KENWOOD BM250 RAPID BAKE BREAD MAKER User Manual

KENWOOD BM250 RAPID BAKE BREAD MAKER

before using your Kenwood appliance

  •  Read these instructions carefully and retain for future reference.
  •  Remove all packaging and any labels. safety
  •  Do not touch hot surfaces. Accessible surfaces are liable to get hot during use. Always use oven gloves to remove the hot bread pan.
  •  To prevent spillages inside the oven chamber, always remove the bread pan from the machine before adding the ingredients. Ingredients that splash onto the heating element can burn and cause smoke.
  •  Do not use this appliance if there is any visible sign of damage to the supply cord or if it has been accidentally dropped.
  •  Do not immerse this appliance, the supply cord or the plug in water or any other liquid.
  • Always unplug this appliance after use, before fitting or removing parts or before cleaning.
  •  Do not let the electrical supply cord hang over the edge of a work surface or allow it to touch hot surfaces such as a gas or electric hob.
  •  This appliance should only be used on a flat heat resistant surface.
  •  Do not place your hand inside the oven chamber after the bread pan has been removed as it will be very hot.
  •  Do not touch moving parts within the Bread Maker.
  •  Do not exceed the maximum capacity (1Kg) stated as this could result in over-loading the Bread Maker.
  •  Do not place the Bread Maker in direct sun light, near hot appliances or in a draught. All these things can affect the internal temperature of the oven, which could spoil the results.
  •  Do not use this appliance outdoors.
  •  Do not operate the Bread Maker when it is empty as this could cause it serious damage.
  •  Do not use the oven chamber for any type of storage.
  •  Do not cover the steam vents in the lid and ensure there is adequate ventilation around the bread maker during operation.
  •  Do not let infirm people use the appliance without supervision.
  •  Do not let children use or play with the appliance.
  •  Only use the appliance for its intended domestic use.
  • Kenwood will not accept any liability if the appliance is subject to improper use, or failure to comply with these instructions. before plugging in
  •  Make sure your electricity supply is the same as the one shown on the underside of your Bread Maker.
  •  This machine complies with European Economic Community Directive 89/336/EEC before using your bread maker for the first time
  •  Wash all parts (see care and cleaning).

PRODUCT FEATURES

key

  • lid handle
    • viewing window
  • heating element
    • bread pan handle
  • kneader
    •  drive shaft
  • drive coupling
    •  on/off switch
    •  measuring cup
    •  dual measuring spoon 1tsp & 1tbsp
  •  control panel
    • display window
    •  timer indicator
    •  program status indicator
    •  crust colour indicators (light, medium, dark, rapid)
    •  delay timer buttons
    •  loaf size button
    •  start/stop button
    •  rapid bake button
    •  crust colour button
  • menu button
  • loaf size indicators

how to measure ingredients

(refer to illustrations 3 to 7)

  • It is extremely important to use the exact measure of ingredients for best results.
  •  Always measure liquid ingredients in the see-through measuring cup with graduated markings provided.
  • Liquid should just reach marking on cup at eye level, not above or below (see 3).
  •  Always use liquids at room temperature, 20ºC/68ºF, unless making bread using the rapid 1 hour cycle. Follow the instructions given in the recipe section.
  •  Always use the measuring spoon provided to measure smaller quantities of dry and liquid ingredients. Use the slider to select between the following measure – 1⁄2 tsp, 1 tsp, 1⁄2 tbsp or 1 tbsp. Fill to the top and level off the spoon (see 6 & 7). on/off switch
  • Your Kenwood breadmaker is fitted with an ON/OFF switch and will not operate until the “on” switch is pressed.
  •  Plug in and press the ON/OFF switch situated at the back of the breadmaker – the unit will beep and 3:25 will appear in the display window.
  •  Always switch off and unplug your breadmaker after use.

