Acer AMR030 MOUSE RS User Guide

PORSCHE DESIGN
ACER MOUSE RS
Quick Start Guide

Package Contents

• Bluetooth & Wireless mouse x 1
• Quick start guide x 1
• Warranty booklet x 1
• Battery x 2

Device Overview

1. Left button
2. Scroll wheel (3D)
3. Right button
4. Nano USB receiver
5. LED indicator
6. Optical sensor
7. Bluetooth button (mode switch)
8. USB receiver holder
9.  Battery compartments

Turn the mouse on

1. Open the battery compartment cover at the back of the mouse.
2. Install 2 AAA batteries into the battery compartments.
3. Replace the cover.
4. The mouse is automatically ON.

WARNING
Make sure that the positive and negative ends are positioned correctly as labeled on the battery compartment.
Connect your mouse

• Using the Nano USB receiver
  Plug the Nano USB receiver into your computer s USB Type-A port. Now you are ready to use the mouse.

NOTE
It’s Plug & Play connectivity, no drivers are required. Make sure the distance between your computer and the mouse is within 10 meters.

• Pairing your mouse with Bluetooth

1. Press and hold the Bluetooth button at the back of your mouse for 2 seconds to switch to Bluetooth mode and start the initial pairing process. Press and hold the Bluetooth button for 5 seconds will start the pairing process again (or pairing with new device).
2. The LED starts to flash blue indicating that the mouse is in Bluetooth mode and ready to pair.
3. Start the Bluetooth pairing wizard on your computer and follow the instructions.

NOTE
– Once your mouse is paired successfully, you do not need to pair it again when using the mouse next time.
– If the pairing is unsuccessful, your mouse will enter Sleep mode after flashing blue for about 3 minutes.
Please repeat steps 1-3 above to restart the pairing process.
Mode switch
Press the Bluetooth button for 2 seconds to toggle your mouse between Wireless and Bluetooth mode. LED flashes blue for 3 seconds indicating that the mouse is in Bluetooth
mode. LED flashes red for 3 seconds indicating the mouse is in Wireless mode.
DPI switch
You can cycle through the DPI options by repeatedly pressing the Bluetooth button for 1 second.
There are three available options for selection: 800/1600/3200.
Low battery notification
When the battery level is low, the flashing red will stay on if the mouse is in use. After stopping using the mouse, the LED flashes red for 10 seconds and then off.
NOTE
The mouse will maintain a low current consumption when entering Sleep mode. It is recommended to remove batteries if the mouse will not be used for an extended period.

Specifications

• Model: AMR030
• Operation System: Windows ® 7 or later (Windows® 8 or later / Mac OS X or later are required for BT feature)
• Bluetooth: 5.0 or later
• Connection Type: RF & BT
• Interface: USB Type-A port (Dongle)
• DPI: 800/1600/3200
• Weight: 92g ± 5g (with AAA battery x2)
• Dimensions (L x W x H): 114.3 x 60 x 27.36 mm

Caution

• Do not disassemble the device or operate the device under abnormal conditions.
• Do not submerge the device in water.
• If the device could not be functional, or there was a thermal abnormal situation, please re-plug in the USB.
• If you still encounter problems after going through the corrective measures, please contact your dealer or an authorized service center for assistance.
• For more information, please visit our website at www.acer.com.

Environment

Temperature:

• Operating: 5 °C to 40 °C
• Non-operating: -10 °C to 70 °C

Humidity (non-condensing):

• Operating: 10% to 60%
• Non-operating: 10% to 60%

Manufacturer address

Acer Inc.
8F, 88, Sec. 1, Xintai 5th Rd. Xizhi, New Taipei City 221, Taiwan
NOTE
All images and information in this document are for reference only and are subject to change without notice. For the latest specification, please visit our official website: www.acer.com.

Europe – EU Declaration of Conformity
We declare under our sole responsibility that the product is in conformity with all the essential requirements and other provisions of the European Council Directive RoHS Directive (2011/65/EU) and Radio Equipment Directive (2014/53/EU) issued by the Commission of the European Community.
This product must not be disposed of with your other household waste or treated in compliance with the local regulations or contact your local city office, your household waste disposal service or the shop where you purchased the product.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
  FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Radiation Exposure Statement

The product complies with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. Further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available.
Notice: Canadian users
Canada, Industry Canada (IC) Notices
This device complies with Industry Canada license-exempt RSS standard(s).
This Class B digital apparatus complies with Canadian ICES-003 and CAN ICES-3(B)/NMB- 3(B).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. End-users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with ISED exposure compliance requirements, please follow operation instructions as documented in this manual.

www.acer.com