Nokia TA-1319 Mobile Phone User Guide

Nokia TA-1319 Mobile Phone

For your safety

Read these simple guidelines. Not following them may be dangerous or against local laws and regulations. For further information, read the complete user guide.

SWITCH OFF IN RESTRICTED AREAS
Switch the device off when mobile phone use is not allowed or when it may cause interference or danger, for example, in aircraft, in hospitals or near medical equipment, fuel, chemicals, or blasting areas. Obey all instructions in restricted areas.

ROAD SAFETY COMES FIRST
Obey all local laws. Always keep your hands free to operate the vehicle when driving. Your first consideration while driving should be road safety.

INTERFERENCE
All wireless devices may be susceptible to interference, which could affect performance.

AUTHORIZED SERVICE
Only authorized personnel may install or repair this product.

BATTERIES, CHARGERS, AND OTHER ACCESSORIES
Use only batteries, chargers, and other accessories approved by HMD Global for use with this device. Do not connect incompatible products.

KEEP YOUR DEVICE DRY
Your device is not water-resistant. Keep it dry.

PROTECT YOUR HEARING
To prevent possible hearing damage, do not listen at high volume levels for long periods. Exercise caution when holding your device near your ear while the loudspeaker is in use.

SAR

This device meets RF exposure guidelines when used either in the normal use position against the ear or when positioned at least 5 mm (0.2 inches) away from the body. The specific maximum SAR values can be found in the Certification Information (SAR) section of this user guide. For more info, go to www.sar-tick.com.
When a carry case, belt clip or another form of device holder is used for body-worn operation, it should not contain metal and should provide at least the above-stated separation distance from the body. Note that mobile devices may be transmitting even if you are not making a voice call.

Keys and parts

  1. Call key
  2. Left selection key
  3. Scroll key. Press to access your apps and select items.
  4. Earpiece/Loudspeaker
  5. USB connector
  6. Flashlight
  7. headset connector
  8. Camera
  9. Back cover opening slot
  10.  Right selection key
  11.  End/Power key
  12.  Microphone
  13. To lock the keys, select Go to > Lock keypad.
  14. To unlock the keys, select Unlock.

Avoid touching the antenna area while the antenna is in use. Contact with antennas affects the communication quality and may reduce battery life due to higher power level during operation.
Do not connect to products that create an output signal, as this may damage the device. Do not connect any voltage source to the audio connector. If you connect an external device or headset, other than those approved for use with this device, to the audio connector, pay special attention to volume levels.

Parts of the device are magnetic. Metallic materials may be attracted to the device. Do not place credit cards or other magnetic stripe cards near the device for extended periods of time, since the cards may be damaged. Some of the accessories mentioned in this user guide, such as charger, headset, or data cable, may be sold separately.
Note: You can set the phone to ask for a security code. The pre-set code is 12345. Change it to protect your privacy and personal data. Note, however, that when you change the code, you need to remember the new code, as HMD Global is not able to open or bypass it. This phone cannot be located or locked remotely if lost.

Insert the SIM, memory card, and battery

Use only original mini-SIM cards. Use of incompatible SIM cards may damage the card or the device, and may corrupt data stored on the card.
Use only compatible memory cards approved for use with this device. Incompatible cards may damage the card and the device and corrupt data stored on the card. Note: Switch the device off and disconnect the charger and any other device before removing any covers. Avoid touching electronic components while changing any covers. Always store and use the device with any covers attached.

  1. Put your fingernail in the small slot at the bottom of the phone, lift and remove the cover.
  2. If the battery is in the phone, lift it out.
  3. Slide the SIM card into the SIM1 slot with the contact area face down. If you have a second SIM, slide it into the SIM2 slot. Both SIM cards are available at the same time when the device is not being used, but while one SIM card is active, for example, making a call, the other may be unavailable. 
  4. If you have a memory card, slide it in the memory card slot.
  5. Line up the battery contacts, and put the battery in.
  6. Put back the cover.
    Important: Do not remove the memory card when an app is using it. Doing so may damage the memory card and the device and corrupt data stored on the card.

Switch your phone on or off
Press and hold the power key.

Charge the battery

  1. Plug the charger into the wall outlet.
  2. Connect the charger to the phone. When done, unplug the charger from the phone then from the wall outlet.

If the battery is completely discharged, it may take several minutes before the charging indicator is displayed.

