no user-serviceable Do not attempt to disassemble the internal parts or modify them in any way.

Water Warning

• Do not expose the product to rain, use it near water or in damp or wet conditions, or place on it any containers (such as vases, bottles or glasses) containing liquids which might spill into any openings or places where water may A liquid such as water getting into the product may cause a fire, electric shocks, or malfunctions.
• Use the AC adaptor indoors Do not use in any wet environments.
• Never insert or remove a power plug with wet

Fire Warning

• Do not place any burning items or open flames near the product, since they may cause a fire.

Using the bench (if included)

• Do not place the bench in an unstable position where it might accidentally fall
• Do not play carelessly with or stand on the bench. Using it as a tool or stepladder or for any other purpose might result in accident or
• Only one person should sit on the bench at a time, in order to prevent the possibility of accident or
• If the bench screws become loose due to extensive long-term use, tighten them periodically using the specified tool in order to prevent the possibility of accident or injury.
• Keep special watch over any small children so that they don’t fall off the rear of the Since the bench does not have a backrest, unsupervised use may result in accident or injury.

DMI-10 1/2
If you notice any abnormality

• If any of the following problems occur, immediately turn off the power switch and disconnect the power plug from the Finally have the device inspected by Yamaha service personnel.
  • The power cord or plug becomes frayed or
  • Unusual smells or smoke are

• Some object, or water has been dropped into the product.
• There is a sudden loss of sound during use of the
• Cracks or other visible damage appear on the

CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the product or other property. These precautions include, but are not limited to, the following:

Assembly

• Assemble the product in the proper sequence by following the assembly instructions in this manual. Also, make sure to tighten the screws or bolts Failure to do so might result in damage to the product or even injury.

Location

• Do not place the product in an unstable position or a location with excessive vibration, where it might accidentally fall over and cause
• Do not go near the product during an earthquake. Strong shaking during an earthquake could cause the product to move or tip over, resulting in damage to the product or its parts, and possibly causing injury.
• When transporting or moving the product, always use two or more Attempting to lift the product by yourself may result in injuries, such as back injuries, or cause the product to be dropped and broken, which could lead to other injuries.
• Before moving the product, remove all connected cables, to prevent damage to the cables or injury to anyone who might trip over them.

Connections

• Before connecting the product to other electronic components, turn off the power for all Before turning the power on or off for all components, set all volume levels to minimum.
• Be sure to set the volumes of all components at their minimum levels and gradually raise the volume controls while playing the product to set the desired listening

Handling

• Do not insert your finger or hand in any gaps on the key cover or product. Also take care that the key cover does not pinch your finger.
• Do not insert foreign materials such as metal or paper into any openings or gaps of the product. Failure to observe this may cause a fire, electric shocks, or
• Do not rest your weight on, or place heavy objects on the product, and do not use excessive force on the buttons, switches or connectors.
• Keep small parts out of the reach of Your children may accidentally swallow them.
• Do not use the product or headphones for a long period of time at a high or uncomfortable volume level, since this can cause permanent hearing loss. If you experience any hearing loss or ringing in the ears, consult a physician.
• Remove the power plug from the AC outlet before cleaning the Failure to observe this may cause electric shocks.

Always turn the power off when the instrument is not in use.
Even when the (Standby/On) switch is in standby status (power lamp is off), electricity is still flowing to the instrument at the minimum level.
When you are not using the instrument for a long time, make sure you unplug the power cord from the wall AC outlet.

NOTICE
To avoid the possibility of malfunction/ damage to the product, damage to data, or damage to other property, follow the notices below.

• Handling
• Do not use the instrument in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Otherwise, the instrument, TV, or radio may generate
• When you use the instrument along with an app on your smart device, such as a smartphone or tablet, we recommend that you enable “Airplane Mode” on the device to avoid noise caused by communication.
• Do not expose the instrument to excessive dust or vibrations, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day) to prevent the possibility of disfiguration, damage to the internal components or unstable operation. (Verified operating temperature range: 5° – 40°C, or 41° – 104°F.)
• Do not place vinyl, plastic or rubber objects on the instrument, since this might discolor the
• Maintenance
• When cleaning the instrument, use a soft and dry/slightly damp cloth. Do not use paint thinners, solvents, alcohol, cleaning fluids, or chemical-impregnated wiping cloths.
• During extreme changes in temperature or humidity, condensation may occur and water may collect on the surface of the If water is left, the wooden parts may absorb the water and be damaged. Make sure to wipe any water off immediately with a soft cloth.

