HP HSD-0087-Q LCD Monitor User Guide
CP_Reg_Display_Product_Notices_837061-B29.fm Page 2 Friday, June 28, 2019 1:09 PM
Regulatory notices
This document provides country- and region-specific non-wireless and wireless regulatory notices and compliance information for your product.
Some of these notices may not apply to your product.
Federal Communications Commission notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio or television technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
For questions regarding the product, contact:
HP Inc.
1501 Page Mill Road
Palo Alto, CA 94304
Or, call HP at 650-857-1501.
To identify your product, refer to the part, series, or model number found on the product.
Modifications
The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by HP may void the user’s authority to operate the equipment.
Cables
Connections to this device must be made with shielded cables having metallic RFI/EMI connector hoods to maintain compliance with FCC Rules and Regulations.
Products with wireless LAN devices or HP Mobile Broadband Modules
This device must not be co-located or operating in conjunction with any other antenna or transmitter.
To avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antennas should not be less than 20 cm (8 inches). To identify the location of the wireless antennas, refer to the computer user guides included with your computer.
Canada notices
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations CAN ICES-3(B)/NMB-3(B). If this device has WLAN or Bluetooth® capability, the device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
To avoid the possibility of exceeding the Industry Canada radio frequency exposure limits, human proximity to the antennas should not be less than 20 cm (8 inches), including when the computer display is closed. To identify the location of the wireless antennas, refer to the computer user guides included with your computer.
The antennas for this device are not replaceable. Any attempt at user access will damage your computer.
Radiation Exposure Statement:
This product complies with the US/Canada portable RF exposure limit set forth for an uncontrolled environment and is safe for intended operation as described in this manual. Further RF exposure reduction can be achieved if the product can be kept as far as possible from the user’s body or set the device to lower output power if such function is available.
European Union regulatory notices
Declaration of Conformity
Products bearing the CE marking have been constructed so that they can operate in at least one EU Member State and comply with one or more of the following EU Directives as may be applicable:
RED 2014/53/EU; Low Voltage Directive 2014/35/EU; EMC Directive 2014/30/EU; Ecodesign Directive 2009/125/EC; RoHS Directive 2011/65/EU.
Compliance with these directives is assessed using applicable European Harmonised Standards.
The full Declaration of Conformity can be found at the following website: http://www.hp.eu/certificates (Search with the product model name or its Regulatory Model Number (RMN), which may be found on the regulatory label.)
The point of contact for regulatory matters is HP Deutschland GmbH, HQ-TRE,71025, Boeblingen, Germany. Email .
Products with radio functionality (EMF)
This product incorporates a radio transmitting and receiving device. For notebook computers in normal use, a separation distance of 20 cm ensures that radio frequency exposure levels comply with EU requirements. Products designed to be operated at closer proximities, such as tablet computers, comply with applicable EU requirements. Products can be operated without maintaining a separation distance unless otherwise indicated in instructions specific to the product.
Restrictions for products with radio functionality
This product is designed for use without restrictions in all EU countries, plus Iceland, Liechtenstein, Norway, and Switzerland.
German ergonomics notice
A computer system comprising HP brand products meets the applicable German ergonomic requirements if all affected constituent products bear the “GS” approval mark, for example, Business Desktop PC, keyboard, PC-mouse, and monitor.
Australia and New Zealand notice
This equipment incorporates a radio transmitting and receiving device. In normal use, a separation distance of 20 cm ensures that radio frequency exposure levels comply with the Australian and New Zealand Standards.
Singapore wireless notice
Turn off any WWAN devices while you are on board the aircraft. The use of these devices on board aircraft is illegal and may be dangerous to the operation of the aircraft and may disrupt the cellular network. Failure to observe this instruction may lead to suspension or denial of cellular services to the offender, legal action, or both.
Users are reminded to restrict the use of radio equipment in fuel depots, chemical plants, and where blasting operations are in progress.
As with other mobile radio transmitting equipment, users are advised that for satisfactory operation of the equipment and for the safety of personnel, no part of the human body should be allowed to come too close to the antennas during the operation of the equipment.
This device has been designed to comply with applicable requirements for exposure to radio waves, based on scientific guidelines that include margins intended to assure the safety of all people, regardless of health and age. These radio wave exposure guidelines employ a unit of measurement known as the specific absorption rate (SAR). Tests for SAR are conducted using standardized methods, with the phone transmitting at its highest certified power level in all used frequency bands. The SAR data information is based on CENELEC’s standards EN50360 and EN50361, which use the limit of 2 watts per kilogram, averaging over 10 grams of tissue.
Thailand WWAN wireless notice
This telecom equipment has complied with NTC regulations.
Power cord notice
The monitor power supply is provided with Automatic Line Switching (ALS). This feature allows the monitor to operate on input voltages between 100–120V or 200–240V.
