Craftsman CMXWDCR01137 Wireless Thermometer Instruction Manual

CRAFTSMAN CMXWDCR01137 Wireless Thermometer

Definitions: Safety Alert Symbols and Words
This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk f personal injury or property damage.

  • DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
  • WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
  • CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.(Used without word) Indicates a safety related message.
  • NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in property damage.

    Read all safety warnings and all instructions before operating devices.
    Compare the illustrations with the devices to familiarize yourself with the supplied components and setup instructions.
    SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE

WARNING: GENERAL SAFETY
  • Do not immerse device in water. This can cause electrical shock and damage the product.
  • Do not disassemble device or tamper with internal components. Damage caused by disassembly is not covered by the warranty. No user-serviceable parts are inside these devices.
  • Avoid dropping device; this may damage internal components.
  • Keep all parts and batteries out of the reach of children.
  • Use care when mounting the Wireless Outdoor Sensor out of arm’s reach. When using a ladder to mount, it must be secure to avoid falls that may result in personal injury or property damage.
  • Do not mount Wireless Outdoor Sensor near overhead power lines or other unsafe hanging areas.

WARNING: BATTERY SAFETY AND DISPOSAL BATTERY SAFETY

BATTERY SAFETY
Clean the battery contacts and also those of the device prior to battery installation. Remove batteries from device which is not to be used for an extended period of time. Replace all batteries of a set at the same time. Only batteries of the same or equivalent type as recommended are to be used. Ensure the batteries are installed with correct polarity (+ and -). Promptly remove dead or expired batteries.
CAUTION: DO NOT mix old and new batteries or batteries of different types. DO NOT use rechargeable batteries. DO NOT recharge non-rechargeable batteries. DO NOT short-circuit the supply terminals.

BATTERY DISPOSAL
Dispose of old or defective batteries in an environmentally safe way and in accordance with your local laws and regulations.
WARNING: DO NOT incinerate used batteries. DO NOT dispose of batteries in fire, because they could explode or leak.

WARNING: MAINTENANCE AND CARE
  • Clean devices with a soft, damp cloth. Do not use caustic cleaners or abrasives.
  • Keep Indoor Display away from dust, dirt, and moisture. Clean ventilation ports regularly with a gentle puff of air.
  • Replace device batteries when low battery icon is shown. Follow all battery recommendations, disposal, and safety information detailed in this guide.
  • Wireless Outdoor Sensor is water-resistant and designed for general outdoor use. To extend its life, place in an area protected from direct weather elements, including rain, snow, and frost.

KNOW YOUR WIRELESS THERMOMETER

Weather the day with confidence with your own accurate and up-to-date information – right from your own backyard. The CRAFTSMAN Wireless Thermometer features precise, reliable temperature and humidity readings, along with the time and date. The bold, easy to read LCD screen displays the current indoor / outdoor temperature and humidity with trend indicator arrows and daily high / low information. The Indoor Display stands upright for tabletop use or is wall-mountable. The Wireless Outdoor Sensor features powerful wireless technology, a weather-resistant design and an integrated hanger for easy mounting.

INDOOR DISPLAY FEATURES
  1. Outdoor Conditions
    • Current temperature (°F or °C)
    • Current humidity level (%)
    • Trending arrows indicate if the condition is trending up or down
    • Wireless Outdoor Sensor signal strength
    • Wireless Outdoor Sensor low battery icon indicates when batteries need to be changed
  2. Indoor Display Information
    • Current time and date
    • Low battery indicator indicates when batteries need to be changed
  3. Indoor Conditions
    • Current temperature (°F or °C)
    • Current humidity level (%)
    • Trending arrows indicate if the condition is trending up or down
  4. Display Buttons
    • MIN/MAX buttons: view today’s low and high temperature and humidity records
    • SETUP and buttons: set time, date, and temperature units to Fahrenheit or Celsius
  5. Battery compartment
    Requires three AAA batteries (not included)
  6. Tabletop stand

WIRELESS OUTDOOR SENSOR FEATURES

  1. Mounting Hanger
  2. Wireless Signal Indicator
    Flashes when sending data to the Indoor Display
  3. Battery Compartment
    Requires two AA batteries (not included)

HOW TO SET UP YOUR WIRELESS THERMOMETER

What You’ll Need (Not Included)

