Sharp 8M-B32C1 31.5 Inch IPS 8K Desktop Monitor User Manual

8M-B32C1
LCD MONITOR
SETUP MANUAL

IMPORTANT INFORMATION

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

CAUTION
THE RISK OF ELECTRIC SHOCK DOES NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER. NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with the arrowhead symbol, within a triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

To maintain compliance with EMC regulations, use shielded cables to connect to the following terminals: HDMI input terminal, DisplayPort input terminal, and USB port.

DEAR SHARP CUSTOMER

Thank you for your purchase of a SHARP LCD product. To ensure safety and many years of trouble-free operation of your product, please read the Safety Precautions carefully before using this product.

SAFETY PRECAUTIONS

Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can result in electric shock and/or fire. In order to prevent potential danger, please observe the following instructions when installing, operating, and cleaning the product. To ensure your safety and prolong the service life of your LCD product, please read the following precautions carefully before using the product.

  1. Read instructions — All operating instructions must be read and understood before the product is operated.
  2. Keep this manual in a safe place — This safety and operating instructions must be kept in a safe place for future reference.
  3. Observe warnings — All warnings on the product and in the instructions must be observed closely.
  4. Follow instructions — All operating instructions must be followed.
  5. Cleaning — Unplug the power cord from the power outlet before cleaning the product. Use a dry cloth to clean the product.
    Do not use liquid cleaners or aerosol cleaners. Do not use dirty clothes. Doing so may damage the product.
  6. Attachments — Do not use attachments not recommended by the manufacturer. The use of inadequate attachments can result in accidents.
  7. Water and moisture — Do not use the product near water. Do not install the product in a place where water may splash onto it. Be careful of equipment which drains water such as an air-conditioner.
  8. Ventilation — The vents and other openings in the cabinet are designed for ventilation.
    Do not cover or block these vents and openings since insufficient ventilation can cause overheating and/or shorten the life of the product. Do not place the product on a sofa, rug, or another similar surface, since they can block ventilation openings.
    Do not place the product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the manufacturer’s instructions are followed.
  9. Power cord protection — The power cords must be routed properly to prevent people from stepping on them or objects from resting on them.
  10. The screen used in this product is made of glass. Therefore, it can break when the product is dropped or applied with impact. Be careful not to be injured by broken glass pieces in case the screen breaks.
  11. Overloading — Do not overload power outlets or extension cords. Overloading can cause fire or electric shock.
  12. Entering of objects and liquids — Never insert an object into the product through vents or openings. High voltage flows in the product, and inserting an object can cause electric shock and/or short internal parts.
    For the same reason, do not spill water or liquid on the product.
  13. Servicing — Do not attempt to service the product yourself. Removing covers can expose you to high voltage and other dangerous conditions. Request a qualified service person to perform servicing.
  14. Repair — If any of the following conditions occurs, unplug the power cord from the power outlet, and request a qualified service person to perform repairs.
    a. When the power cord or plug is damaged.
    b. When a liquid was spilled on the product or when objects have fallen into the product.
    c. When the product has been exposed to rain or water.
    d. When the product does not operate properly as described in the operating instructions.
    Do not touch the controls other than those described in the operating instructions. Improper adjustment of controls not described in the instructions can cause damage, which often requires extensive adjustment work by a qualified technician.
    e. When the product has been dropped or damaged.
    f. When the product displays an abnormal condition. Any noticeable abnormality in the product indicates that the product needs servicing.
  15. Replacement parts — In case the product needs replacement parts, make sure that the service person uses replacement parts specified by the manufacturer or those with the same characteristics and performance as the original parts. The use of unauthorized parts can result in fire, electric shock, and/or other danger.
  16. Safety checks — Upon completion of service or repair work, request the service technician to perform safety checks to ensure that the product is in proper operating condition.
  17. Wall mounting — When mounting the product on a wall, be sure to install the product according to the method recommended by the manufacturer.
  18. Heat sources — Keep the product away from heat sources such as radiators, heaters, stoves, and other heat-generating products (including amplifiers).
  19. Usage of the monitor must not be accompanied by fatal risks or dangers that, could lead directly to death, personal injury, severe physical damage, or other loss, including nuclear reaction control in nuclear facilities, medical life support systems, and missile launch control in a weapon system.
  20. Do not stay in contact with the parts of the product that become hot for long periods of time. Doing so may result in low-temperature burns.
  21. Do not modify this product.