The power cord set (flexible cord or wall plug) received with the monitor meets the requirements for use in the country where you purchased the equipment.
A power cord should be routed so that it is not likely to be walked on or pinched by items placed upon it or against it. Particular attention should be paid to the plug, electrical outlet, and the point where the cord exits from the product.
Japanese power cord requirements
For use in Japan, use only the power cord received with this product.
Safety notices
Health and Safety Warning Notice for OMEN X 65 and OMEN X 65 SB Displays
Carefully read all of the following safety precautions before using the OMEN X 65 and OMEN X 65 SB Displays (“Display(s)”).
If you experience any of the following symptoms, immediately stop using Display(s) functionality and consult a physician: altered vision, light-headedness, dizziness, involuntary movements such as eye or muscle twitching, convulsions, nausea, loss of awareness, confusion, cramps, and/or disorientation.
RESUME DISPLAY(S) USAGE ONLY ON APPROVAL OF YOUR PHYSICIAN.
Parents should monitor and ask their children if they have any of the above symptoms. Children and teenagers may be more likely than adults to experience these symptoms.
The vision of young children (especially children under the age of 6) is still under development. Consult your physician (such as a pediatrician or eye doctor) before allowing young children to use Display(s) functionality.
Use and handling of Display(s) to help reduce the likelihood of adverse physical reactions:
- Use in a well-lit area and moderate the brightness of the Display(s).
- Keep as far away as possible from Display(s) when using functionality.
- Avoid prolonged use of Display(s).
- Take a 15-minute break during each hour of Display(s) use. The length and frequency of necessary breaks may vary from person to person.
Please take breaks that are long enough to allow any feelings of discomfort to subside. If symptoms persist, consult a physician. - Avoid using Display(s) functionality when you are tired or need sleep.
When a battery has reached the end of its useful life, do not dispose of the battery in general in household waste. Follow the local laws and regulations in your area for battery disposal.
HP encourages customers to recycle used electronic hardware, HP original print cartridges packaging, and rechargeable batteries. For more information about recycling programs refer to the HP Web site at http://www.hp.com/recycle.
For information about removing a user-replaceable battery, refer to the user guide included with the product.
Potential safety conditions notice
If you notice any of the following conditions (or if you have other safety concerns), do not use the monitor: crackling, hissing, or popping sound, or a strong odor or smoke coming from the monitor. It is normal for these conditions to appear when an internal electronic component fails in a safe and controlled manner. However, these conditions may also indicate a potential safety issue. Do not assume it is a safe failure. Turn off the monitor, disconnect it from its power source, and contact technical support for assistance.
China safety notices
China: Altitude notice
Altitude warning for products not certified for use in >5000 m.
China: Tropical warning notice
Tropical warning for products not certified for use in tropical regions.
Product environmental notices
This document provides country- and region-specific environmental notices and compliance information. Some of these notices may not apply to your product.
Electronic hardware, packaging, and battery recycling
HP encourages customers to recycle used electronic hardware, HP original print cartridges, and rechargeable batteries. For more information about recycling programs, go to http://www.hp.com/recycle.
For information about recycling the product in Japan, refer to http://www.hp.com/jp/hardwarerecycle/.
Disposal of waste equipment by users
This symbol means do not dispose of your product with your other household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment.
For more information, please contact your household waste disposal service or go to http://www.hp.com/recycle.
Taiwan EPA battery information
ENERGY STAR® qualification
✎
This section applies only to products bearing the ENERGY STAR logo.
As an ENERGY STAR Partner, HP Inc. has followed the U.S. Environmental Protection Agency (EPA) enhanced product qualification and certification process to ensure that the products marked with the ENERGY STAR logo are ENERGY STAR-qualified per the applicable ENERGY STAR guidelines for energy efficiency.
The following logo appears on all ENERGY STAR-qualified displays:
The ENERGY STAR
program specifications for displays and computers were created by the EPA to promote energy efficiency and reduce air pollution through more energy-efficient equipment in homes, offices, and factories. One way products achieve this goal is by using the Microsoft ®Windows ® power management feature to reduce power consumption when the product is not in use.
The power management feature enables the computer to initiate a low-power or “sleep” mode after a period of user inactivity. When used with an external ENERGY STAR qualified display, this feature also supports similar power management features for the display. To take advantage of these potential energy savings, users should use the default power management settings that are provided with ENERGY STAR qualified computers and displays. The default power management settings on ENERGY STAR-qualified computers are preset to behave in the following ways when the system is operating on AC power:
- Turn off an external display after 5 minutes of user inactivity
- Initiate a low-power sleep mode for the computer after 30 minutes of user inactivity
ENERGY STAR-qualified computers exit the low-power sleep mode and ENERGY STAR-qualified displays resume operation when the user resumes use of the computer. Examples include the user pressing the power/sleep button, receiving an input signal from an input device, receiving an input signal from a network connection with the Wake On LAN (WOL) feature enabled, etc.