Information

• About copyrights
  The copyright of the “content”*1 installed in this product belongs to Yamaha Corporation or its copyright holder. Except as permitted by copyright laws and other relevant laws, such as copying for personal use, it is prohibited to “reproduce or divert”*2 without the permission of the copyright When using the content, consult with a copyright expert. If you create music or perform with the contents through the original use of the product, and then record and distribute them, the permission of Yamaha Corporation is not required regardless of whether the distribution method is paid or free of

1. The word “content” includes a computer program, audio data, Accompaniment Style data, MIDI data, waveform data, voice recording data, music score, and score data, etc.
2. The phrase “reproduce or divert” includes taking out the content itself in this product, or recording and distributing it without changes in a similar manner.

• About functions/data bundled with the instrument
  Some of the preset songs have been edited for length or arrangement, and may not be exactly the same as the
• About this manual
  The illustrations as shown in this manual are for instructional purposes only. “QR Code” is a registered trademark of DENSO WAVE The company names and product names in this manual are the trademarks or registered trademarks of their respective
• Tuning
  Unlike an acoustic piano, this instrument does not need to be tuned by an expert (although the pitch can be user- adjusted to match other instruments). This is because the pitch of digital instruments is always maintained
• About disposal
  When disposing of this product, please contact the appropriate local authorities.

When Moving/Installing the Instrument
When moving the instrument after assembly (page 16), be sure to keep the instrument horizontal and hold with two or more people. Do not subject the instrument to excessive vibration or shock. After re-installation, check the assembly checklist.
If you move to another location, you can transport the instrument along with other belongings. The unit can be transported either assembled or disassembled.
We recommend that you place the instrument away from the wall by about 5 cm to optimize and enhance the overall sound even further.

CAUTION
Always hold the bottom of the main unit. Moving the unit by holding any part other than the bottom may cause damage to the unit or personal injury.
NOTICE: Rotate the adjuster under the pedal until it no longer touches the floor surface before moving the instrument. The adjuster can damage the floor.

Thank you for choosing this Yamaha digital piano.
This instrument provides exceptionally high-quality sound and expressive control for your playing enjoyment.
In order to make the most of the performance potential and features of the instrument, please read the manuals thoroughly, and keep them in a handy place for later reference.

About the Manuals
This instrument has the following manuals.

Included Manuals
Owner’s Manual (this book) Explains how to use the instrument.

Online Manuals
Quick Operation Guide Shows in chart form the functions assigned to the keyboard for quick understanding. It also contains various lists, such as those of Voices, Songs, etc.

https://manual.yamaha.com/mi/kb-ekb/ydp-105/

• Smart Device Connection Manual Explains how to connect the instrument to a smartphone or tablet, etc.
• Computer-related Operations Includes instructions on connecting this instrument to a computer.
• MIDI Reference Contains the MIDI Data Format and MIDI Implementation chart, as well as descriptions on MIDI functions such as MIDI channel and Local Control settings.

To obtain these materials, access the Yamaha Downloads website, then enter the model name for searching the desired files. Yamaha Downloads https://download.yamaha.com/

Included Accessories

• Owner’s Manual
• Online Member Product Registration
• AC adaptor
• Bench

* May not be included depending on your particular area. Please check with your Yamaha dealer.

Smart device application – “Smart Pianist”
With the specially developed “Smart Pianist” app running on your smart device, you can remotely control your digital piano for even more convenience and flexibility. By presenting various parameters on-screen, this app allows you to make settings in a visual, more intuitive manner. For more details on “Smart Pianist,” refer to the following Yamaha web site.

https://www.yamaha.com/kbdapps/

For instructions on connecting the instrument to a smart device, Connection Wizard in “Smart Pianist” will guide you according to the operating condition and environment. To start the Connection Wizard, tap “ ” (Menu) located at the upper left of the screen to open the Menu display, and then tap “Instrument” → “Start Connection Wizard.”

NOTE:
This instrument does not support wireless connection. Please select “Cable” in the selection of the connection method to the Smart Pianist.

Panel Controls and Terminals

• [P] (Standby/On) switch.

For turning the power on or setting to standby.

• [MASTER VOLUME] knob .

For adjusting the volume of the entire sound.

CAUTION

Do not use this instrument at a high volume level for a long period of time, to avoid damaging your hearing.