WARNING:
An apparatus with CLASS I construction shall be connected to the MAIN socket outlet with a protective earthing connection.
STABILITY HAZARD
If a monitor is not positioned in a sufficiently stable location, it can be potentially hazardous due to falling. Many injuries, particularly to children, can be avoided by taking simple precautions such as:

  • Using fixing devices like wall mount brackets recommended by the manufacturer.
  • Only using furniture that can safely support the monitor.
  • Ensuring the monitor is not overhanging the edge of the supporting furniture.
  • Not placing the monitor on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and the monitor to a suitable support.
  • Not standing the monitors on cloth or other materials placed between the monitor and supporting furniture.
  • Educating children about the dangers of climbing on furniture to reach the monitor or its controls.
  •  This equipment is not suitable for use in locations where children are likely to be present unsupervised.

Especially for child safety
– Don’t allow children to climb on or play with the monitor.
– Don’t place the monitor on furniture that can easily be used as steps, such as a chest of drawers.
– Remember that children can become excited while watching a program, especially on a “larger than life” monitor. Care should be taken to place or install the monitor where it cannot be pushed, pulled over, or knocked down.
– Care should be taken to route all cords and cables connected to the monitor so that they cannot be pulled or grabbed by curious children.

SAFETY INSTRUCTION

– Do not use the monitor where there is a lot of dust, where humidity is high, or where the monitor may come into contact with oil or steam. Do not use it in an environment where there are corrosive gases (sulfur dioxide, hydrogen sulfide, nitrogen dioxide, chlorine, ammonia, ozone, etc.). As this could lead to a fire.
– Ensure that the monitor does not come into contact with water or other fluids. Ensure that no objects such as paper clips or pins enter the monitor as this could lead to fire or
electric shock.
– Do not place the monitor on top of unstable objects or in unsafe places. Do not allow the monitor to receive strong shocks or to strongly vibrate. Causing the monitor to fall or topple over may damage it.
– Do not use the monitor near heating equipment or in places where there is the likelihood of high temperature, as this may lead to the generation of excessive heat and an outbreak of fire.
– Do not use the monitor in places where it may be exposed to direct sunlight. Risk of cabinet deformation and failure if the monitor is used in direct sunlight.
– Please be sure to constantly remove dust and garbage that has attached to the ventilation opening. If dust collects in the ventilation opening or the inside of the monitor, it may lead to excessive heat, an outbreak of fire, or malfunction.
Please request a cleaning of the inside of the monitor from an authorized SHARP servicing dealer or service center.
– The power outlet shall be installed near the equipment and shall be easily accessible.

The Power Cord
– Use only the power cord supplied with the monitor.
– Do not damage the power cord nor place heavy objects on it, stretch it, or over bend it. Also, do not add extension cords.
Damage to the cord may result in fire or electric shock.
– Do not use the power cord with a power tap.
Adding an extension cord may lead to fire as a result of overheating.
– Do not remove or insert the power plug with wet hands.
Doing so could result in electric shock.
– Unplug the power cord if it is not used for a long time.
– Do not attempt to repair the power cord if it is broken or malfunctioning. Refer the servicing to the service representative.

MOUNTING PRECAUTIONS

  • This product is for use indoors.
  • When moving the monitor, be sure to hold its sides or bottom. Do not hold the LCD panel or buttons. This may cause product damage, failure, or injury. This may cause
    product damage, failure, or injury.
  • Use the monitor with the surface perpendicular to a level surface.
  • This monitor should be used at an ambient temperature between 41°F (5°C) and 95°F (35°C).
    Provide enough space around the monitor to prevent heat from accumulating inside.