  • Two AA batteries for the Wireless Outdoor Sensor
    Be sure to use high-quality alkaline batteries. Heavy duty or rechargeable batteries are not recommended. Only use Lithium batteries when the outdoor temperature is below -4ºF/-20ºC for extended periods of time. In general, alkaline batteries perform poorly in very cold weather.
  • Three AAA batteries for the Indoor Display
    Be sure to use high-quality alkaline batteries. Lithium, heavy duty, and rechargeable batteries are not recommended.
  • STEP 1
    Insert Wireless Outdoor Sensor Batteries
  • STEP 2
    Insert Indoor Display Batteries

  • STEP 3
    Set Indoor Display Time, Date, and Temperature Units to Fahrenheit or Celsius
    • Press and hold the SETUP button. When in setup mode, the selected setting flashes on the Indoor Display.
    • To adjust a setting, press and release the or button. To save a setting, press and release the SETUP button. The next setting is selected.
    • Settings are displayed in the following order:
    • Auto DST ON/OFF. When set to ON, time will update for Daylight Saving Time.
      If your location does not observe DST, set it to OFF.
    • CLOCK HOUR
    • CLOCK MINUTE
    • CALENDAR MONTH
    • CALENDAR DATE
    • CALENDAR YEAR
    • TEMPERATURE UNITS (ºF or ºC)
    • To exit from setting mode, do not press a button for 8 seconds. The Indoor Display returns to its normal operating mode.
  • STEP 4
    • Place Indoor Display And Wireless Outdoor Sensor
      Both devices are sensitive to their surrounding environment and location. Proper placement is required for accurate readings and wireless communication.
    • Important Location Guidelines For Wireless Communication
      The following guidelines are very important to ensure both devices have signal strength to connect wirelessly.
    • Locate within 165 feet (50 meters) of each other
      If located farther away, the devices may have trouble connecting.
    • Away from large solid objects
      Thick walls, metal surfaces, concrete, or other objects may limit wireless communication.
    • At least 3 feet (0.9 meters) away from electronic devices
      Televisions, computers, microwaves, radios, and other electronic devices may cause wireless interference.

  • Where to Place the Indoor Display
    Be sure to remove the protective film from its LCD screen, locate the tab and peel off the film.
    • Place on a flat surface or mount to a solid wall surface in dry area free of dirt and dust
    • Keep out of direct sunlight
    • Keep away from heat sources
Where to Place the Wireless Outdoor Sensor
  • In a well-shaded area, away from direct sunlight
    When placed in direct sunlight, the heat from the sun may cause the temperature readings to be higher than the actual ambient air temperature. The best location is commonly on the north side of your home.
  • 4 to 8 feet (1. 2 to 2.4 meters) above the ground Too low and it will pick up excess heat from the ground. Too high and it will cool from the wind.
  • In an area that has good airflow
    This keeps the air circulating freely around the sensor. If placed too close to a solid object, the readings may not be accurate.
  • Above a natural (grassy or dirt) surface
    Concrete, pavement, and stone absorb heat and will impact readings.
  • Protected from direct weather elements
    The sensor is water-resistant and for general outdoor use. Weather elements, such as rain or snow, or a damp or excessively humid area, may damage the device.
How to Mount the Wireless Outdoor Sensor
  • Using the mounting hanger:
    attach a string (not included) to its mounting hanger and secure string to a solid object, such as a tree branch.

  • STEP 5
    Verify Wireless Connection and Signal Strength
    • Verify the Indoor Display shows the Outdoor Conditions
    • After placing the Wireless Outdoor Sensor, it may take up to five (5) minutes to display the Outdoor Conditions.
    • Verify the Wireless Outdoor Sensor red LED flashes every 30 seconds, which indicates readings are being sent to the Indoor Display.
    • From the Indoor Display, verify the Wireless Outdoor Sensor signal strength.

SPECIFICATIONS

  • Temperature range
    Indoor temperature: 32º to 122º F / 0º to 50º C Outdoor temperature: -40º to 158º F / -40º to 70º C
  • Humidity range
    1% to 99% Relative Humidity (RH)
  • Wireless communication
    433 MHz wireless radio frequency (RF)
  • Wireless signal range
    Up to 165 feet (50 meters)
  • Power
    Indoor Display: three AAA alkaline batteries
    Wireless Outdoor Sensor: two AA alkaline or lithium batteries
  • Display update interval
    Indoor conditions: every 60 seconds Outdoor conditions: every 30 seconds

TROUBLESHOOTING

    PROBLEM                  CAUSE                       CORRECTION                                                                             
No bars shown

 

 

 

 

 

 

 

 

 

No wireless connection between devices Verify device locations and low battery indicator:

•   Verify the devices are within 165 feet (50 meters) of each other. You may need to relocate the Indoor Display or Wireless Outdoor Sensor to get a better signal strength.

