Philips ADD4901 Gozero Black Sparkling Water Maker User Manual

Philips ADD4901 Gozero Black Sparkling Water Maker

Name of the parts

  1. Button
  2. Decorative cover
  3. Gas cylinder compartment
  4. Bottom cap
  5. Pedestal
  6. Drip tray
  7. Carbonating bottle
  8. Upper cover

Introduction

Congratulations on your purchase and welcome to Philips! To fully benefit from the support that we offer, register your product at www.philips.com/water.

For your safety

Read this important information carefully before you use the appliance and save it for future reference.
General Warning

  • DO NOT use carbonating bottles from other brands. This can damage the machine and lead to safety risk.
  • DO NOT carbonate anything other than plain water. If the water contains sugar or other compounds the valves could malfunction and it could be dangerous to use the product.
  • DO NOT add fruit slices, ice and flavour in the carbonating bottle. Add flavour only AFTER carbonation.
  • DO NOT carbonate into an empty carbonating bottle.
  •  DO NOT move the Sparkling water maker when it is carbonating.
  •  DO NOT carbonate for over 5 seconds.
  • Always use your Sparkling water maker in an upright position.
  • Always keep the Sparkling water maker away from any source of heat or direct sunlight. Use it in the room temperature.
  • Keep the Sparkling water maker away from children. It is not recommended to be used by children under 12 years old without adult supervision.

Carbonating bottle

  • Fill the bottle with clean and cold water only up to the fill line.
  • NEVER wash the plastic bottle in dishwashers. DO NOT wash it in hot water exceeding 40℃.
  • DO NOT use other bottles not specifically designed for Philips Sparkling water maker. Your Philips Sparkling water maker is designed to use only with the Philips carbonating bottle. The use of other bottles is not recommended. Damages resulting from the use of a bottle other than a Philips carbonating bottle are not covered by the warranty.
  • Philips bottles are clearly marked with an expiration date. Do not use the carbonating bottle after the expiry date.
  • Never use a bottle that has been deformed, discolored or scratched. Before each use, check the expiration date on the bottle, and check for damage and deformation. Replace expired, damaged or deformed carbonating bottles with new ones.
  • Never put the bottle in the freezer.
  •  Always keep the bottle clean with the cap on to avoid bacteria and bad smell.

General description

Product overview

Machine rating of information:

  • Maximum Working Pressure: 116 psi/ 8 bar
  • Maximum Allowed Operating Temperature: 40°C / 104°F

Before creating fun

Installing the gas cylinder

  1. Place the Philips Sparkling water maker in an upright position and on a flat surface. Remove the carbonating bottle before installing or replacing the cylinder if it is filled with water. Remove the drip tray grid and then carefully lay the Sparkling water maker down on the side.
  2. Remove seal and cap from the CO2 cylinder. Carefully insert the cylinder through the hole at the bottom. Don’t drop the cylinder into the hole. When you feel that it reaches the bottom, begin screwing the cylinder clockwise until it is fastened. Don’t screw too hard since this might break the threads holding the gas cylinder in place. A2-1
  3. When you need to replace the gas cylinder, lay the Sparkling water maker down on the side and unscrew it counterclockwise and then carefully pull it out of the compartment. A2-2

Let the fun begin

  1. Fill the carbonating bottle: Rinse the carbonating bottle with cold water before you use it for the first time. Fill the carbonating bottle with cold, clean water up to the marked filling line. A3-1
  2. Attach the carbonating bottle: Screw the carbonating bottle into the carbonating bottle socket. Screw counterclockwise if viewed from above. Don’t screw extremely hard – just make sure the carbonating bottle sits properly. A3-2
  3. Carbonate the water: Press the button downwards firmly until you hear a sound from the valve. The carbonation time is 2-3 seconds for each time.

NOTE: 

  • NEVER continuously carbonate for over 5 seconds each time. It can lead to gas wastes or personal injury.
  • You can add more carbonation to the water by repeating the carbonating process.

Ventilate the bottle

When hearing a buzzing sound after 3 seconds, you should release the button back to horizontal position. Please allow the button release itself. The remaining pressure in the carbonating bottle will be released with a puff sound. Then the sparkling water is ready. You can unscrew the carbonating bottle and enjoy it now. A3-4

Cleaning

Rinse the carbonating bottle 

  • Rinse the carbonating bottle before the first use.
  • Use clean cold water, fiber brush with a mild detergent.
  • Do not use solvent, strong detergent cleaner or abrasive cleaners to clean.

NOTE:

  • Never wash the Philips carbonating bottles in a dishwasher.

Clean the Sparkling water maker

  •  DO NOT use abrasive cleaners or solvent cleansers to clean.
  • Wipe the drip tray to keep it dry.

Guarantee & service

If you need information or if you have any problems, please visit the Philips website at www.philips.com or contact the Philips Customer Care Center in your country. If there is no Customer Care Center in your country, go to local Philips dealer.