program status indicator 

  • The program status indicator is situated in the display window and the indicator arrow will point to the stage of the cycle the breadmaker has reached as follows: –
  • Pre-heat – The pre-heat feature only operates at the start of the wholewheat setting (30 minutes wholemeal and 5 minutes wholemeal rapid) to warm the ingredients before the first kneading stage begins.
  • There is no kneader action during this period.
  • Knead – The dough is either in the first or 2nd kneading stage or being knocked back between the rising cycles. During the last 10minutes of the 2nd
  • Kneading cycle on setting (1), (3), (4) an alert will sound to tell you to add any additional ingredients manually.
  • Rest – dough is being rested between the kneading cycles.
  • Rise – the dough is in either the 1st, 2nd or 3rd rising cycle.
  • Bake – The loaf is in the final baking cycle.
  • Keep Warm – The bread maker automatically goes into the Keep warm mode at the end of the baking cycle. It will stay on the keep warm mode for up to
  • 1hour or until the machine is turned off, which ever is soonest. Please note: the heating element will switch on and off and will glow intermittently during the keep warm cycle.
  • End – end of program.

using your Bread Maker (refer to illustration panel)

  • Lift out the bread pan by the handle.
  • Fit the kneader.
  • Pour the water into the bread pan.
  • Add the rest of the ingredients to the pan in the order listed in the recipes. Ensure that all the ingredients are weighed accurately
  • as incorrect measures will produce poor results.
  • Insert the bread pan into the oven chamber and push down to ensure it is locked in position.
  • Lower the handle and close the lid.
  • Plug in and switch on – the unit will beep and default to setting 1 (3:25).
  • Press the MENU button until the required program is selected. The breadmaker will default to 1Kg & medium crust colour. Note: If using the “RAPID BAKE” , just press the button and the program will start automatically.
  •  Select the loaf size by pressing the LOAF SIZE button
    • until the indicator moves to the required loaf size.
  • Select the crust colour by pressing the CRUST button
    • until the indicator moves to the required crust colour (light, medium or dark).
  • Press the START button . To stop or cancel the program press the START/STOP button for 2 – 3 seconds.
  • At the end of the baking cycle unplug the breadmaker
  • Lift out the bread pan by the handle. Always use oven gloves as the pan handle will be hot.
  • Then turn out onto a wire rack to cool.
  •  Leave the bread to cool for at least 30 minutes before slicing, to allow the steam to escape. The bread will be difficult to slice if hot.
  •  Clean the bread pan and kneader immediately after use (see care and cleaning).

bread/dough program chart

bread/dough program chart
program  

Total Program Time

Alert For Adding

Ingredients ✬✬

Keep Warm

✬✬✬

500g 750g 1Kg 500g 750g 1Kg
1 basic White or Brown Bread Flour recipes 3:13 3:18 3:25 2:51 2:56 3:03 60
2 french Produces a crisper crust and suited to loaves low in fat and sugar 3:30 3:32 3:35 60
Rapid Loaves ✬ 2:30 2:32 2:35
3 wholewheat Wholewheat or wholemeal flour recipes: 30 minute preheat 3:43 3:45 3:48 2:56 2:58 3:01 60
Rapid Loaves: 5 minute preheat ✬ 2:28 2:30 2:33
4 sweet High sugar bread recipes 3:17 3:22 3:27 2:55 3:00 3:05 60
5 gluten free For use with gluten free flours and gluten free bread mixes. Max 500g flour wt 2:24 60
6 packet mix For ready prepared bread mixes Max 500g mix 2:24 60
7 cake Non-yeast batter breads and cakes 1:43
8 dough Dough for hand shaping and baking in your own oven. 1:30
9 pasta dough Pasta dough recipes 0:14
10 jam For making jams 1:05
11 bake Bake only feature. Can also be used to rewarm or crisp loaves already baked and cooled. 1:00 60
rapid bake button Produces loaves of bread in under 1 hour. Loaves require warm water, extra yeast and less salt. 0:58 60

delay timer

The Delay timer allows you to delay the bread making process up to 15 hours. The delayed start cannot be used with the “RAPID BAKE” program and is not recommended for use with either the dough, jam or gluten free settings.
IMPORTANT: When using this delayed start function you must not use perishable ingredients – things that ‘go off’ easily at room temperature or above, such as milk, egg, cheese and yoghurt etc. To use the DELAY TIMER simply place the ingredients in the bread pan and lock the pan into the bread maker. Then:

  • Press the MENU pad to choose the required program – the program cycle time is displayed.
  • Select the crust colour and size required.
  • Then set the delay timer.
  • Press the (+) TIMER pad and keep pressing until the total time required is displayed. If you go past the required time press the (-) TIMER pad to go back. The timer pad when pressed, moves in 10 minute increments. You do not need to work out the difference between the program time selected and the total hours required as the bread maker will automatically include the setting cycle time.
    Example: Finished loaf required at 7am. If the breadmaker is set up with the required recipe ingredients at 10pm the evening before, total time to be set on the delayed timer is 9 hours.
  • Press the MENU pad to choose your program e.g. 1 and use the (+) timer pad to scroll the time in 10 minute increments to display ‘9:05’.
    If you go past ‘9:05’, simply press the (-) timer pad until you return to ‘9:05’.
  • Press the start pad and the display colon (:) will flash. The timer will start to count down.
  • If you make a mistake or wish to change the time set, press the START/STOP pad until it beeps. You can then reset the time.

power interruption protection

  • Your Bread Maker has an 8 minute power interruption protection in case the unit is accidentally unplugged during operation. The unit will continue the program if plugged back in straight away. care and cleaning
  • IMPORTANT: unplug the Bread Maker and allow to cool before cleaning.
  •  Do not immerse either the Bread Maker body or the outside base of the bread pan in water.
  •  Do not use a dishwasher to clean bread pan. Dishwashing can damage the non-stick properties of the bread pan allowing bread to stick during baking.
  •  Do not use abrasive scouring pads or metal implements.
  •  Clean the bread pan and the kneader immediately after each use by partially filling the pan with warm soapy water. Leave to soak for 5 to 10 minutes. To remove the kneader, turn clockwise and lift off. Finish cleaning with a soft cloth, rinse and dry.
  • If the kneader cannot be removed after 10 minutes, hold the shaft from underneath the pan and twist back and forth until the kneader is released.
  •  Use a soft damp cloth to clean the outside and inside surfaces of the Bread Maker if necessary.
  •  The lid can be lifted off for cleaning. service and customer care
  •  If the cord is damaged it must, for safety reasons, be replaced by KENWOOD or an authorised KENWOOD repairer.
  • If you need help with:
  •  using your machine or
  •  servicing or repairs
  •  Contact the shop where you bought your Bread Maker.

Basic White Bread

Ingredients 500g 750g 1Kg
Water 245ml 290ml 380ml
Vegetable oil 1tbsp 1 1 2 tbsp 1 1 2 tbsp
Unbleached white bread flour 350g 450g 600g
Skimmed milk powder 1tbsp 4tsp 2tbsp
Salt 1tsp 1 1 2 tsp 1 1 2 tsp
Sugar 2tsp 1tbsp 4tsp
Easy blend dried yeast 1tsp 11 2tsp 11 2tsp

Brioche Bread

Ingredients 500g 750g 1Kg
Milk 130ml 220ml 260ml
Eggs 1 2 2
Butter, melted 80g 140g 180g
Unbleached white bread flour 350g 500g 600g
Salt 1tsp 1tsp 1 1 2 tsp
Sugar 30g 60g 80g
Easy blend dried yeast 1 1 2 tsp 2tsp 2 1 2 tsp

Wholemeal Seeded Bread

Ingredients 750g 1Kg
Water 300mls 380mls
Vegetable Oil 1tbsp 1 1 2 tbsp
Wholemeal bread flour 400g 500g
Unbleached white bread flour 50g 100g
Skimmed milk powder 4tsp 2tbsp
Salt 1tsp 1 1 2 tsp
Sugar 2tsp 1tbsp
Easy blend dried yeast 1tsp 1tsp
Pumpkin Seeds 3tsp 3tsp
Sunflower seeds 3tsp 3tsp
Poppy seeds 2tsp 3tsp
Lightly toasted sesame seeds 2tsp 3tsp