•   [GRAND PIANO/FUNCTION] button
  For instantly calling up the Grand Piano 1 Voice.
• FUNCTION
  You can set various parameters by pressing a note on the keyboard while holding this button.
• [PHONES] jacks
  For connecting a set of standard stereo headphones.

CAUTION
Do not use headphones at a high volume for an extended period of time; doing so may cause hearing loss.

• [USB TO HOST] terminal
  For connecting to a computer or a smart device. For details on connections, refer to “Computer-related Operations” or “Smart Device Connection Manual” on the website.

NOTICE:
Use an AB type USB cable of less than 3 meters. USB 3.0 cables cannot be used.

• [TO PEDAL] jack .
  For connecting the pedal cord.
• DC IN jack…
  For connecting the AC adaptor.
• Soft Pedal (Left) .
  Pressing this pedal reduces the volume and slightly changes the timbre of notes.
• Sostenuto Pedal (Center) .
  Pressing this pedal after playing a note or notes (but before releasing your fingers) causes the pressed note(s) to sustain while subsequent notes can be played without sustain.

Damper Pedal (Right) ..
Pressing this pedal causes the notes you play to have a longer sustain. It can be used with the half pedal function.

1. P] (Standby/On) switch to turn the power on.

Setting Up

Key Cover

To open the key cover, lift the cover slightly, then push and slide it to the end. To close the key cover, gently slide the cover toward you.

CAUTION: Hold the cover with both hands when opening or closing it. Do not release it until it is fully opened or closed. Be careful to avoid catching fingers (yours or others, especially children’s) between the cover and main unit.

Music Rest

To raise the music rest:

To lower the music rest: Turning the Power On

1. Connect the plugs of the AC adaptor in the order shown in the illustration.
   Follow the order shown above in reverse when disconnecting the AC adaptor.
   WARNING
   • Use the specified adaptor  The use of other adaptors may result in irreparable damage to both the adaptor and the instrument.
   • When setting up the product, make sure that the AC outlet you are using is easily accessible. If some trouble or malfunction occurs, immediately turn the power off and disconnect the plug from the outlet.
   • When using the AC adaptor with a removable plug,
     • Make sure to keep the plug attached to the AC Using the plug alone can cause electric shock or fire.
     • If the plug is accidentally removed from the AC adaptor, never touch the metallic section when attaching the To avoid electric shock, short circuit or damage, also be careful that there is no dust between the AC adaptor and plug.
       The shape of the plug and outlet differ depending on the locale
2. Turn down the [MASTER VOLUME] knob to “MIN.”NOTICE
   Press only the [P] (Standby/On) switch when turning the power on. Any other operations, such as pressing the keys, buttons or pedals may cause the instrument to malfunction.
3. Press the [P] (Standby/On) switch to turn the power on. Adjust the volume as desired while playing the keyboard.
   NOTICE:
   Press only the [P] (Standby/On) switch when turning the power on. Any other operations, such as pressing the keys, buttons or pedals may cause the instrument to malfunction.
4. Press the [P] (Standby/On) switch againfor 1 second to turn off the power.
   The power lamp turns off.
   CAUTION
   Even when the [P] (Standby/On) switch is in the standby status, electricity is still flowing to the instrument at a minimum level. When not using the instrument for an extended period of time, be sure to unplug the power cord from the wall AC outlet.

Auto Power Off Function

To prevent unnecessary power consumption, this function automatically turns the power off if the instrument is not operated for 30 minutes.
Default setting: Enabled

Disabling Auto Power Off (simple method)

While holding down the A−1 key (the lowest key), press the [P] (Standby/On) switch to turn the instrument on.

To re-enable the Auto Power Off function,

Volume Limiter Function

When this function is on, the Master Volume does not increase even when the [MASTER VOLUME] knob is turned to the right from center. This allows you to protect your hearing when using the headphones or prevent loud sound from coming out of the speakers.
To turn on this function,

Maximum Volume (Center) The Master Volume does not increase even when the [MASTER VOLUME] knob is turned to the right from center.

Functions

You can call up a function by holding down the [GRAND PIANO / FUNCTION] button and pressing the specified key. For certain functions, changing the setting produces a confirmation sound.
Simply pressing the [GRAND PIANO / FUNCTION] button calls up the Grand Piano 1 Voice.

Smart Device App “Smart Pianist”

You can get even more enjoyment out of this instrument—with additional functions and highly intuitive controls—by connecting to the “Smart Pianist” smart device app. For details, see the website below. https://www.yamaha.com/kbdapps

Using the Pedals

 Damper Pedal (Right)

Pressing this pedal will sustain notes longer. Releasing this pedal immediately stops (damps) any sustained notes. This pedal also features a “half-pedal” function that creates partial sustain effects, depending on how far down you press the pedal.

