AEG DPS5650AM Cooker Hood User Manual

AEG DPS5650AM Cooker Hood

FOR PERFECT RESULTS 

Thank you for choosing this AEG product. We have created it to give you impeccable performance for many years, with innovative technologies that help make life simpler – features you might not find on ordinary appliances. Please spend a few minutes reading to get the very best from it.
Visit our website to:

CUSTOMER CARE AND SERVICE 

Always use original spare parts.
When contacting our Authorised Service Centre, ensure that you have the following data available: Model, PNC, Serial Number.
The information can be found on the rating plate.

SAFETY INFORMATION AND INSTALLATION

WARNING!
Refer to the separate Installation Instructions booklet for Safety Information and Installation. Read carefully the Safety chapters before any use or maintenance of the appliance.

PRODUCT DESCRIPTION

Control panel overview

Function Description
1 Lamp Turns the lights on and off.
2 Delayed switch off func‐ tion button The function sets automatic switch off delay.
3 Indicator for delayed switch off function Indicates if function is activated.
4 Plus button Increases the fan speed level.
5 LED indicators indicates fan speed levels.
6 Minus button Decreases the fan speed level.
7 Indicator for filter alarm function Indicates if filter alarm is on.

DAILY USE

Using the hood
Check the recommended speed according to the table below.

While heating up food, cooking with covered pots.
While cooking with covered pots on multiple cooking zones or burners, gentle frying.
While boiling and frying big quantities of food without a lid, cooking on multi‐ ple cooking zones or burners.
While boiling and frying big quantities of food without a lid, big humidity. After 8 minutes the appliance returns to previous setting.

It is recommended to leave the hood operating for approximately 15 minutes after cooking.

To operate the hood

  1. Pull out the drawer of the hood more than 5 cm.
    The control panel is exposed.
  2. Press the button to switch on the  hood.
    To increase the fan speed level press the
    button again. Press to decrease the fan speed level.
    The LED indicators on the panel switches on accordingly to selected fan speed level.
    The hoods light works independently to other hood functions. To illuminate the cooking surface touch the light symbol . Closing the drawer has no effect on the hood light.

To turn off the fan continue to press until the hood fan stops or close the hood drawer.

The hood remembers last setting of fan speed on closing the drawer. The hood will operate on this fan speed level when drawer is pulled out again.

Delayed switch-off function

This function allows to automatically turn off the fan after specific time of operating.

  1.  Set the desired fan speed
  2. Press the button.
    The indicator on the panel turns on. To turn off the function press the button again.

The change of the hood fan speed level or closing the hood drawer when the function is activated will result in deactivation of this function.

The time after the function switch off the fan:

  Motor Speed level Time (min)

1                                 20

                                                                    

2                                 15

3                                 10
4                                 8

Filter notification

Filter alarm reminds to change or clean the charcoal filter and clean the grease filter. The LED indicator blinks red regularly for 30 seconds if the grease filter must be cleaned. The LED indicator blinks red twice per every second for 30 seconds if the charcoal filter must be replaced or cleaned.

This function activates independently after 40 hours of operation for grease filter and 160 hours of operation for charcoal filter.

NOTE:

  • The fan does not operate during the alarm. Fan starts to operate on last remembered setting after 30 seconds.
  • Refer to cleaning the grease filter in care and cleaning chapter.
  • Refer to cleaning the charcoal filter or replacing the charcoal filter in care and cleaning chapter.
  • The function counter for charcoal filter is disabled by default.

CARE AND CLEANING

Notes on cleaning

 

Cleaning Agents

 Do not use abrasive detergents and brushes.

Clean the surface of the appliance with a soft cloth with warm water and a mild detergent.

After cooking some parts of appliance can get hot. To avoid stains ap‐ pliance must be cooled down and dried with clean cloth or paper tow‐ els.
Clean stains with a mild detergent.
  • Clean the appliance and grease filters each month. Clean the interior and grease filters carefully from fat. Fat accumulation or other residue may cause fire.
  • Grease filters can be washed in a dishwasher.

    The dishwasher must be set to a low temperature and a short cycle. The grease filter may discolour, it has no influence on the performance of the appliance.

The time of saturation of the charcoal filter varies depending on the type of cooking and the regularity of cleaning the grease filter.

Cleaning the grease filter

Filters are mounted with the use of clips and pins on the opposite side.
To clean the filter:

Press the handle of the mounting clip on the filter panel underneath the hood.

  • Slightly tilt the front of the filter downwards, then pull. Repeat the first two steps for all filters.
  • Clean the filters using a sponge with nonabrasive detergents or in a dishwasher

The dishwasher must be set to a low temperature and a short cycle. The grease filter may discolor, it has no influence on the performance of the appliance.

To mount the filters back follow the first two steps in reverse order. Repeat the steps for all filters if applicable.

Replacing the charcoal filter – optional 

WARNING:

Depending on the type, the filter can be or cannot be regenerated. Refer to the leaflet provided with the filter.

To replace the filter:1. Remove the grease filters from the appliance. Refer to “Cleaning the grease filter” in this chapter.

Pull the tabs towards the bottom part of the filter.

Slightly tilt the front of the filter downwards, then pull.

To install a new filter, perform the same steps in reverse order. In any case, it is necessary to replace the filters at least every four months.

Replacing the lamp
This appliance is supplied with a LED lamp and separate control gear (LED driver). These parts can be replaced by a technician only. In case of any malfunction refer to “Service” in the “Safety Instructions” chapter.

www.aeg.com/shop