Makita EN410MP Hedge Trimmer Attachment Instruction Manual

Hedge Trimmer Attachment
EN410MP

SPECIFICATIONS

• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.

Approved power unit

WARNING: Never use the attachment with the non-approved power unit. The non-approved combination may cause serious injury.
This attachment is approved to use only with the following power unit(s):

• (Multi-Function Power Head) EX2650LH
• (Cordless Multi-Function Power Head)
  BUX360, BUX361, BUX362, UX360D, UX361D, UX362D, DUX60, XUX01, DUX18, XUX02, UX01G, GUX01

Approved attachment

WARNING: Never use a non-approved attachment. Non-approved combinations may cause serious injury.
This attachment is approved to use only with the following attachment(s):

• (Shaft extension attachment) LE400MP

Symbols

The followings show the symbols which may be used for the equipment.
Be sure that you understand their meaning before use.

Intended use

This attachment is designed for only the purpose of trimming shrubs and hedges in conjunction with an approved power unit. Never use the attachment for another purpose. Abusing the attachment may cause serious injury.

EC Declaration of Conformity

For European countries only
We as the manufacturers: Makita Europe N.V., Business address: Jan-Baptist Vinkstraat 2 3070 Kortenberg BELGIUM. Authorize Hiroshi Tsujimura for the compilation of the technical file and declare under our sole responsibility that the product(s);
Designation: Hedge Trimmer Attachment. Designation of Type(s): EN410MP.
Fulfills all the relevant provisions of 2006/42/EC and also fulfills all the relevant provisions of the following EC/EU Directives: 2000/14/EC and are manufactured in accordance with the following Harmonised Standards: EN ISO 10517:2019, EN 62841-4-2:2019.
Place and date of declaration: Kortenberg, Belgium. 1. 5. 2022
Responsible person: Hiroshi Tsujimura, Director – Makita Europe N.V.

Declaration of Conformity (For the UK)

For the UK only
We as the manufacturers: Makita Europe N.V., Business address: Jan-Baptist Vinkstraat 2 3070 Kortenberg BELGIUM. Authorize Hiroshi Tsujimura for the compilation of the technical file and declare under our sole responsibility that the product(s);
Designation: Hedge Trimmer Attachment. Designation of Type(s): EN410MP.
Fulfills all the relevant provisions of S.I. 2008/1597 (as amended) and also fulfills all the relevant provisions of the following UK
Regulations: S.I. 2001/1701 (as amended) and are manufactured in accordance with the following Designated Standards: EN ISO 10517:2019, EN 62841-4-2:2019.
Place and date of declaration: Kortenberg, Belgium. 1. 5. 2022
Responsible person: Hiroshi Tsujimura, Director – Makita Europe N.V.
Importer: Makita (UK) Limited, Michigan Drive, Tongwell, Milton
Keynes, Buckinghamshire, MK15 8JD, UK

SAFETY WARNINGS

Hedge trimmer safety warnings

1. Keep all parts of the body away from the blade. Do not remove cut material or hold material to be cut when blades are moving. Blades continue to move after the switch is turned off. A moment of inattention while operating the hedge trimmer may result in serious personal injury.
2. Carry the hedge trimmer by the handle with the blade stopped and take care not to operate any power switch. Proper carrying of the hedge trimmer will decrease the risk of inadvertent starting and resultant personal injury from the blades.
3. When transporting or storing the hedge trimmer, always fit the blade cover. Proper handling of the hedge trimmer will decrease the risk of personal injury from the blades.
4. When clearing jammed material or servicing the unit, make sure all power switches are off and the battery pack is removed or disconnected. Unexpected actuation of the hedge trimmer while clearing jammed material or servicing may result in serious personal injury.
5. Hold the hedge trimmer by insulated gripping surfaces only, because the blade may contact hidden wiring. Blades contacting a “live” wire may make exposed metal parts of the hedge trimmer “live” and could give the operator an electric shock.
6. Keep all power cords and cables away from the cutting area. Power cords or cables may be hidden in hedges or bushes and can be accidentally cut by the blade.
7. Do not use the hedge trimmer in bad weather conditions, especially when there is a risk of lightning. This decreases the risk of being struck by lightning.

Extended-reach hedge trimmer safety warnings

1. To reduce the risk of electrocution, never use the extended-reach hedge trimmer near any electrical power lines. Contact with or use near power lines may cause serious injury or electric shock resulting in death.
2. Always use two hands when operating the extended-reach hedge trimmer. Hold the extended-reach hedge trimmer with both hands to avoid loss of control.
3. Always use head protection when operating the extended-reach hedge trimmer overhead. Falling debris can result in serious personal injury.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: Read all safety warnings and all instructions in this booklet and the instruction manual of the power unit.
Failure to follow the warnings and instructions may result in electric shock, fire, and/or serious injury.
WARNING: Save all warnings and instructions for future reference.
The term “hedge trimmer” and “equipment” in the warnings and precautions refer to the combination of the attachment and the power unit. The term “motor” in the warnings and precautions refers to the engine or electric motor of the power unit.