When you press the damper pedal here, this note and the notes you play before you release the pedal sustain longer

NOTE:
When you press the damper pedal here, this note and the notes you play before you release the pedal sustain longer. If the damper pedal doesn’t work, make sure that the pedal cord is properly plugged into the main unit

Half-pedal function
This function allows you to vary the sustain length depending on how far the pedal is pressed. The farther down you press the pedal, the more the sound sustains. For example, if you press the damper pedal and all notes you are playing sound a bit murky and loud with too much sustain, you can release the pedal half way or higher to decrease the sustain (murkiness).

Damper Resonance
When only piano Voices  is selected, pressing the damper pedal activates the Damper Resonance effect to recreate the resonance of an acoustic piano’s strings.
NOTE: Damper Resonance cannot be used in Duo.

Sostenuto Pedal (Center)

Pressing this pedal while holding the notes will sustain the pressed notes (as if the Damper Pedal had been pressed), but all subsequently played notes will not be sustained. This makes it possible to sustain a chord or single low note, for example, while the other notes are played “staccato.”

When you press the sostenuto pedal here while holding the note, the note will sustain as long as you hold the pedal
NOTE:
While the sostenuto pedal is held, the organ and strings Voices sound continuously without decay after the notes have been released.

Soft Pedal (Left)

Pressing this pedal will reduce the volume and slightly change the timbre of the notes. The notes played before this pedal is pressed are not affected.

Pedal function in Duo In Duo, the pedal function changes as follows.

• Right Pedal: Damper pedal for the right-hand range.
• Center Pedal: Damper pedal for both the right- hand and left-hand ranges.
• Left Pedal: Damper pedal for the left-hand range.

Data List

VOICE LIST

Reverb Type List

  NOTE: In Dual, the Reverb Type for Voice 1 is called up.

Voice Demo Song List

The Demo Songs excluding original Songs are short rearranged excerpts from the original compositions. The original Demo Songs are Yamaha originals (© Yamaha Corporation).

Preset Song List

Touch Sensitivity

NOTE:This setting is disabled with some Voices, such as an organ

Keyboard Stand Assembly

Assembly Precautions

CAUTION

• Assemble the instrument using at least two people.
• Assemble the instrument on a hard and flat floor with ample space.
• Be sure to use the correct parts in the correct orientation, and assemble the instrument in accordance with the sequence given here.
• Keep small parts (such as screws) out of the reach of infants. Children may accidentally swallow them.
• Be sure to use only the included screws of specified sizes. Use of any other screws can cause damage or malfunction of the product.
• To disassemble the unit, reverse the assembly sequence given here.

Have a Phillips-head (+) screwdriver of the appropriate size ready.

Post-assembly checklist

• There are no unused parts.
• The instrument is stable even if you shake it.
• The pedal adjuster is firmly pressed against to the floor surface.
• Both the pedal cord and power cord are plugged securely into the correct jacks.

If there are any items above you haven’t confirmed, review the assembly procedure and correct any errors.

Assembly
You can watch a video of the assembly.

Scan the QR code at left or access the website below.
https://4wrd.it/ydp_assembly_video3

Check if you have all of the items indicated below.
NOTICE: Make sure to place the main unit on the polystyrene foam pads that have been removed from the packages. Position the pads so that they will not contact the speaker covers on the bottom of the main unit.

The adaptor may not be included, or may look different from the illustration above, depending on your particular area.

1. Align the side boards with each end of pedal box, and lightly tighten with flat head screws (6 × 20 mm) for temporary fastening
   These screws will be tightened securely later in step 3.
   
2. Attach the back board.
   Depending on the model, the surface color of one side of the back board may be different from the other side. In this case, position the back board so that the side facing the front (pedal side) matches the color of the main unit.
   
   • Place the back board on each foot of side boards.
   • Attach the top of the back board by temporarily fastening the thin screws (4 × 12 mm).
   • While pushing on the lower part of the side boards from the outside, secure the bottom ends of the back board using tapping screws (4 × 20 mm) in the order from outside to inside (1 → 2).
     2-4 Securely tighten the screws on the top of the back board that were attached in step 2-2.
3. Secure the pedal box
   Securely tighten the screws on the pedal box that were attached in step 1.
   
