Asus ET12 AXE11000 Tri Band Router User Guide

ET12 AXE11000 Tri-Band Router
User Guide

Hardware Explanations

1. Plug the adapter into the DCIN port, and press the power switch.
2. The power LED will light up when your hardware is ready.

Button and Port Explanations

• 2.5G / iG WAN port
  Connect your optical modem to this port with a network cable.
• LAN ports 1-2
  Connect your PC to a LAN port with a network cable.
• 2.5G / 1G LAN port
  Connect your PC to a 2.5G / 1G LAN port with a network cable.

Specifications:

Before Setup

Preparing to set up an AiMesh WiFi system

1. Find two ZenWiFi Pro ET12. and power both on.
2. Use a network cable to connect your optical modem to the WAN port of either ZenWiFi Pro ET12. This ZenWiFi Pro ET12 will be the AiMesh router, and the other ZenWiFi Pro ET12 will be the AiMesh node.
3. The LEDs turn solid blue to indicate that ZenWiFi Pro ET12 is ready for setup.

ASUS Router App

Download the free ASUS Router APP to set up and manage your router(s).

AiMesh Setup Steps

1. Prepare
   Place your AiMesh router and node within 3 meters of each other during the setup process.
   
2. AiMesh node
   Keep your AiMesh node powered on and on standby for AiMesh system settings.
3. Enabling Bluetooth
4. Launching ASUS Router APP
   Enable Bluetooth on your phone. Launch ASUS Router APP, and then follow the on-screen in-structions to finish the AiMesh setup.

Troubleshooting

If your AiMesh router cannot find any AiMesh node nearby or synchronization fails, please check the following and try again.
a. Move your AiMesh node closer to the AiMesh router ideally. Ensure that it is within 3 meters.
b. Your AiMesh node is powered on.

THE BEST PERFORMANCE

Relocation
Locate the AiMesh router and node at the best place.

NOTES: To minimize interference, keep the routers away from devices like cordless phones. Bluetooth devices and microwave ovens.
We recommend that you place the routers in an open or spacious location.
ZenWiFi Pro ET12 LED indications
Solid white: Good signal
Solid yellow: Weak signal
Solid red: No signal

FREQUENTLY ASKED  QUESTIONS

FAQ
Q1: Does the AiMesh router support Access Point mode?
A: Yes. You can choose to set the AiMesh router as router mode or access point mode. Please go to web GUI (http://router.asus.com). and go to the page Administration > Operation Mode.  Q2: Could I set up a wired connection between AiMesh routers (Ethernet backhaul)?
A: Yes. The AiMesh system supports both wireless and wired connections between the AiMesh router and node to maximize throughput and stability. AiMesh analyzes the wireless signal strength for each frequency band available. and then determines automatically whether a wireless or wired connection is best to serve as the inter-router connection backbone.

1. Follow the setup steps to establish a connection between the AiMesh router and node via WiFi first.
2. Place the node in the ideal locations for the best coverage. Run an Ethernet cable from the LAN port of the AiMesh router to the WAN port of the AiMesh node.
3. AiMesh system will auto-select the best path for data transmission, whether wired or wireless.

ASUS Recycling/Takeback Services
ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment We believe in providing solutions for you to be able to responsibly recycle our products, batteries, other components, as well as the packaging materials. Please go to http://csr.asus.com/english/Takeback.htm for detailed recycling information in different regions.
REACH
Complying with the REACH (Registration, Evaluation, Authorisation, and Restriction of Chemicals) regulatory framework, we published the chemical substances in our products on the ASUS REACH website at http://csr.asus.com/english/REACH.htm
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause undesired operation.

FCC regulations restrict the operation of this device to indoor use only.
This device cannot operate as a subordinate between separate buildings or structures.
The operation of this device is prohibited on oil platforms, cars, trains, boats, and aircraft, except that operation of this device is permitted in large aircraft while flying above 10,000 feet.
Operation of transmitters in the 5.925-7.125 GHz band is prohibited for control of or Communications with unmanned aircraft systems.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

WARNING: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Prohibition of Co-location
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.
IMPORTANT NOTE:
Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End-users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC exposure compliance requirements, please follow operation instructions as documented in this manual.
WARNING! This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 26 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
Safety Notices

• Use this product in environments with ambient temperatures between 0°C(32°F) and 40°C(104°F).
• Refer to the rating label on the bottom of your product and ensure your power adapter complies with this rating.
• DO NOT place on uneven or unstable work surfaces. Seek to service if the casing has been damaged.
• DO NOT place or drop objects on top and do not shove any foreign objects into the product.
• DO NOT expose to or use near liquids, rain, or moisture. DO NOT use the modem during electrical storms.
• DO NOT cover the vents on the product to prevent the system from getting overheated.
• DO NOT use damaged power cords, accessories, or other peripherals.
• If the Adapter is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer.
• To prevent electrical shock hazards, disconnect the power cable from the electrical outlet before relocating the system.

Compliance Statement of Innovation, Science and Economic Development Canada (ISED)
This device complies with Innovation, Science, and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. CAN ICES-003(B)/NMB-0O3(B)
Radio Frequency (RF) Exposure Information
The radiated output power of the ASUS Wireless Device is below the Innovation, Science, and Economic Development Canada radio frequency exposure limits. The ASUS Wireless Device should be used in such a manner that the potential for human contact during normal operation is minimized. This equipment should be installed and operated with a minimum distance of 26 cm between the radiator and any part of your body.
This device has been certified for use in Canada. The status of the listing in the Innovation, Science and Economic Development Canada’s REL (Radio Equipment List) can be found at the following web address: http://www.ic.gc.ca./eic/site/ceb-bhst.nsf/eng/htt00020.html
Additional Canadian information on RF exposure also can be found on the following web: http://www.ic.gc.ca./eic/site/smt-gst.nsf/sf08792.html

FAST Networking Solutions
FARTHEST-ESYE-SECURE-TRUSTED