•   Verify both devices are located 3 feet (0.9 meters) away from electronics that may interfere with their wireless signal, such as televisions, microwaves, or computers.

•   If a low battery indicator       is shown, replace the device batteries. Be sure to use high-quality alkaline batteries. Heavy duty or rechargeable batteries are not recommended. Only use Lithium batteries in the Wireless Outdoor Sensor when the outdoor temperature is below -4ºF/-20ºC for extended periods of time.

When batteries are replaced, it may take up to five (5) minutes for the devices to establish a wireless connection. When connected, the Indoor Display will show the Outdoor Conditions.

Outdoor Conditions readings are flashing or showing dashes (—) Wireless interference or loss of signal Reset devices’ wireless connection:

1.   Bring the Wireless Outdoor Sensor indoors and place it within 2 feet (0.6 meters) from the Indoor Display.

2.   Remove one battery from both devices.

3.   Reinsert the Wireless Outdoor Sensor battery.

4.   Reinsert the Indoor Display battery. The display searches for and wirelessly connects to the Wireless Outdoor Sensor.

5.   Let the devices sit within a couple of feet of each other for approximately five (5) minutes to establish a strong wireless connection.

Inaccurate temperature Device location affecting its readings Verify both devices are not located:

•   In direct sunlight.

•   Near heat sources such as vents, stoves, or other elements that emit heat.

•   On or near a window or other uninsulated surface, such as a brick wall, that can get much warmer or cooler.

•   In a confined location where the air may not circulate enough.

Indoor Display is blank No battery power Verify batteries are installed correctly. You may need to replace the batteries.

 

Note

When the Indoor Display batteries are replaced or after a loss of battery power, you will need to reset its time, date, and temperature units.

 

When batteries are replaced or after a loss of battery power, it may take up to five (5) minutes for the devices to reestablish their wireless connection. When

connected, the Indoor Display will show the Outdoor Conditions and the Wireless Outdoor Sensor red LED

REGISTER ONLINE

Thank you for your purchase. Register your product now for:

  • WARRANTY SERVICE: Registering your product will help you obtain more efficient warranty service in case there is a problem with your product.
  • CONFIRMATION OF OWNERSHIP: In case of an insurance loss, such as fire, flood or theft, your registration of ownership will serve as your proof of purchase.
  • FOR YOUR SAFETY: Registering your product will allow us to contact you in the unlikely event a safety notification is required under the Federal Consumer Safety Act.
    Register online at www.craftsman.com/registration

REGULATORY INFORMATION

FCC Radio Frequency Interference
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
To assure continued appliance, any changes or mo ons not expressly approved by the party responsible for compliance could voice the user’s authority to operate this equipment. (Example -use only shielded interface cables when connecting to computer or peripheral devices).

FCC Warning
Any Changes or mod ons not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two condition

  1. this device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

Canada Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

  1. This device may not cause interference.
  2. This device must accept any interference, including interference that may cause undesired operation of the device.

The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance.

One Year Limited Warranty

CRAFTSMAN will repair or replace, without charge, any defects due to faulty materials or workmanship for one year from the date of purchase. This warranty does not cover part failure due to normal wear or tool abuse. For further detail of warranty coverage and warranty repair information, visit www.craftsman.com or call 1-888-331-4569. This warranty does not apply to accessories or damage caused where repairs have been made or attempted by others.

THIS LIMITED WARRANTY IS GIVEN IN LIEU OF ALL OTHERS, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND EXCLUDES ALL INCIDENTAL OR CONSEQUENTIAL DAMAGES.

Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so these limitations may not and you may have other rights which vary in certain states or provinces.
90 DAY MONEY BACK GUARANTEE

your CRAFTSMAN Wireless Thermometer for any reason, you can return it within 90 days from the date of purchase with a receipt for a full refund – no questions asked.
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products sold in Latin America,
packaging, call the local company or see website for warranty information.

CRAFTSMAN®
is a registered trademark of Stanley Black & Decker, Inc., used under license. © 2020 CRAFTSMAN
Product Manufactured by:
Chaney Instrument Company
Lake Geneva, WI 53147
U.S. & Canada Only