4. Set the main unit in place
   
   • Be sure to hold the bottom surface at least 10 cm inside from the edge of the main unit so that you do not pinch your hands.
   • Place the main unit on the side boards so that the front of the main unit and the side boards are aligned. Slide the main unit forward and insert the metal fittings on the bottom of the main unit into the metal fittings on the side boards.
     CAUTION:
     • Be careful not to pinch your hands or drop the main unit.
     • Do not hold anywhere other than the specified position.
5. Secure the main unit by tightening the thick screws (6 × 16 mm).
   
   
6. Connect the pedal cord plug and the power plug.
   
   • Insert the pedal cord plug to the [TO PEDAL] jack from the rear.
     Insert the plug until the metal part disappears from view.
     NOTICE:
     If it is not plugged in firmly, it may cause the pedals to not work.
   • Wind the cord holders around pedal cord to hold
     The cord holders are attached to the side board (L).
   • Insert the DC plug into the DC IN
     
7. Rotate the adjuster until it presses in firm contact with the floor surface.
   Make sure that the pedal box does not rattle or give way when you step on the pedals.
   After completing the assembly, please check the Post- assembly checklist.

Data Backup and Initializing

The following data will automatically be maintained as backup data even if you turn off the power.

Backup data
Metronome Volume, Metronome Beat, Touch Sensitivity, Tuning, Auto Power Off, Operation Confirmation Sound on/off, Volume Limiter on/off

To initialize the backup data:

While holding down the C7 key (right-most key), turn the power on to initialize the backup data to the factory initial settings.

NOTICE:
Never turn off the power while the initialization is being executed.
NOTE:
If this instrument somehow malfunctions or fails to operate properly, try executing the initialization

Troubleshooting

Specifications

• The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest manual, access the Yamaha website then download the manual file. Since specifications, equipment or separately sold accessories may not be the same in every locale, please check with your Yamaha dealer.

Information for users on collection and disposal of old equipment:
This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in accordance with your national legislation. By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. For more information about collection and recycling of old products, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items. For business users in the European Union: If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information. Information on Disposal in other Countries outside the European Union: symbol is only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal.

Important Notice:
U.S. LIMITED WARRANTY for Customers in the United States
For detailed information about this Yamaha product and warranty service,
please either visit the following website address (printable file is available at our website) or contact Customer Service at the address or telephone number identified below.
Website Address:
yamaha.i.o/YDPWarranty
Customer Service:
Yamaha Corporation of America
6600 Orangethorpe Avenue, Buena Park, CA 90620-1273
Telephone: 800-854-1569

Important Notice: Guarantee Information for customers in European Economic Area (EEA) and Switzerland
Important Notice: Guarantee Information for customers in EEA* and Switzerland
For detailed guarantee information about this Yamaha product, and Pan-EEA* and Switzerland warranty service, please either visit the website address below (Printable at our website) or contact the Yamaha representative office for your country. * EEA: European Economic Area
For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below.

CANADA
Yamaha Canada Music Ltd.
135 Milner Avenue, Toronto, Ontario M1S 3R1, Canada
Tel: +1-416-298-1311

U.S.A.
Yamaha Corporation of America
6600 Orangethorpe Avenue, Buena Park, CA 90620, U.S.A.
Tel: +1-714-522-9011

MEXICO
Yamaha de México, S.A. de C.V.Av. Insurgentes Sur 1647 Piso 9, Col. San José Insurgentes, Delegación Benito Juárez, CDMX,
C.P. 03900, México
Tel: +52-55-5804-0600

BRAZIL
Yamaha Musical do Brasil Ltda.
Praça Professor José Lannes, 40-Cjs 21 e 22, Brooklin Paulista Novo CEP 04571-100 – São Paulo – SP, Brazil
Tel: +55-11-3704-1377

ARGENTINA
Yamaha Music Latin America, S.A., Sucursal Argentina
Olga Cossettini 1553, Piso 4 Norte, Madero Este-C1107CEK,
Buenos Aires, Argentina
Tel: +54-11-4119-7000

PANAMA AND OTHER LATIN AMERICAN REGIONS/ CARIBBEAN REGIONS
Yamaha Music Latin America, S.A.
Edificio Torre Davivienda, Piso: 20
Avenida Balboa, Marbella, Corregimiento de Bella Vista, Ciudad de Panamá, Rep. de Panamá
Tel: +507-269-5311