Camera

Take a photo.

  1. To switch the camera on, select Menu >
  2. To zoom in or out, scroll up or down.
  3. To take a photo, press the scroll key.

Listen to radio
To listen to the radio, you need to connect a compatible headset to the device. The headset acts as an antenna.
Search for radio stations and listen to radio Select Menu >. When the phone asks if you want to search all available channels, select OK.

Find your model number and serial number (IMEI)
If you need to contact your care point or your service provider, you may need info such as the model number and the serial number (IMEI). To see the model number, dial *#0000#. To see the serial number, dial *#06#.
If you have a dual SIM phone, only IMEI1 is needed. You can also find the info on your phone label, which is located under the battery.
The IMEI is also visible on the original sales box.

Product and safety info
For info on HMD Global Privacy Policy, go to www.nokia.com/phones/privacy. For the online user guide, even more info, and troubleshooting help, go to www.nokia.com/mobile-support.
Network services and costs
You can use your device on the GSM 850, 900, 1800, and 1900 networks. You need a subscription with a service provider.

Take care of your device

Handle your device, battery, charger and accessories with care. The following suggestions help you keep your device operational.

  • Keep the device dry. Precipitation, humidity, and all types of liquids or moisture can contain minerals that corrode electronic circuits. If your device gets wet, remove the battery, and let the device dry.
  • Do not use or store the device in dusty or dirty areas.
  • Do not store the device in high temperatures. High temperatures may damage the device or battery.
  • Do not store the device in cold temperatures. When the device warms to its normal temperature, moisture can form inside the device and damage it.
  • Do not open the device other than as instructed in the user guide.
  • Unauthorized modifications may damage the device and violate regulations governing radio devices.
  • Do not drop, knock, or shake the device or the battery. Rough handling can break it.
  • Only use a soft, clean, dry cloth to clean the surface of the device.
  • Do not paint the device. Paint can prevent proper operation.
  • For optimal performance, switch the device off and remove the battery from time to time.
  • Keep the device away from magnets or magnetic fields.
  • To keep your important data safe, store it in at least two separate places, such as your device, memory card, or computer, or write down important info.

Restore original settings
To reset your phone to its original settings and to remove all your data, on the home screen, type in *#7370#.

Recycle

When this device has reached the end of its working life, all of its materials can be recovered as materials and energy. Recycle packaging and user guides at your local recycling scheme. When you cooperate and deliver all these materials to one of the available collection sites, you contribute in helping the environment and help to ensure the health of future generations.
All electrical and electronic products and batteries may contain recyclable metals and other potentially hazardous substances and must be taken to their respective collection sites at the end of their working life. Under no circumstances should you break open a battery or other related materials. Do not dispose of these products as unsorted municipal waste, as this may cause contamination of the environment or risks to human health. All HMD Global products are in compliance with the applicable industry international production standards and to all requirements defined by the competent government agencies.

Crossed-out wheelie-bin symbol
The crossed-out wheelie-bin symbol on your product, battery, literature, or packaging reminds you that all electrical and electronic products and batteries must be taken to separate collection at the end of their working life. Do not dispose of these products as unsorted municipal waste: take them for recycling. For info on your nearest recycling point, check with your local waste authority.

Battery and charger info
Use your device only with an original BL-5CB rechargeable battery. Charge your device with the AC-18 charger. Charger plug type may vary. HMD Global may make additional battery or charger models available for this device.

Electrical Information of the Charger
The following electrical information corresponds to the above-mentioned charger models:
Input: 100 Vca – 240 Vca, 50 Hz a 60 Hz, 0,1 A
Output: 5 Vcc, 0,55 A

Charger safety instructions
The charger is suitable to be used only with compatible devices. The charger should not be used in extremely high or low temperatures.
Ventilation should not be obstructed by covering the charger with magazines, blankets, curtains etc.
Open flames, such as candles, should not be placed above the charger.
The charger and the wall outlet shall be easily accessible at all times. In case the cable or the plugs are damaged, stop using it.
The charger requires very low maintenance. If you want to clean it, use a dry cloth or a brush.

Meaning of the symbols
For internal use, only The charger should not be disposed as unsorted municipal waste. It should be recycled. 