General precautions

1. Before starting the hedge trimmer, read this booklet and the instruction manual of the power unit to become familiar with the handling of the hedge trimmer.
2. Do not lend the attachment to a person with insufficient experience or knowledge regarding the handling of hedge trimmers.
3. When lending the attachment, always attach this instruction manual.
4. Do not allow children or young persons under 18 years old to use the hedge trimmer. Keep them away from the hedge trimmer.
5. Handle the hedge trimmer with the utmost care and attention.
6. Never use the hedge trimmer after consuming alcohol or drugs, or if feeling tired or ill.
7. Never attempt to modify the attachment. 8. Follow the regulations about handling hedge trimmers in your country.

Personal protective equipment
► Fig.1

1. Wear a safety helmet, protective goggles, and protective gloves to protect yourself from flying debris or falling objects.
2. Wear ear protection such as ear muffs to prevent hearing loss.
3. Wear proper clothing and shoes for safe operation, such as a work overall and sturdy, non-slip shoes. Do not wear loose clothing or jewelry. Loose clothes, jewelry, or long hair can be caught in moving parts.
4. When touching blades or adjusting the blade angle, wear protective gloves. Blades can cut bare hands severely.

Work area safety
WARNING: Keep the hedge trimmer away from electric lines and communication cables. Touching or approaching high-voltage lines with a hedge trimmer can result in death or serious injury. Watch power lines and electrical fences around the work area before starting operation.
WARNING: The use of this product can create dust-containing chemicals that may cause respiratory or other illnesses. Some examples of these chemicals are compounds found in pesticides, insecticides, fertilizers, and herbicides. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well-ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

1. Operate the hedge trimmer under good visibility and daylight conditions only. Do not operate the hedge trimmer in darkness or fog. 2. Start and operate the engine only outdoors in a well-ventilated area. Operation in a confined or poorly ventilated area can result in death due to suffocation or carbon monoxide poisoning. 3. During operation, never stand on an unstable or slippery surface or a steep slope. During the cold season, beware of ice and snow and always ensure secure footing. 4. During operation, keep bystanders or animals at least 15 m away from the hedge trimmer. Stop the motor as soon as someone approaches. 5. Before the operation, examine the work area for wire fences, stones, or other solid objects. They can damage the blades.

Putting into operation

1. Before assembling or adjusting the equipment, switch off the motor and remove the spark plug cap or the battery cartridge.
2. Before assembling the blades or adjusting the cutting angle, wear protective gloves.
3. Before starting the motor, inspect the equipment for damages, loose screws/nuts, or improper assembly. Replace if the blades are cracked, bent, or damaged. Check all control levers and switches for easy action. Clean and dry the handles.
4. Never attempt to start the motor if the equipment is damaged or not fully assembled. Otherwise, serious injury may result.
5. Adjust the shoulder harness and hand grip to suit the operator’s body size.