THE UNITED KINGDOM/IRELAND
Yamaha Music Europe GmbH (UK) Sherbourne Drive, Tilbrook, Milton Keynes, MK7 8BL, U.K.
Tel: +44-1908-366700

GERMANY
Yamaha Music Europe GmbH
Siemensstrasse 22-34, 25462 Rellingen, Germany
Tel: +49-4101-303-0

SWITZERLAND/LIECHTENSTEIN
Yamaha Music Europe GmbH, Branch Switzerland in Thalwil
Seestrasse 18a, 8800 Thalwil, Switzerland
Tel: +41-44-3878080

AUSTRIA/CROATIA/CZECH REPUBLIC/ HUNGARY/ROMANIA/SLOVAKIA/ SLOVENIA
Yamaha Music Europe GmbH, Branch Austria
Schleiergasse 20, 1100 Wien, Austria
Tel: +43-1-60203900

POLAND
Yamaha Music Europe Sp.z o.o. Oddział w Polsce
Wielicka 52, 02-657 Warszawa, Poland
Tel: +48-22-880-08-88

BULGARIA
Dinacord Bulgaria LTD.
Bul.Iskarsko Schose 7 Targowski Zentar Ewropa 1528 Sofia, Bulgaria
Tel: +359-2-978-20-25

MALTA
Olimpus Music Ltd.
Valletta Road, Mosta MST9010, Malta
Tel: +356-2133-2093

NETHERLANDS/BELGIUM/ LUXEMBOURG
Yamaha Music Europe, Branch Benelux Clarissenhof 5b, 4133 AB Vianen, The Netherlands
Tel: +31-347-358040

FRANCE
Yamaha Music Europe
7 rue Ambroise Croizat, Zone d’activités de Pariest, 77183 Croissy-Beaubourg, France
Tel: +33-1-6461-4000

ITALY
Yamaha Music Europe GmbH, Branch Italy Via Tinelli N.67/69 20855 Gerno di Lesmo (MB), Italy
Tel: +39-039-9065-1

SPAIN/PORTUGAL
Yamaha Music Europe GmbH Ibérica, Sucursal en España
Ctra. de la Coruña km. 17,200, 28231 Las Rozas de Madrid, Spain
Tel: +34-91-639-88-88

GREECE
Philippos Nakas S.A. The Music House
19th klm. Leof. Lavriou 190 02 Peania – Attiki, Greece
Tel: +30-210-6686260

SWEDEN
Yamaha Music Europe GmbH Germany Filial Scandinavia
JA Wettergrensgata 1, 400 43 Göteborg, Sweden
Tel: +46-31-89-34-00

DENMARK
Yamaha Music Denmark,
Fillial of Yamaha Music Europe GmbH, Tyskland Generatorvej 8C, ST. TH., 2860 Søborg, Denmark
Tel: +45-44-92-49-00

FINLAND
F-Musiikki Oy
Antaksentie 4 FI-01510 Vantaa, Finland
Tel: +358 (0)96185111

NORWAY
Yamaha Music Europe GmbH Germany – Norwegian Branch
Grini Næringspark 1, 1332 Østerås, Norway
Tel: +47-6716-7800

ICELAND
Hljodfaerahusid Ehf.
Sidumula 20
IS-108 Reykjavik, Iceland
Tel: +354-525-5050

CYPRUS
Nakas Music Cyprus Ltd.
Nikis Ave 2k 1086 Nicosia
Tel: + 357-22-511080

Major Music Center
21 Ali Riza Ave. Ortakoy P.O.Box 475 Lefkoşa, Cyprus
Tel: (392) 227 9213

RUSSIA
Yamaha Music (Russia) LLC.
Room 37, entrance 7, bld. 7, Kievskaya street,
Moscow, 121059, Russia
Tel: +7-495-626-5005

OTHER EUROPEAN REGIONS
Yamaha Music Europe GmbH
Siemensstrasse 22-34, 25462 Rellingen, Germany
Tel: +49-4101-303-0

Yamaha Music Gulf FZE
JAFZA-16, Office 512, P.O.Box 17328,
Jebel Ali FZE, Dubai, UAE
Tel: +971-4-801-1500

TURKEY
Yamaha Music Europe GmbH
Merkezi Almanya Türkiye İstanbul Şubesi Mor Sumbul Sokak Varyap Meridian Business 1.Blok No:1
113-114-115
Bati Atasehir Istanbul, Turkey
Tel: +90-216-275-7960

ISRAEL
RBX International Co., Ltd.
P.O Box 10245, Petach-Tikva, 49002