Makita ML187 Rechargeable Flash Light Instruction Manual

makita ML187 Rechargeable Flash Light

Explanation of general view

  1. Battery cartridge
  2. Red indicator
  3. Button
  4. Switch
  5. Shoulder strap

SPECIFICATIONS

Model ML187
LED 0.1 W x 9 pcs
Standard battery cartridges BL1415G BL1420G BL1815G BL1820G
Voltage 14.4 V 18 V
Operating time (Approx.) 20 hours 25 hours 22 hours 27 hours
Dimensions (L x W x H) (with battery) 313 mm × 84 mm × 101 mm 313 mm × 84 mm × 118 mm
Net weight (with battery) 0.66 kg 0.67 kg 0.72 kg 0.73 kg
  • Due to our continuing program of research and development, the specifications herein are subject to change without
  • Specifications may differ from country to
  • Weight, with battery cartridge, according to EPTA-Procedure 01/2014.

Symbols

  • Read instruction manual.
  • Indoor use only
  • Only for EU countries

Due to the presence of hazardous components in the equipment, waste electrical and electronic equipment, accumulators and batteries may have a negative impact on the environment and human health. Do not dispose of electrical and electronic appliances or batteries with household waste! In accordance with the European Directive on waste electrical and electronic equipment and on accumulators and batteries and waste accumulators and batteries, as well as their adaptation to national law, waste electrical equipment, batteries and accumulators should be stored separately and delivered to a separate collection point for municipal waste, operating in accordance with the regulations on environmental protection. This is indicated by the symbol of the crossed- out wheeled bin placed on the equipment.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury, including the following:

READ ALL INSTRUCTIONS
  1. Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery.
  2. Recharge only with the charger specified by the A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
  3. Use a power source with the voltage specified on the nameplate of the charger.
  4. Do not attempt to use a step-up transformer, an engine generator or DC power receptacle.
  5. Charge the battery cartridge with room temperature at 10°C – 40°C (50°F – 104°F). Let a hot battery cartridge cool down before charging it.
  6. When battery pack is not in use, keep it away from other metal objects like paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause sparks, burns, or a fire.
  7. After charging or before attempting any maintenance or cleaning, unplug the charger from the power
  8. This battery holder part is not Do not use it in damp or wet locations. Do not expose it to rain or snow. Do not wash it in water.
  9. Do not touch the inside of the flashlight head with tweezers, metal tools, etc.
  10. Under abusive conditions, liquid may be ejected from the battery, avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical Liquid ejected from the battery may cause irritation or burns.
  11. Do not short the battery cartridge:
    • Do not touch the terminals with any conductive
    • Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc.
    • Do not expose battery cartridge to water or
    • A battery short can cause a large current flow, overheating, possible burns and even a breakdown.
  1. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right It may result in loss of your eyesight.
  2. Be careful not to drop or strike
  3. Do not incinerate the battery cartridge even if it is severely damaged or is completely worn The battery cartridge can explode in a fire.

CAUTION:

  1. When the tool is not in use, always switch off and remove the battery cartridge from the tool.
  2. Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50°C (122°F).
  3. Do not give the tool a shock by dropping, striking,
  4. Do not expose the light to eyes It may hurt them.
  5. Do not cover or clog the lit tool with cloth or carton, Covering or clogging it may cause a flame.
  6. Do not disassemble the charger or battery cartridge; take it to a qualified serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire.
  7. Use the tools only with specifically designated battery Use of any other battery packs may create a risk of injury and fire.
  8. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion.
  9. Do not use a damaged
  10. Charge the battery cartridge before completely Always stop tool operation and charge the battery cartridge when you notice less tool power.
  11. Never recharge a fully charged battery Overcharging shortens the battery service life.
  12. If any problem develops, consult your nearest Makita Service Center or To maintain product safety and reliability, repairs, maintenance or adjustment should be carried out by Makita Authorized Service Center.

SAVE THESE INSTRUCTIONS.

FUNCTIONAL DESCRIPTION

Charging

Charge the battery cartridge with the Makita charger before use.

Installing or removing battery cartridge (Fig. 1)

  • Always switch off the tool before installing or removing of the battery cartridge.
  • To remove the battery cartridge, slide it from the tool while sliding the button on the front of the cartridge.
  • To install the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Always insert it all the way until it locks in place with a little click. If you can see the red indicator on the upper side of the button, it is not locked Install it fully until the red indicator cannot be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you.
  • Do not use force when installing the battery If the cartridge does not slide in easily, it is not being inserted correctly.

Lighting up the LED light (Fig. 2)

  • Do not look in the LED light or see the source of light
  • This tool has function that the LED light goes out at low At this time, recharge the battery cartridge. Push the switch to light up the LED light. To turn off, push the switch again.

Battery Protection System

The protection system is equipped, which automatically cuts off the output power for its long service life. The light goes off during operation when the remaining battery capacity gets low. This is caused by the activation of protection system and does not show the light trouble. Remove the battery cartridge from the light and charge it.

Head Angle (Fig. 3)

The head angle can be adjusted in four stages. Adjust as desired.

Shoulder Strap (Fig. 4)

Install the strap on the tool.

MAINTENANCE

CAUTION

  • Never use gasoline, benzine, thinner, alcohol or the Discoloration, deformation or cracks may result.
  • To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized Service Centers, always using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner.

  • Shoulder strap
  • Makita genuine battery and charger

NOTE: Some items in the list may be included in the tool package as standard accessories. They may differ from country to country.