Nokia Comm Band Plus Headset User Guide

Comm Band +
CB-201 
User Guide 

What‘s in the box

• Headset
• USB Type-C cable
• Quick start guide
• Headphone pouch
• Microphone windscreen

Product Overview

Get started

1.1 Fully charge the headset before the first use.
It is recommended to recharge your device every 3 months even if it is not used.

Wearing

2.1 The microphone can be worn on the left or right side.
2.2 Adjust the headband for the best fit.
2.3 Rotate boom mic arm back and forth for wearing the left or right side.

Pair and connect with Bluetooth

3.1 Pairing with the device
3.1a Turning on and pairing: Press the power button for 2 seconds to turn it ON. When the LED indicator light flashes blue and red alternately the headset is ready to connect with your Bluetooth® device.
3.1b Connecting with your Bluetooth device: Turn on Bluetooth on your device and choose “Nokia CB-201” from the Bluetooth menu to connect.

During the connection process, the LED indicator light on the headset will flash blue and red alternately.

The LED indicator light will flash blue every 10 seconds when the headset is successfully connected via Bluetooth.
3.2 After the initial pairing, the headset will automatically connect with your Bluetooth device whenever it is powered on.
3.3 The headset will automatically power off if there is no Bluetooth connection within 5 minutes.

3.4 Pairing mode

i) Turn off the headset  (Press and hold the power button for 5 seconds.)
ii) When the headset is turned off. Press and hold the power button for 5s for pairing mode.
iii) When the LED indicator light flashes blue and red alternately, the headset is ready to connect with your Bluetooth device.
The headset will automatically power off if there is no Bluetooth connection within 5 minutes.

Multipoint connection

The headset can connect to two devices and enable answering calls on either device.
4.1 Pair devices separately (see 3.4).
i) Pair with the first device and disconnect.
ii) Pair with the second device.
iii) On the first device, reconnect to the headset.

4.2 Your headset will monitor both devices and you can answer to call from either one.

Button controls

In-call mode
The LED indicator light will turn on while having a call conversation, and people around you will recognize that you’re not to be disturbed.

5.1 Low latency mode (gaming & video mode)

Press the power button/ MFB (Multifunctional button) 4 times to toggle between Low latency mode > OFF.

• Low latency mode will consume more battery and total playtime will be 20% lesser.
• When Low latency mode is ON, the reception range will reduce to 5 meter
• The LED indicator light will flash blue twice every 10 seconds.

5.2 Reset to the original settings:
i) Press both the MFB button and volume- for 5 seconds
ii) LED indicator light will flash purple when the headset is reset.

Mic arm adjustment

Microphone windscreen

Apply the microphone windscreen to reduce wind or breathing noise.

Product and safety information

Remote control functions may vary depending on the model of your device and application. Since devices with Bluetooth wireless technology communicate using radio waves, they do not need to be in a direct line of sight. Bluetooth devices must, however, be within 10 meters (33 feet) of each other, although the connection may be subject to interference from obstructions such as walls or from other electronic devices.
Frequency Band: 2400 MHz – 2480 MHz
Maximum Radio Frequency Power: -6~+4dBm

For your safety

Take care of your device
Handle your device with care. The following suggestions help you keep your device operational.

• Keep the device dry. Precipitation, humidity, and all types of liquids or moisture can contain minerals that corrode electronic circuits.
• Do not use or store the device in dusty or dirty areas.
• Do not store the device in high temperatures. High temperatures may damage the device or battery.
• Do not store the device in cold temperatures. When the device warms to its normal temperature, moisture can form inside the device and damage it.
• Do not open the device other than as instructed in the user guide.
• Do not drop, knock, or shake the device or the battery. Rough handling can break it.
• Only use a soft, clean, dry cloth to clean the surface of the device.
• Do not paint the device. Paint can prevent proper operation.