Battery and charger safety
Always switch the device off and unplug the charger before removing the battery. To unplug a charger or an accessory, hold and pull the plug, not the cord.
When your charger is not in use, unplug it. If left unused, a fully charged battery will lose its charge over time.
Always keep the battery between 15°C and 25°C (59°F and 77°F) for optimal performance. Extreme temperatures reduce the capacity and lifetime of the battery. A device with a hot or cold battery may not work temporarily.

Accidental short-circuiting can happen when a metallic object touches the metal strips on the battery. This may damage the battery or the other object.
Do not dismantle, cut, crush, bend, puncture, or otherwise damage the battery in any way. If a battery leaks, do not let liquid touch skin or eyes. If this happens, immediately flush the affected areas with water, or seek medical help. Do not modify, attempt to insert foreign objects into the battery, or immerse or expose it to water or other liquids. Batteries may explode if damaged.

Use the battery and charger for their intended purposes only. Improper use, or use of unapproved or incompatible batteries or chargers may present a risk of fire, explosion, or another hazard, and may invalidate any approval or warranty. If you believe the battery or charger is damaged, take it to a service centre before continuing to use it. Never use a damaged battery or charger. Only use the charger indoors. Do not charge your device during a lightning storm.
Do not dispose of batteries in a fire as they may explode. Obey local regulations. Recycle when possible. Do not dispose as household waste.

Small children
Your device and its accessories are not toys. They may contain small parts. Keep them out of the reach of small children.

Medical devices
Operation of radio transmitting equipment, including wireless phones, may interfere with inadequately shielded medical devices’ function. Consult a physician or the medical device’s manufacturer to determine if it is adequately shielded from external radio energy.

Copyrights and other notices

FCC notice:
This device complies with part 15 of the FCC rules and standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For more info, go to www.fcc.gov/engineering-technology/electromagnetic-compatibility-division/radio-frequency-safety/faq/rf-safety. Any changes or modifications not expressly approved by HMD Global could void the user’s authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Manufacturer and/or importer in EU: HMD Global Oy, Bertel Jungin aukio 9, 02600 Espoo, Finland.
HMD Global Privacy Policy, available at http://www.nokia.com/phones/privacy, applies to your use of the device.
© 2020 HMD Global. HMD Global Oy is the exclusive licensee of the Nokia brand for phones & tablets. Nokia is a registered trademark of Nokia Corporation.
This product includes open-source software. For applicable copyright and other notices, permissions, and acknowledgments, select
*#6774# on the home screen.