Rapid White Bread

Ingredients 1Kg
Milk, lukewarm (32-35°C) 420ml
Vegetable oil 1 1 2 tbsp
Unbleached white bread flour 600g
Skimmed milk powder 2tbsp
Salt 1tsp
Sugar 5tsp
Easy blend dried yeast 4tsp

Bread rolls

Ingredients 1Kg
Water 240ml
Egg 1
Unbleached white bread flour 450g
Salt 1tsp
Sugar 2tsp
Butter 25g
Easy blend dried yeast 1 1 2 tsp
For the topping:
Egg yolk beaten with 15ml (1tbsp) water  

1

Sesame seeds and poppy seeds, for sprinkling, optional

troubleshooting guide

PROBLEM POSSIBLE CAUSE SOLUTION
LOAF SIZE AND SHAPE
1. Bread does not rise enough •  Wholemeal breads will be lower than white breads due to less gluten forming protein in whole wheat flour.

•  Not enough liquid.

•  Sugar omitted or not enough added.

•  Wrong type of flour used.

 

 

•  Wrong type of yeast used.

 

•  Not enough yeast added or too old.

 

•  Rapid bread cycle chosen.

 

•  Yeast and sugar came into contact with each other before kneading cycle.

•  Normal situation, no solution.

 

 

•  Increase liquid by 15ml/3tsp.

•  Assemble ingredients as listed in recipe.

•  You may have used plain white flour instead of strong bread flour which has a higher gluten content.

•  Do not use all-purpose flour.

•  For best results use only fast action “easy blend” yeast.

•  Measure amount recommended and check expiry date on package.

•  This cycle produces shorter loaves. This is normal.

•  Make sure they remain separate when added to the bread pan.

2. Flat loaves, no rising. •  Yeast omitted.

•  Yeast too old.

•  Liquid too hot.

 

•  Too much salt added.

•  If using timer, yeast got wet before bread making process started.

•  Assemble ingredients as listed in recipe.

•  Check expiry date.

•  Use liquid at correct temperature for bread setting being used.

•  Use amount recommended.

•  Place dry ingredients into corners of pan and make slight well in centre of dry ingredients for yeast to protect it from liquids.

3. Top inflated – mushroom-like in appearance. •  Too much yeast.

•  Too much sugar.

•  Too much flour.

•  Not enough salt.

 

•  Warm, humid weather.

•  Reduce yeast by 1/4tsp.

•  Reduce sugar by 1tsp.

•  Reduce flour by 6 to 9tsp.

•  Use amount of salt recommended in recipe.

•  Reduce liquid by 15ml/3 tsp and yeast by 1/4 tsp.

4. Top and sides cave in. •  Too much liquid.

 

•  Too much yeast.

 

•  High humidity and warm weather may have caused the dough to rise too fast.

•  Reduce liquid by 15ml/3tsp next time or add a little extra flour.

•  Use amount recommended in recipe or try a quicker cycle next time.

•  Chill the water or add milk straight from the fridge

5. Gnarly, knotted top – not smooth. •  Not enough liquid.

•  Too much flour.

•  Tops of loaves may not all be perfectly shaped, however, this does not affect wonderful flavour of bread.

•  Increase liquid by 15ml/3tsp.

•  Measure flour acurately.

•  Make sure dough is made under the best possible conditions.

PROBLEM POSSIBLE CAUSE SOLUTION
LOAF SIZE AND SHAPE
6.           Collapsed while baking.

 

 

 

 

 

 

 

 

7.           Loaves uneven shorter on one end.

• Machine was placed in a draught or may have been knocked or jolted during rising.

• Exceeding capacity of bread pan.

 

• Not enough salt used or omitted. (salt helps prevent the dough over proving)

• Too much yeast.

• Warm, humid weather.

 

 

• Dough too dry and not allowed to rise evenly in pan.

• Reposition bread maker.

 

 

• Do not use more ingredients than recommended for large loaf (max. 1Kg).

• Use amount of salt recommended in recipe.

• Measure yeast acurately.