Recycle
Always return your used electronic products, batteries, and packaging materials to dedicated collection points. This way you help prevent uncontrolled waste disposal and promote the recycling of materials. Electrical and electronic products contain a lot of valuable materials, including metals (such as copper, aluminum, steel, and magnesium) and precious metals (such as gold, silver, and palladium). All materials of the device can be recovered as materials and energy.

Crossed-out wheelie bin symbol
The crossed-out wheelie bin symbol on your product, battery, literature, or packaging reminds you that all electrical and electronic products and batteries must be taken to separate collections at the end of their working life. Do not dispose of these products as unsorted municipal waste: take them for recycling. For info on your nearest recycling point, check with your local waste authority.

Battery info
Your device has an internal, non-removable, rechargeable battery. Do not attempt to remove the battery, as you may damage the device. The battery can be charged and discharged hundreds of times, but it will eventually wear out. Charging time can vary depending on device capability.

Battery Safety
If left unused, a fully charged battery will lose its charge over time. Always keep the battery between 15°C and 25°C (59°F and 77°F) for optimal performance. Extreme temperatures reduce the capacity and lifetime of the battery. A device may temporarily stop working if its battery is too hot or too cold.
Do not dispose of batteries in a fire as they may explode. Obey local regulations. Recycle when possible. Do not dispose of as household waste.
Use the battery and charger for their intended purposes only. Improper use or use of unapproved or incompatible batteries or chargers may present a risk of fire, explosion, or another hazard, and may invalidate any approval or warranty. If you believe the battery or charger is damaged, take it to a service center or your local shop before continuing to use it. Never use a damaged battery or charger. Only use the charger indoors. Do not charge your device during a lightning storm.

Implanted medical devices
To avoid potential interference, manufacturers of implanted medical devices recommend a minimum separation of 15.3 centimeters (6 inches) between a wireless device and the implanted medical device. Persons who have such devices should:

• Always keep the wireless device more than 15.3 centimeters (6 inches) from the medical device.
• Do not carry the wireless device in a breast pocket.
• Switch the wireless device off if there is any reason to suspect that interference is taking place.
• Follow the manufacturer’s directions for the implanted medical device.

If you have any questions about using your wireless device with an implanted medical device, consult your health care provider.

Copyrights and other notices
The availability of products, features, apps and services may vary by region. For more info, contact your dealer or your service provider. This device may contain commodities, technology, or software subject to export laws and regulations from the US and other countries. Diversion contrary to law is prohibited.
The contents of this document are provided “as is”. Except as required by applicable law, no warranties of any kind, either express or implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose, are made in relation to the accuracy, reliability, or contents of this document. HMD Global reserves the right to revise this document or withdraw it at any time without prior notice.
Reproduction, transfer, or distribution of part or all of the contents in this document in any form without the prior written permission of HMD Global is prohibited. HMD Global operates a policy of continuous development. HMD Global reserves the right to make changes and improvements to any of the products described in this document without prior notice.
Manufacturer and importer in EU: HMD Global Oy, Bertel Jungin aukio 9, 02600 Espoo, Finland. HMD Global Privacy Policy, available at http://www.nokia.com/phones/privacy, applies to your use of the device.
In the unlikely event that this product is faulty, please return it to the store where you purchased it with your proof of purchase. For more information on this or other products please visit http://www.nokia.com/phones/support.
© 2022 HMD Global. All rights reserved. HMD Global Oy is the exclusive licensee of the Nokia brand for phones & tablets. Nokia is a registered trademark of Nokia Corporation.
The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by HMD Global is under license.

Declaration of conformity
Hereby, HMD Global Oy declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. A copy of the Declaration of Conformity can be found at: www.nokia.com/mobiledeclaration-of-conformity.

FCC Notice to users
The following statement applies to all products that bear the FCC logo and/or FCC ID on the product label.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. See 47 CFR Sec. 15.105(b).
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation. See 47 CFR Sec. 15.19(a)(3). HMD Global has not approved any changes or modifications to this device by the user.

Any changes or modifications could void the user’s authority to operate the equipment. See 47 CFR Sec. 15.21