Manufacturer’s limited warranty

  1. General
    HMD Global Oy (hereinafter “Manufacturer”) provides this Manufacturer’s Limited Warranty (“Warranty”) for the genuine Nokia mobile phone (“Product”) which has been released for sale in Latin America and the Caribbean.
    Even though one or more countries may be mentioned herein, this Warranty is valid only in the country where the Product was purchased through the Manufacturer’s authorized sales channels, provided that the Product was intended for sale in that country
    (“Covered Country”).
    This Warranty covers and includes any statutory rights under any mandatory consumer protection laws of the Covered Country applicable to you, and also grants you specific, and as the case may be, additional rights, within the limits of what is permissible under such law. This Warranty does not limit the rights you may have under applicable consumer protection laws. You may have other rights based on local laws during or after the Warranty period. These rights are not excluded by this Warranty.
    The Product and its accessories shall be used in accordance with the instructions provided in the user guides and leaflets that come in the Product package and are also available at www.nokia.com/mobile-support.
  2. Warranty
    The Warranty period starts on the date the Product is sold to an end-user for the first time, as evidenced by the original proof of purchase. Said first purchaser and anyone who subsequently acquires the Product during the original warranty period will be entitled to the warranty rights.
    Manufacturer agrees to cover under warranty defects in materials and workmanship employed in Product manufacturing (“Defect”) for:
    1.  Twelve (12) months for the main device; and
    2. Six (6) months for the battery, charger, headset and any other accessory included in the sales package of the main device,
      unless the law requires that the manufacturer offers a longer period, in which case the Warranty period is extended to cover the minimum period required by the law.
      The Warranty period described above includes any mandatory Warranty term you may have in the Covered Country. As a consequence, the first month(s) of the Warranty period described above correspond to the mandatory Warranty term in the Covered Country and the remaining months until completion of the period described above correspond to the contractual Warranty term granted by the Manufacturer.
      During the Warranty period, any Defect covered by this Warranty will be remedied within a reasonable time, free of charge, through the replacement of the Product or accessory affected by the Defect. During the Warranty period, in case you suspect that your Product or any accessory has a Defect, please take it back to the point of sale where the Product has been purchased. The seller will perform a preliminary analysis on the Product or accessory and if found to be defective, the Product or accessory will be replaced. When replacing your Product, the Manufacturer may use new or reconditioned parts or Products except where the use of such re-conditioned parts or Product is barred by local law. In case local law should require the end-user to be informed about the use of reconditioned parts or Products, this Warranty document can be considered as the necessary notice in that regard. In case local law requires consent from the end-user for the use of reconditioned parts or Products, then such parts or Products will not be used till such consent has been obtained. When making a warranty claim, you must present:
  3. What this Warranty does not cover
    The manufacturer does not provide any warranty for the following:
    1. errors or damages caused by:
      (a) exposure to liquid (unless the Product is declared to be water-resistant under certain conditions as specified by the manufacturer), to extreme electromagnetic field (such as damages caused by microwave oven), to dampness, to extreme thermal or environmental conditions or to rapid changes in such conditions, corrosion, oxidation, spillage of food or liquid, or to influence from chemical products;
      (b) physical damage, cracks, dents or scratches caused by a drop or by external forces occurring in or on the product including but not using your Product with, or connecting it to, any product, accessory, software, or service not manufactured or supplied by the Manufacturer;
      (d) any products combined with your Product by a third party;
      (e) damage or errors caused by hacking, cracking, viruses, or other malware, or by unauthorized access to services, accounts, computer systems, or networks;
      (f) power outages or surges capable of affecting the normal use of the Product; or
      (g) other acts beyond the Manufacturer’s reasonable control.
    2. If your Product’s serial number, the mobile accessory date code, or the IMEI number has been removed, erased, defaced, altered or if these are illegible in any way;
    3. Any wear and tear;
    4. Not using your Product in accordance with the user guide;
    5. If your Product, has been opened, repaired or modified by non-authorized third parties, or repaired with unauthorized spare parts;
    6. If you have not installed the latest software updates that are publicly available for your Product within a reasonable time of their release; and/or
    7. This Warranty is not valid outside of the Covered Country and doesn’t cover
      (a) User guides;
      (b) Any third party software, settings, content, data, or links installed or downloaded onto your Product at any time, or Manufacturer and third-party services or enabling clients even if preinstalled by Manufacturer (please read the terms and conditions that may accompany the services as those will define your rights and obligations);
      (c) Reduced charging capacity of the battery resulting from its natural end of Product life, or pixel defects in your Product’s display that are within the scope of industry standards; and
      (d) SIM card and/or any cellular or other networks or system on which your Product operates.
  4. Limitation of Manufacturer’s liability
    To the extent permitted by applicable law(s), the Manufacturer shall not under any circumstances be liable, either expressly or implicitly, for any:
    (i) Damages or losses of any kind whatsoever resulting from or relating to loss of, damage to, or corruption of, content or data or the re-creation or transfer thereof even if such loss, damage, or corruption was a result of (a) a Defect in your Product; or (b) an attempt to repair your Product; and/or(a) a Defect in your Product; or (b) an attempt to repair your Product; and/or (ii) Loss of profit, productivity, functionality, business, contracts, revenues or anticipated savings, increased costs or expenses, or for any indirect, consequential or special loss or damage. To the extent permitted by applicable law, the Manufacturer’s liability shall be limited to the purchase value of your Product. The limitations in this clause 4 shall not apply in case of the Manufacturer’s negligence or intentional misconduct or in case of death or personal injury resulting from the Manufacturer’s proven negligence.
  5. Other important notices
    For any further information related to your Product and how to enforce the Warranty, please visit www.nokia.com/mobile-support. Your Product may contain country-specific elements, including software. Also, if your Product has been re-exported from its original destination to another country, your Product may contain country-specific elements that are not considered a Defect under this Warranty even if those elements or the Product would not be operational.
  6. Additional information
    Manufacturer and Warranty provider: HMD Global Oy (address: Bertel Jungin aukio 9, 02600 Espoo, Finland) Information to be filled in by the seller if required by local law: Product model and IMEI: Seller name and address: Product acquisition and delivery date(s): End-user name and address: