Philips BRP130 Smart Bright Road LED Lighting Instruction Manual
PHILIPS BRP130 Smart Bright Road LED Lighting
Mounting Instruction
Type |
LEDs |
Power/W |
CCT/K |
*Light Source Energy Efficiency Class |
Maximum Number of Luminaire on MCB 16A Type B |
Inrush Current |
Voltage |
BRP130 LED88/WW 70W 220-240V DM GM | 82 | 70 | 3000 | D |
50 |
15A/1.5μs |
220-240~ 50/60Hz |
BRP130 LED88/NW 70W 220-240V DM GM | 82 | 70 | 4000 | ||||
BRP130 LED88/CW 70W 220-240V DM GM | 82 | 70 | 5700 | ||||
BRP131 LED125/WW 100W 220-240V DM GM | 112 | 100 | 3000 | D |
35 |
15A/1.5μs | |
BRP131 LED125/NW 100W 220-240V DM GM | 112 | 100 | 4000 | ||||
BRP131 LED125/CW 100W 220-240V DM GM | 112 | 100 | 5700 | ||||
BRP132 LED175/WW 140W 220-240V DM GM | 154 | 140 | 3000 | D |
25 |
15A/1.5μs | |
BRP132 LED175/NW 140W 220-240V DM GM | 154 | 140 | 4000 | ||||
BRP132 LED175/CW 140W 220-240V DM GM | 154 | 140 | 5700 |
This product contains a light source of energy efficiency class: see table
Type | Weight(kg) | L×W×H(mm) | Wind force area(m²) |
BRP130 | 2.6 | 382.5×248.4×85 | 0.08 |
BRP131 | 3.2 | 453.8×277.2×85 | 0.11 |
BRP132 | 4 | 508.2×325.5×85 | 0.14 |
- Connect the power cord
- Pole mounting
- Anti-drop stainless steel rope and locknut for luminaire
- Surge production device (SPD) replacement
Warning
- The luminaire shall be installed by a qualified electrician and wired in accordance with the latest IEEE electrical regulations or the national requirements.
- Turn the power off before inspection, installation, or removal.
- If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similarly qualified person in order to avoid a hazard.
- Use IP66 rated environmentally sealed power connector with a cable clamp to ensure IP66 ingress protection
- Ensure power supply cables (L-N / L-N-E) are connected correctly before switching on.
- The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similarly qualified person.
Maintenance
- Ensure the power supply is switched off before attempting any maintenance work.
- Periodic cleaning of the luminaire optical lens cover will ensure maximum optical efficiency.
- Luminaire optical lens cover shall be cleaned with clean water and non-abrasive soap, cleaner or detergent solution.
Caution
The Luminaire must be used within the applicable product specifications, installation instructions and environmental conditions for storage & operations according to application guidelines provided by Signify for the product Warranty to be valid.
Warning
- The luminaire shall be installed by a qualified electrician and wired in accordance with the latest IEEE electrical regulations or the national requirements.
- Turn the power off before inspection, installation or removal.
- Refer to the technical datasheet for additional electrical properties to ensure safe installation.
- Luminaire installed must not be in contact with combustible materials.
- Ensure power supply cables (L-N/L-N-E) are connected correctly before switching on.
- The luminaire should be positioned so that prolonged staring into the luminaire at a distance closer than 3 m is not expected
- Do not stare at the operating light source.
- The light source and/or control gear and/or the external flexible cable contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similarly qualified person.
Maintenance
- Ensure the power supply is switched off before attempting any maintenance work.
- Periodic cleaning of the luminaire optical lens cover will ensure maximum optical efficiency.
- Luminaire optical lens cover shall be cleaned with clean water and non-abrasive soap, cleaner or detergent solution.
Caution
The Luminaire must be used within the applicable product specifications installation instructions and environmental conditions for storage & operations according to application guidelines provided by Signify for the product Warranty to be valid.