Operation

1. In the event of an emergency, switch off the motor immediately.
2. If you feel any unusual condition (e.g. noise, vibration) during operation, switch off the motor. Do not use the hedge trimmer until the cause is recognized and solved.
3. The blades continue to move for a short period after releasing the throttle trigger or switching off the motor. Don’t rush to contact the blades.
4. With the engine running only at idle, attach the shoulder harness.
5. During operation, use the shoulder harness. Keep the hedge trimmer on your right side firmly.
   ► Fig.2
6. Hold the front handle with the left hand and the rear grip with the right hand, no matter whether you are a right-hander or left-hander. Wrap your fingers and thumbs around the handles.
7. Never attempt to operate the equipment with one hand. Loss of control may result in serious or fatal injury. To reduce the risk of cut injuries, keep your hands and feet away from the blades.
8. Do not overreach. Keep proper footing and balance at all times. Watch for hidden obstacles such as tree stumps, roots, and ditches to avoid stumbling. Clear fallen branches and other objects away.
9. Never work on a ladder or tree to avoid loss of control.
10. Do not hold the machine above shoulder height.
11. During operation, never hit the blades against hard obstacles such as stones and metals. Take particular care when cutting hedges next to or against wire fences. When working close to the ground, make sure that no sand, grit, or stones get between the blades.
12. If the blades come into contact with stones or other solid objects, stop the motor immediately and check the blades for damage after removing the spark plug or the battery cartridge. Replace the blades if damaged.
13. If thick branches get jammed in the blades, immediately switch off the motor, put the hedge trimmer down, and then remove the obstruction after removing the spark plug or the battery cartridge. Check the blades for damage before using the equipment again.
14. Never touch or approach the blades while they are moving. Blades can cut your finger easily. When handling the blades or adjusting the blade angle, stop the motor and remove the spark plug cap or the battery cartridge.
15. Accelerating the motor with the blades blocked increases the load and will damage the motor and/or clutch.
16. Check the cutting blades frequently during operation for cracks or blunt edges. Before the inspection, switch off the motor and wait until the blades stop completely. Replace damaged or dull blades immediately, even if they have only superficial cracks.
17. If the equipment gets heavy impact or falls, check the condition before continuing work. Check the fuel system for fuel leakage and the controls and safety devices for malfunction. If there is any damage or doubt, ask our authorized service center for the inspection and repair.
18. Do not touch the gear case. The gear case becomes hot during operation.
19. Take a rest to prevent loss of control caused by fatigue. We recommend taking a 10 to 20-minute rest every hour.
20. When you leave the equipment, even if it is a short time, always switch off the engine or remove the battery cartridge. The equipment unattended with the engine running may be used by an unauthorized person and cause a serious accident.
21. Before cutting, pull the throttle lever fully to achieve the maximum speed.
22. Follow the instruction manual of the power unit for proper use of the control lever and switch.
23. During or after the operation, do not put the hot equipment onto dry grass or combustible materials.

Transport

1. Before transporting the equipment, switch off the motor and remove the spark plug cap or battery cartridge. Always fit the blade cover during transportation.
2. When carrying the equipment, carry it in a horizontal position by holding the shaft. Keep the hot muffler away from your body.
3. When transporting the equipment in a vehicle, properly secure it to avoid turnover. Otherwise, fuel spillage and damage to the equipment and other baggage may result.

Maintenance

1. Before doing any maintenance or repair work or cleaning the equipment, always switch off the motor and remove the spark plug cap or the battery cartridge. Wait until the motor gets cold.
2. To reduce the risk of fire, never service the equipment in the vicinity of the fire.
3. Always wear protective gloves when handling the blades.
4. Always clean dust and dirt off the equipment. Never use gasoline, benzene, thinner, alcohol, or the like for the purpose. Discoloration, deformation, or cracks of the plastic components may result.
5. After each use, tighten all screws and nuts, except for the carburetor adjustment screws.
6. Keep the cutting tool sharp. If the cutting blades have become blunt and cutting performance is poor, ask our authorized service center to sharpen the blades.
7. Never repair bent or broken blades by straightening or welding. It may cause parts of the blades to come off and result in serious injury. Contact our authorized service center for Makita genuine blades to replace them.
8. Do not attempt any maintenance or repair not described in this booklet or the instruction manual of the power unit. Ask our authorized service center for such work.
9. Always use Makita genuine spare parts and accessories only. Using parts or accessories supplied by a third party may result in equipment breakdown, property damage, and/or serious injury.
10. Request our authorized service center to inspect and maintain the hedge trimmer at regular intervals.

Storage

1. Before storing the equipment, perform full cleaning and maintenance. Fit the blade cover. 2. Store the equipment in a dry and high or locked location out of reach of children.
2. Do not prop the equipment against something, such as a wall. Otherwise, the hedge trimmer may fall suddenly and cause an injury.

First aid

1. Always have a first-aid kit close by. Immediately replace any item taken from the first aid kit.
2. When asking for help, give the following information:
   — Place of the accident
   — What happened
   — Number of injured persons
   — Nature of the injury
   — Your name

PARTS DESCRIPTION

► Fig.3

ASSEMBLY

WARNING: Before assembling or adjusting the equipment, switch off the motor and remove the spark plug cap or the battery cartridge. Otherwise, blades or other parts may move and result in serious injury.
WARNING: Before handling or working around blades, wear protective gloves and put the blade cover onto the blades. Otherwise, the blades can cut bare hands severely.
WARNING: When assembling or adjusting the equipment, always put it down. Assembling or adjusting the equipment in an upright position may result in serious injury.
WARNING: Follow the warnings and precautions in the chapter “Safety precautions” and the instruction manual of the power unit.
WARNING: Before operating the equipment, make sure that the lock lever is tightened.

Mounting the attachment to a power unit

To mount the attachment to a power unit, follow the steps below.

