LGSBWAC95 RF Module User Manual

LGSBWAC95 RF Module

Features

LGSBWAC95 is a small size and low-power module for IEEE 802.11ac wireless LAN & BT5.0 + HS. ETWCFMBC01 is based on the Mediatek MT7668AUN solution.

  • IEEE 802.11 a/b/g/n/ac Dual Band Dual Concurrent (DBDC)
  • Bluetooth 5.0+ HS , BLE
  • Size : 68 x 30 x 6.65mm
  • Two stream spatial multiplexing up to 300Mbps(802.11n) / 867Mbps(802.11ac)
  • Use on-chip OTP (One-Time Programmable)
  • Host Interface : USB2.0 (WLAN & BT)

This model is using the common USB2.0 to control WLAN and BT

  • Security : WAPI, WEP, WPA, WPA2, WMM, AES, TKIP, CKP
  • Application: DTV, DVR, HD DVD Player, Blue-ray Disk Player, STB

Picture of Product

Installation Manual

Install the module like below in the back of the TV

Block Diagram

Absolute Maximum Ratings

Caution: The specifications in Table 1 define levels at which permanent damage to the device can occur. Function operation is not guaranteed under these conditions. Operating at absolute maximum conditions for extended periods can adversely affect the long-term reliability of the device.

Other conditions

  1. Do not use or store modules in the corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt, or the like are contained. Also, avoid exposure to moisture.
  2. Store the modules where the temperature and relative humidity do not exceed 5 to 40℃ and 20 to 60%.
  3. Assemble the modules within 6 months. Check the soldering ability in case of 6 months over.

Operating Conditions

Standard Test Conditions

The Test for electrical specification shall be performed under the following condition Otherwise the following conditions, are not guaranteed this performance.

Ambient condition

Power supply voltages

Pin Description

Outline Drawing

Packing Information

<Regulatory notice>

FCC Statement

FCC Part 15.19 Statements:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Part 15.105 statement (Class B)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

FCC Part 15.21 statement
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
Responsible Party Information
Supplier’s Declaration of Conformity 47 CFR § 2.1077 Compliance Information
Responsible Party – U.S. Contact Information

  • LG Electronics USA
  • 1000 Sylvan Avenue Englewood Cliffs
  • New Jersey, United States, 07632
  • Telephone number or internet contact information

Regulatory notice to host manufacturer according to KDB 996369 D03 OEM Manual v01>
List of applicable FCC rules
This module has been granted modular approval as below listed FCC rule parts. FCC Rule parts 15C(15.247)
Summarize the specific operational use conditions
The OEM integrator should use equivalent antennas which is the same type and equal or less gain then an antenna listed in 2.7 in this instruction manual.
RF exposure considerations

  • The module has been certified for integration into products only by OEM integrators under the following condition:
  • The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is maintained between the radiator (antenna) and all persons at all times.
  • The transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures.
  • Mobile use
  • As long as the three conditions above are met, further transmitter testing will not be required. OEM integrators should provide the minimum separation distance to end users in their end-product manuals.

Antennas list

This module is certified with the following integrated antenna.

  • Type: Metal antenna (Internal Antenna)
  • Max. peak Antenna gain

Any new antenna type, higher gain than listed antenna should be met the requirements of FCC rule 15.203 and 2.1043 as permissive change procedure.]

Label and compliance information End Product Labeling

The module is labeled with its own FCC ID and IC Certification Number. If the FCC ID and IC Certification Number are not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case, the final end product must be labeled in a visible area with the following: “Contains FCC ID: BEJLGSBWAC95” “Contains IC: 2703H-LGSBWAC95”
Information on test modes and additional testing requirements
OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, the additional transmitter in the host, etc.).
Additional testing, Part 15 Subpart B disclaimer
The final host product also requires Part 15 subpart B compliance testing with the modular transmitter installed to be properly authorized for operation as a Part 15 digital device.

ISED
RSS-GEN, Sec. 7.1.3– (license-exempt radio apparatus)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: 2. ISED RSS-GEN, Sec. 7.1.3– (license-exempt radio apparatus) This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

  1. this device may not cause interference, and
  2. this device must accept any interference, including interference that may cause undesired operation of the device.

RF Exposure
The antenna (or antennas) must be installed so as to maintain at all times a distance minimum of at least 20 cm between the radiation source (antenna) and any individual. This device may not be installed or used in conjunction with any other antenna or transmitter.
l’exposition aux RF
L’antenne (ou les antennes) doit être installée de façon à maintenir à tout instant une distance minimum de au moins 20 cm entre la source de radiation (l’antenne) et toute personne physique.
Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment. Attention:
Les changements ou modifications de cet appareil non expressément approuvé par le fabricant peuvent annuler votre droit à utiliser cet équipement.
3. CE
Simplified EU Declaration of Conformity
Hereby, LG Electronics Inc. declares that the radio equipment type RF Module is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.lg.com/global/support/cedoc/cedoc#
RF Exposure
The antenna (or antennas) must be installed so as to maintain at all times a distance minimum of at least 20 cm between the radiation source (antenna) and any individual. This device may not be installed or used in conjunction with any other antenna or transmitter The use of the 5150 – 5350 MHz band is restricted to indoor use only. This restriction will be applied in all member states. Manufacturer name: LG Electronics Inc. The postal address: LG Electronics European Shared Service Center B.V. Krijgsman 1, 1186 DM Amstelveen, The Netherlands The host manufacturer has the responsibility that the host device should be compliant with all essential requirements of RED.