GE 45117 Personal Security Deluxe Door Alarm User Manual

GE 45117 Personal Security Deluxe Door Alarm

Low Battery Indicator

The alarm unit has a low battery circuit. When the batteries reach a low level, the indicator light will flash slowly. Average battery life for typical usage is up to one year.

INSTALLING BATTERIES

The keypad controlled door alarm requires three (3) AAA Alkaline batteries (not included).

To install the batteries:

Remove screw from battery compartment door located on back of the unit. Slide off the door in the direction of the arrow.
Insert three (3) AAA batteries noting the polarity diagram inside the battery compartment.
Replace door and secure screw.

CREATING YOUR PERSONAL ALARM CODE

The keypad allows you to set a personal 4- digit code for arming and disarming the alarm.

Remove screw from battery compartment door located on back of the unit. Slide off the door in the direction of the arrow.
Press the LEARN button.
The red light on the front of the alarm will blink for 15 seconds. During this time, input your 4-digit code. A beep will conﬁrm each input. The unit will ﬂash a green light 3 times to conﬁrm the new 4-digit code has been saved.
Replace cover and secure screw.

INSTALLATION

Select desired location for alarm. The alarm is designed to mount to the door frame or to the door itself. Use either the provided screws (for permanent mounting) or double-sided tape (for temporary mounting). The recommended location is the back of the door, with the magnet mounted to the door frame. Mounting the alarm to the door ensures that the alarm will not be damaged by opening and closing the door.
Note that the magnet may be mounted to either side of the alarm as long as the arrows line up.
IMPORTANT: Whether mounting to the door or door frame, the gap distance between the alarm and magnet must be 1/2” or less.
Attach the mounting plate to the back of the alarm. Peel the protective covering from one side of the double-sided tape and then apply to mounting plate. Remove protective covering from the back side of the double-sided tape and lightly mount the alarm in the desired position. Make sure the surface you are mounting to is clean and dry. For best results, clean the mounting surface with a mixture of 50% isopropyl alcohol and 50% water.
Do not apply ﬁrm pressure until location is ﬁnal.
NOTE: When mounting to a door frame, the mounting plate mounts off-center to the left or right in order to position alarm closest to the edge of the door.
Using double-sided tape, lightly attach the magnet to the opposite edge next to the alarm. Line up the arrows of the alarm and the magnet. Ensure the distance between the two pieces is 1/2” or less. To test the gap distance, slide the ALARM/CHIME switch to CHIME and open the door. If chime sounds, then the gap distance is correct. If it does not sound, move either the alarm or magnet closer so that gap distance is 1/2” or less.
Once you have conﬁrmed the correct positioning of the magnet and alarm, lift the alarm off the mounting plate and apply ﬁrm pressure directly to the plate itself. Once secured, reattach the alarm to the mounting plate.
Apply ﬁrm pressure to the magnet to secure its position as well.

OPERATING IN THE ALARM MODE

Locate ALARM/CHIME switch on right side of the alarm unit.
Slide switch to ALARM position.
Choose HOME or AWAY on the left side of the alarm unit.

HOME MODE
In HOME mode, the alarm will sound when the gap between the alarm and the magnet is greater than 1/2” (i.e. the door is opened).

AWAY MODE
In AWAY mode, there will be a 45 second exit delay before the unit is armed. The alarm’s indicator light will ﬂash red quickly, alerting you that the unit has been activated and has begun the 45-second count down. The delay allows time for you to leave the protected area without triggering the alarm. When returning to the protected area, there is a 30 second delay to allow time to enter 4-digit code before the alarm will sound.

Arming the Alarm:

Arm the alarm by pressing your 4-digit code. When the 4 digit code is entered correctly the unit will ﬂash a green light once. NOTE: if the 4 digit code is entered incorrectly, the unit will sound a higher tone and ﬂash red 3 times.
Disarming the Alarm:

Enter your 4-digit code to disarm the alarm. When the fourth digit of your code is entered, the unit will respond with two tones and will ﬂash a green light twice.
Enter the correct code anytime after the alarm has sounded to deactivate. NOTE: When testing, a cloth can be used to cover the alarm to reduce risk of hearing damage.

Incorrect Code
If an incorrect code is entered, the unit will sound a louder beep and will ﬂash red 3 times. Re-enter the correct code after the light stops ﬂashing.

OPERATING IN THE CHIME MODE

Locate ALARM/CHIME switch on right side of unit.
Slide switch to CHIME mode.

Activating the Chime:
The chime will now sound immediately if the distance between the alarm and magnet is greater than 1/2” (i.e. the door is opened).

Deactivating the Chime:
To deactivate the chime slide ALARM/ CHIME switch to ALARM position.

CARE AND MAINTENANCE

To clean the alarm housing, use a soft cloth slightly dampened with water and wipe dry. Do not use chemical agents as this may damage and discolor the unit.

WARNING

Limitations of Alarm Products

This product should be tested periodically to make sure it is working properly. The product, if used properly, may reduce the risk of burglary, robbery, or other adverse events. However, JASCO is not an insurer, this product is neither insurance nor a guarantee that such an event will be prevented, and users should protect themselves with proper insurance. JASCO makes no representation that this product cannot be compromised or circumvented, that it will provide an adequate warning, or that it will prevent any personal injuries, property damage, or other losses. Like any alarm product, including expensive commercial systems, it may be bypassed, it is subject to compromise, and it may
fail to warn for a variety of reasons, including, but
not limited to: improper installation or positioning; improper maintenance; tampering; dead or improperly installed batteries; sensing limitations; component failures; receivers; for infrared products, intrusions may be outside of a product’s designed range
and certain environmental conditions may impact performance and audible alarm signals may be outside of hearing range, muted by doors, walls, and ﬂoors, unheard by deep sleepers or the hearing-impaired, or overwhelmed by other sounds.

Risk of personal injury

Prolonged exposure to alarm siren may cause permanent hearing loss
Battery Warning
Remove batteries before storing the Alarm for extended periods
Batteries may leak harmful liquids or ignitable materials or explode causing injury and product damage
Do not mix old and new or other battery types
Replace all batteries at the same time
Replace fully discharged batteries immediately

For indoor use only; do not use in wet locations.
This Jasco product comes with a 90 day limited warranty. Please contact Customer Service at
800- 654-8483 between 7:30AM—5:00PM CST or via our website (www.jascoproducts.com) if the unit should prove defective within the warranty period.

is a trademark of the General Electric Company and is used under license to Jasco Products Company LLC, 10 E. Memorial Road, Oklahoma City, OK 73114.

FCC RULES

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.

FCC NOTE: The manufacturer is not responsible for
any radio or TV interference caused by unauthorized modiﬁcations to this equipment. Such modiﬁcations could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found
to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Download

GE 45117 Personal Security Deluxe Door Alarm User Manual

Was this manual helpful?