For the monitor in landscape orientation

For the monitor in portrait orientation

  • Temperature conditions may change when using the monitor together with the optional equipment recommended by SHARP. In such cases, please check the temperature
    the condition specified by the optional equipment.
  • Do not block any ventilation openings. If the temperature inside the monitor rises, this could lead to a malfunction.
  • Do not place the monitor on a device that generates heat.
  • To install the monitor in portrait orientation, a mounting bracket compliant with VESA specifications is required.
    A stand supplied with this product cannot be used for installation in portrait orientation.
  • Adhere to the following when installing the monitor in its portrait orientation. Failing to adhere to the following may cause malfunctions.
    – Install the monitor such that the power LED is located on the bottom side.
    – Set the PORTRAIT/LANDSCAPE INSTALL in the MONITOR menu to PORTRAIT. (See OPERATION MANUAL.)
    – Be sure to clamp the power cord (supplied) onto the cable clamp attachment using the supplied cable clamp. When clamping the power cord, take care not to stress the terminal of the power cord. Do not bend the power cord excessively.

  • Do not press the monitor surface. Doing so may cause display unevenness.
  • After mounting, please carefully ensure the monitor is secure, and not able to come loose from the wall or mount.
  • To attach a VESA-compliant mounting bracket, use M6 screws that are 5/16 inch (8 mm) to 3/8 inch (10 mm) longer than the thickness of the mounting bracket.

  • Be sure to use a wall-mount bracket designed or designated for mounting the monitor.
  • This monitor and bracket must be installed on a wall that can endure at least 4 times or more the weight of the monitor. Install by the most suitable method for the material
    and the structure.
  • Do not use an impact driver.
  • Do not use any screw holes other than those for mounting brackets, located on the rear of the monitor, for installation.

Removing the stand
Caution

  • If there are cables already connected, disconnect them all.
  1. Spread a thick, soft cloth (blanket, etc.) that will prevent damage to the LCD panel on a stable flat surface where the entire monitor can be placed, and place the monitor with the LCD panel face down on the cloth.
  2. Remove the screws(x2) that fasten the stand.
    Keep the removed screws in a safe place.
  3. Pull out the stand from the monitor.
  4. Install the provided stand mounting part covers to the holes where the stand was attached to.
    Install the covers so that their tabs are on the right side.

Installing the stand
Assemble in the opposite order of the removal.

Specifications

Model 8M-B32C1
Power requirement AC 100 V – 240 V, 2.9 A, 50/60 Hz
Operating temperature * 41°F to 95°F (5°C to 35°C)
Operating humidity 20% to 80% (no condensation)
Power consumption (Maximum) 260 W
Dimensions (excluding protrusions) inch (mm) With the stand
Approx. 29-9/16 (W) x 10-1/4 (D) x 21-1/4 (H) (751 x 260 x 540)
Without the stand
Approx. 29-9/16 (W) x 3-7/8 (D) x 18-7/16 (H) (751 x 99 x 469)
Weight lbs. (kg) Approx. 29.4 (13.3) (monitor only)
Approx. 42.4 (19.2) (with the stand attached)

* Temperature conditions may change when using the monitor together with the optional equipment recommended by SHARP. In such cases, please check the temperature condition specified by the optional equipment.
As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.

Supplied Components

If any components are missing, please contact your dealer.

  • Liquid Crystal Display Monitor: 1
  • Cable clamp: 5
  • Power cord
  • Stand mounting part cover: 2
  • CD-ROM: 1
  • Setup Manual (this manual): 1

* SHARP Corporation holds authorship rights to the Utility Disk program. Do not reproduce it without permission.

Connections

  1. HDMI1 input terminal (8K)
  2. HDMI2 input terminal (8K, HDMI x 4)*
  3. HDMI3 input terminal (4K)
  4. DisplayPort input terminal (4K)
  5. Audio output terminal
  6. USB Type B port (USB2.0)
  7. AC input terminal
  8. Terminal for firmware update (Normally not used.)

* Connect so that output signals from the 8K-output-compliant device are displayed in the appropriate positions.

Select an audio input in HDMI2 AUDIO SELECT of the SETUP menu. (HDMI2- is selected by factory default.)