1. Make sure that the lock lever is not tightened.
2. Align the pin with the arrow mark.
3. Insert the shaft into the drive shaft of the power unit until the position line and the release button pops up.
4. Tighten the lock lever firmly as shown.
   To remove the attachment, loosen the lock lever by turning the lock lever opposite direction, and press the lock button and withdraw the shaft.
   ► Fig.4: 1. Lock lever 2. Pin 3. Arrow mark 4. Position line 5. Release button

NOTICE: Do not tighten the lock lever without the shaft of the attachment inserted. Otherwise, the lock lever may tighten the entrance of the drive shaft too much and damage it.

OPERATION

WARNING: If the blades move at idle, adjust the idle speed of the engine down. Otherwise, you cannot stop the blades with the throttle off and it may cause serious injury.
WARNING: Follow the warnings and precautions in the chapter “IMPORTANT SAFETY INSTRUCTIONS” and the instruction manual of the power unit.

Horizontal cut

When trimming hedges horizontally, follow the steps below.

1. Pull the throttle lever fully.
2. Apply the blades to the hedge at an angle of 15° to 30°.
3. Trim the hedge with a right to left swinging movement.
   ► Fig.5

Vertical cut

When trimming hedges vertically, follow the steps below.

1. Pull the throttle lever fully.
2. Apply the blades to the hedge parallel to each other.
3. Trim the hedge from the bottom upwards with a swinging movement.
   ► Fig.6

MAINTENANCE

WARNING: Before inspecting or maintaining the equipment, switch off the motor and remove the spark plug cap or the battery cartridge. Otherwise, blades or other parts may move and result in serious injury.
WARNING: Before handling or working around blades, wear protective gloves and put the blade cover onto the blades. During the assembly or adjustment, your fingers may contact with blades and it may cause serious injury.
WARNING: When inspecting or maintaining the equipment, always put the equipment down. Assembling or adjusting the equipment in an upright position may result in serious injury.
WARNING: Follow the warnings and precautions in the chapter “IMPORTANT SAFETY INSTRUCTIONS” and the instruction manual of the power unit.

Inspecting blades

Check the blades daily for damage, crack, and dull edges. Ask our authorized service center to replace damaged blades or sharpen dull blades.

Adjusting the blade clearance

The upper/lower blades wear out gradually after operations. If you cannot get a clean cut through the blades are sharp enough, adjust the clearance as follows.
The tightness of the hex bolt decides the clearance of the blades.
The nut holds the hex bolt with certain tightness. Too loose clearance causes a blunt cut, but too tight clearance causes unnecessary heat and sooner worn-out of the blades.

1. Loosen the nuts with a wrench.
2. Tighten the hex bolts lightly till they stop. And then, screw them back a quarter to half turn each to gain the necessary clearance.
3. Hold the hex bolts and tighten the nuts.
4. Apply light oil to the friction surface of the blades.
5. Start the motor and operate the throttle on and off for a minute.
6. Measure the time necessary for the blades to stop after releasing the throttle. If it is two seconds or longer, switch off the motor and repeat step 1 to 6.
7. Switch off the motor and touch the blade surface. If they are not too hot to touch, you have made a proper adjustment. If they are too hot to touch, turn the hex bolts back a little and repeat steps 5 to 7.
   ► Fig.7: 1. Nut 2. Hex bolt 3. Plate 4. Blade guard 5. Upper blade 6. Lower blade

Lubricating moving parts

NOTICE: Follow the instruction on the frequency and amount of grease supplied. Otherwise, insufficient lubrication may damage moving parts.
► Fig.8

Gear case:
Apply grease every 25 working hours.

1. The grease hole locates under the bolt. Remove the bolt to lubricate.
2. Add approx. 5 g (7 ccs) of grease to the grease hole.
3. Return the bolt after lubrication.
   ► Fig.9: 1. Grease hole

NOTE: After filling the correct amount of grease, grease will come out a bit from the base of the blade during the first operation.

Drive axle:
Apply grease every 25 working hours. Overall inspection

• Tighten loose bolts, nuts, and screws.
• Check for damaged parts and blades. Ask our authorized service center to replace them if necessary.

Storage

WARNING: Follow the warnings and precautions in the chapter “IMPORTANT SAFETY INSTRUCTIONS” and the instruction manual of the power unit.
When storing the hedge trimmer attachment separated from the power unit, put the cap onto the end of the shaft.
► Fig.10

MAINTENANCE INTERVAL

TROUBLESHOOTING

OPTIONAL ACCESSORIES

CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.

If you need any assistance with more details regarding these accessories, ask your local Makita Service Center.

• Blade set

NOTE: Some items in the list may be included in the tool package as standard accessories. They may differ from country to country.

Makita Europe N.V.
Jan-Baptist Vinkstraat 2,
3070 Kortenberg, Belgium
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi 446-8502 Japan
www.makita.com
885480F996
20220121