Changes to the default as-shipped settings may increase the energy consumption beyond the Energy Star certification limits. For select display products, you can change from the default power setting to the Performance power setting that enables additional display features and functions.
The Performance setting can increase power consumption.
Additional information on the ENERGY STAR program, its environmental benefits, and the potential energy and financial savings of the power management feature can be found on the EPA ENERGY STAR
Power Management website at http://www.energystar.gov/powermanagement.
Chemical substances
HP is committed to providing our customers with information about the chemical substances in our products as needed to comply with legal requirements such as REACH (Regulation EC No1907/2006 of the European Parliament and the Council). A chemical information report for this product can be found at http://www.hp.com/go/reach.
Mercury statement
This statement applies to computer displays that do not use LED backlighting.
This HP product may contain the following material that might require special handling at end-of-life:
- Mercury in the fluorescent lamp in the display LCD
The disposal of mercury can be regulated because of environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance (EIA) (http://www.eiae.org)\
Perchlorate Material–special handling may apply
The computer’s real-time clock battery may contain perchlorate and may require special handling when recycled or disposed of in California. See http://www.dtsc.ca.gov/hazardouswaste/perchlorate/.
The Display CEL user information
In accordance with “The Regulation of the Implementation on China Energy Label for PC Monitors”(CEL rule), this monitor has an Energy Efficiency Label. The energy efficiency grade, energy efficiency, off-mode power consumption, sleep-mode power consumption, and product category presented on the label are determined and calculated according to the standard Minimum Allowable Values of Energy Efficiency and Energy Efficiency Grades for Computer Monitors (GB21520).\
- Energy efficiency grades
The energy efficiency level is classified into three grades, where grade one is the most efficient. The grade is determined by the standard according to product category and the calculation of energy efficiency. - Product category
There are two types of categories: Standard display and enhanced performance display, and classification is based on display product functionalities on contrast ratio, native resolution, and NTSC color gamut. - Energy efficiency information
■ Energy efficiency measured and calculated as specified in GB21520. This data is expressed in (cd/watts (W)).
■ Off mode power consumption measured and calculated as specified in GB21520. This data is expressed in watts (W).
■ Sleep mode power consumption measured and calculated as specified in GB21520, this data is expressed in watts (W).
The energy consumption figure presented on the label is the data measured with the representative configuration that covers all the configurations in the registration unit, which is selected according to the CEL rule. Thus, the actual energy consumption of this specific monitor may not be the same as the data presented on the label.
For more details on the specification, please refer to the GB21520 standard.
Declaration of the Presence Condition of the Restricted Substances Marking
Restricted substances and its chemical symbols
| Unit | Lead
(Pb) |
Mercury
(Hg) |
Cadmium
(Cd) |
Hexavalent +6 chromium (Cr ) | Polybrominated
biphenyls (PBB) |
Polybrominated diphenyl ethers (PBDE) |
| Plastic Bezel | 0 | 0 | 0 | 0 | 0 | 0 |
| Rear Cover | 0 | 0 | 0 | 0 | 0 | 0 |
| Liquid Crystal Display (LCD) Panel | – | 0 | 0 | 0 | 0 | 0 |
| Printed Circuit Board Assembly (PCBA) | – | 0 | 0 | 0 | 0 | 0 |
| Power Cord | – | 0 | 0 | 0 | 0 | 0 |
| Cables | – | 0 | 0 | 0 | 0 | 0 |
Note 1: “Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicates that the percentage content of the restricted substance exceeds the reference percentage value of the present condition.
Note 2: “O” indicates that the percentage content of the restricted substance does not exceed the percentage of the reference value of presence.
Note 3: The “ － ” indicates that the restricted substance corresponds to the exemption.
To access the latest user guides or manuals for your product, go to http://www.support.hp.com. Select Find your product, and then follow the on-screen instructions.
India’s restriction of hazardous substances (RoHS)
This product, as well as its related consumables and spares, complies with the reduction in hazardous substances provisions of the “India E-waste Rule 2016.” It does not contain lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except where allowed pursuant to the exemptions set in Schedule 2 of the Rule.
Information for European Union Commission Regulation 1275/2008
To locate product power consumption data, including when the product is in networked standby with all wired network parts connected, refer to section P14 “Additional information” of the product IT ECO Declaration at
http://www.hp.com/hpinfo/globalcitizenshlp/environment/productdata/itecodesktop-pc.html.
Where applicable, activate and deactivate a wireless network using the instructions included in the product user guide or the operating system.
Information is also available at http://www.hp.com/support.
© Copyright 2015, 2016, 2018, 2019 HP Development Company, L.P.
ENERGY STAR is a registered mark owned by the U.S. government.
Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
Bluetooth is a trademark owned by its proprietor and used by HP Inc. under license.
The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
Ninth Edition: July 2019
First Edition: August 2015
Printed in China