Caution

  • Be sure to turn off the main power switch and disconnect the plug from the power outlet before connecting/disconnecting cables. Also, read the manual of the equipment to be connected.
  • Do not use any cable that has a damaged or deformed terminal. Using such cables may cause malfunctions.
  • Do not forcibly bend or apply force to cables. Doing so may result in wire breakage or other damage.

TIPS

  • Images may not be displayed properly depending on the computer (video card) to be connected.
  • If the audio output from the playback device is connected directly to speakers or other devices, the video on the monitor may appear delayed from the audio portion.
    Audio should be played through this monitor by connecting the playback device to the monitor, and connecting the monitor’s audio output to the speakers or other devices.
  • Install SHARP Information Display Downloader.
  • Download SHARP Display Calibration Utility from SHARP Information Display Downloader.
  • When using SHARP Display Calibration Utility, connect the monitor to the computer in which SHARP Display Calibration Utility uses a commercially available USB cable.
  •  When the Information Display Downloader is installed, you can check and download the most recent versions of the software programs.
  • For detailed information on SHARP Information Display Downloader, refer to its operation manual.
    * You must be in a network environment that allows access to the Internet.
  • The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
  • DisplayPort is a registered trademark of the Video Electronics Standards Association.
  • VESA is either a registered trademark or trademark of the Video Electronics Standards Association in the United States and/ or other countries.
  • All other brand and product names are trademarks or registered trademarks of their respective holders.

Turning Power On/Off

Caution

  • Turn on the monitor first before turning on the computer or playback device.
  • When switching the main power switch or the POWER button off and back on, always wait for at least 5 seconds.
    A short interval may result in a malfunction.

Turning on the main power

Off mode, when main power is off.

Caution

  • The main power must be turned on/off with the main power switch. Do not connect/disconnect the power cord or turn the breaker on/off while the main power switch is on.
  • For a complete electrical disconnection, pull out the main plug.

Turning power on/off
Press the POWER button to turn the power ON/OFF.
Wait for 15 minutes or more before use to stabilize the image quality.

Status Status of the monitor
Greenlit Power on
Not lit Power off (Standby state*)
Orange lit Input signal waiting for state

* Standby mode

Operations after first power-on
Date/time setting

  • If the time has yet to be set, the date/time setting screen appears. Set the date and time.

  1. Press the button to select the date and time, and press the button to change the numerical values.
  2. Press the ENTER button.
  • Be sure to set the date and time.
  • The date/time setting screen will close automatically if no operation is performed for about 15 seconds. The date and time can be set using DATE/TIME SETTING
    from the SETUP menu when the date/time setting screen disappears.

TIPS

  • Set the date in “Day/Month/Year” order.
  • Set the time on a 24-hour basis.
  • The clock is maintained by the internal battery.
  • If you already set the time but the date/time setting screen appears when the power is turned on, the internal battery may be exhausted. Please contact an authorized SHARP servicing dealer or service center for assistance with battery replacement.
  • The estimated service life of the internal battery: About 5 years (depending on monitor operation)
  • The initial battery was inserted at the factory when the monitor was shipped, so it may run out of power before its expected operation life.

SHARP CORPORATION
FOR CUSTOMERS IN THE U.K.
IMPORTANT

The wires in this mains lead are colored in accordance with the following code:
GREEN-AND-YELLOW: Earth
BLUE: Neutral
BROWN: Live

As the colors of the wires in the mains lead of this apparatus may not correspond with the colored markings identifying the terminals in your plug proceed as follows:

  • The wire which is colored GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safety earth or colored green or green-and-yellow.
  • The wire which is colored BLUE must be connected to the terminal which is marked with the letter N or colored black.
  • The wire which is colored BROWN must be connected to the terminal which is marked with the letter L or colored red.

Ensure that your equipment is connected correctly. If you are in any doubt consult a qualified electrician.
“WARNING: THIS APPARATUS MUST BE EARTHED.”

The product Energy Label and Product Information Sheet can be found on the online European database known as EPREL (European Product Registry for Energy Labelling).

https://eprel.ec.europa.eu/qr/553204