• Reduce liquid by 15ml/3tsp and reduce yeast by 1/4tsp.

 

• Increase liquid by 15ml/3 tsp.

BREAD TEXTURE
8. Heavy dense texture. • Too much flour.

• Not enough yeast.

 

• Not enough sugar.

• Measure accurately.

• Measure right amount of recommended yeast.

• Measure accurately.

9. Open, course, holey texture. • Salt omitted.

• Too much yeast.

 

• Too much liquid.

• Assemble ingredients as listed in recipe.

• Measure right amount of recommended yeast.

• Reduce liquid by 15ml/3tsp.

10. Centre of loaf is raw, not baked enough. • Too much liquid.

• Power cut during operation.

 

 

• Quantities were too large and machine could not cope.

• Reduce liquid by 15ml/3tsp.

• If power is cut during operation,for more than 8 minutes you will need to remove the unbaked loaf from the pan and start again with fresh ingredients.

• Reduce amounts to maximum quantities allowed.

11. Bread doesn’t slice well, very sticky. • Sliced while too hot.

 

 

• Not using proper knife.

• Allow bread to cool on rack at least 30 minutes to release steam, before slicing.

• Use a good bread knife.

CRUST COLOUR AND THICKNESS
12. Dark crust colour/ too thick. • DARK crust setting used. • Use medium or light setting the next time.
13. Loaf of bread is burnt. • Bread maker malfunctioning. • Refer to “Service and customer care” section.
14. Crust too light. • Bread not baked long enough.

• No milk powder or fresh milk in recipe.

• Extend baking time.

• Add 15ml/3tsp skimmed milk powder or replace 50% of water with milk to encourage browning.

PROBLEM POSSIBLE CAUSE SOLUTION
PAN PROBLEMS
15.   Kneader cannot be removed.

 

 

16.   Bread sticks to pan/ difficult to shake out.

•  You must add water to bread pan and allow kneader to soak before it can be removed.

 

•  Can happen over prolonged use.

• Follow cleaning instructions after use. You may need to twist kneader slightly after soaking to loosen.

 

• Lightly wipe the inside of bread pan with vegetable oil.

• Refer to “Service and customer care” section.

MACHINE MECHANICS
17. Breadmaker not operating/Kneader not moving. •  Breadmaker not switched on

 

•  Pan not correctly located.

•  Delay timer selected.

• Check on/off switch @ is in the ON position.

 

• Check the pan is locked in place.

• Breadmaker will not start until the countdown reaches the program start time.

18. Ingredients not mixed. •  Did not start bread maker.

 

•  Forgot to put kneader in pan.

• After programming control panel, press start button to turn bread maker on.

• Always make sure kneader is on shaft in bottom of pan before adding ingredients.

19. Burning odour noted during operation. •  Ingredients spilled inside oven.

 

 

•  Pan leaks.

 

•  Exceeding capacity of bread pan.

• Be careful not to spill ingredients when adding to pan. Ingredients can burn on heating unit and cause smoke.

• See “Service and Customer care” section.

• Do not use more ingredients than recommended in recipe and always measure ingredients accurately.

20. Machine unplugged by mistake or power lost during use.

How can I save the bread?.

• If machine is in knead cycle, discard ingredients and start again.

• If machine is in rise cycle, remove dough from bread pan, shape and place in greased 23 x 12.5cm/9 x 5 in. loaf tin, cover and allow to rise until doubled in size. Use bake only setting 11 or bake in pre-heated conventional oven at 200ºC/400ºF/Gas mark 6 for 30-35 minutes or until golden brown.

• If machine is in bake cycle, use the bake only setting 11 or bake in pre-heated conventional oven at 200ºC/400ºF/Gas mark 6 and remove top rack. Carefully remove pan from machine and place on bottom rack in oven. Bake until golden brown.

21. E:01 appears on display and machine cannot be turned on. •  Oven chamber too hot. • Unplug and allow to cool down for 30 minutes.
22. H:HH & E:EE appears in display and

machine does not operate.

•  Bread machine is malfunctioning. Temperature sensor error • See “Service and Customer care” section.