Sharp SJ-BA34CHXIE-EU Upright Standing Fridge-Freezers User Manual
Home Appliances
SJ-BA34CHXIE-EU
Fridge-freezers
User Manual
Your fridge freezer conforms to current safety requirements. Inappropriate use can lead to personal injury and damage to property. To avoid the risk of damage, read this manual carefully before using your fridge freezer for the first time.
It contains important safety information on the installation, safety, use, and maintenance of your fridge freezer. Retain this manual for future use.
CHAPTER -1: GENERAL WARNINGS
- While carrying and positioning the fridge, do not damage the cooler gas circuit.
- Do not store any containers with flammable materials, such as spray cans or fire extinguisher refill cartridges in the vicinity of the fridge.
- This appliance is intended to be used in household and similar applications such as;
– staff kitchen areas in shops, offices, and other working environments that can be equated with ordinary household
– farm houses and by clients in hotels, motels, and other residential type environments which can be equated with ordinary household
– bed and breakfast type environments which can be equated with ordinary household
– catering and similar non-retail applications which can be equated with ordinary household - Your fridge requires a 220-240V, 50Hz mains supply. Do not use any other supply. Before connecting your fridge, ensure that the information on the data plate (voltage and connected load) matches the mains electricity supply. If in doubt, consult a qualified electrician)
- This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazard involved. Children shall not play with the appliance. Cleaning and user maintenance, shall not be made by children without supervision.
- Children aged from 3 to 8 years are allowed to load and unload refrigerating appliances. Children are not expected to perform cleaning or user maintenance of the appliance, very young children (0-3 years old) are not expected to use appliances, and young children (3-8 years old) are not expected to use appliances safely unless continuous supervision is given, older children (8-14 years old) and vulnerable people can use appliances safely after they have been given appropriate supervision or instruction concerning use of the appliance. Very vulnerable people are not expected to use appliances safely unless continuous supervision is given.
- A damaged power cord /plug can cause fire or give you an electric shock. When damaged it must be replaced, this should only be done by qualified personnel.
- This appliance is not intended for use at altitudes exceeding 2000 m.
To avoid contamination of food, please respect the following instructions: - Opening the door for long periods can cause a significant increase in the temperature in the compartments of the appliance.
- Clean regular surfaces that can come in contact with food and accessible drainage systems.
- Store raw meat and fish in suitable containers in the refrigerator, so that it is not in contact with or drip onto other food.
- Two-star frozen-food compartments are suitable for storing pre-frozen food, storing or making ice cream, and making ice cubes.
- One-, two- and three-star compartments are not suitable for the freezing of fresh food.
- If the refrigerating appliance is left empty for long periods, switch off, defrost, clean, dry, and leave the door open to prevent mold from developing within the appliance.
Disposal
- All packaging and materials used are environmentally friendly and recyclable. Please dispose of any packaging in an environmentally friendly manner. Consult your local council for further details.
- When the appliance is ready to be scrapped, cut off the electrical supply cable and destroy the plug and cable.
Disable the door catch in order to prevent children from getting trapped inside. - A cut-off plug inserted into a 16 amp socket is a serious safety (shock) hazard. Please ensure the cut-off plug is disposed of safely.
For Denmark products:
The appliance is equipped with a plug approved in the EU ( EU-Schuko Plug) and can be used in Finland, Norway, and Sweden. In Denmark, the appliance is only approved for use with a wall outlet type E or type CEE7 // 7-S with a ground leg. If there is only wall outlet type K at the connection point, Replacing the EU-Schuko plug with the Danish plug must be performed by only authorized service personnel. Alternatively, connect a suitable and approved power adapter to transition between the Schuko plug and the Danish earth system. This adapter (min. 10 amps and up to max. 13 amps) can be ordered via a well-assorted white goods dealer or authorized electrician. Only with one of these methods, it can be ensured that the appliance is on the correct safety ground. In the absence of earthing installation, an authorized electrician should carry out an earthing installation. In the case of use without earthing installed, we will not be responsible for any loss of use that may occur.
Disposal of your old appliance
Instead, it should be taken to applicable waste collection sites that recycle electrical and electronic equipment.
Recycling materials will help preserve our natural resources. For more detailed information regarding recycling this product, please contact your local authority, domestic waste disposal service, or the shop where you purchased the product.
Please ask your local authority about the disposal of WEEE for reuse, recycling, and recovery purposes.
Notes:
- Please read the instruction manual carefully before installing and using your appliance. We are not responsible for damage resulting from misuse.
- Follow all instructions for your appliance, and keep this manual handy in order to resolve any problems that may occur in the future.
- This appliance is produced to be used in homes and can only be used in domestic environments and for specified purposes. It is not suitable for commercial use. Such use will nullify the warranty and our company will not be responsible for any losses that occur.
- This appliance is produced for home use and it is only suitable for cooling / storing foods. It is not suitable for commercial uses and/or for storing any substances except for food. Our company is not responsible for any losses due to improper use.
Safety warnings
- Do not use a plug adapter.
- A damaged power cord/plug can cause fire or give you an electric shock. When damaged it must be replaced, this should only be done by qualified personnel.
- Never bend the power cord excessively.
- Never touch the power cord/plug with wet hands as this could cause a short circuit electric shock.
- Do not place glass bottles or beverage cans in the freezer department. Bottles or cans may explode.
- When taking ice made in the freezer department, do not touch it, ice may cause ice burns and/or cuts.
- Do not remove items from the freezer if your hands are damp or wet. This could cause skin abrasions or frost/freezer burns.
- Do not refreeze food once it has thawed out.
Installation Information
Before unpacking and maneuvering your fridge freezer please take some time to familiarise yourself with the following points.
- Position your fridge freezer out of direct sunlight and away from any heat source such as a radiator.
- Your appliance should be at least 50 cm away from stoves, gas ovens, and heater cores, and should be at least 5 cm away from electrical ovens.
- Do not expose your fridge freezer to moisture or rain.
- Your fridge freezer should be positioned at least 20mm away from another freezer.
- Clearance of at least 150 mm is required at the top of your appliance. Do not place anything on top of your appliance.
- For safe operation, it is important that your fridge freezer is seated securely and balanced. The adjustable feet are used to level your fridge freezer. Make sure that your appliance is level before placing any foodstuffs inside it.
- We recommend that you wipe all shelving and trays with a cloth soaked in warm water mixed with a teaspoon of bicarbonate of soda before use. After cleaning, rinse with warm water and dry.
If your refrigerator has a fan condenser:
The condenser of your fridge is placed at the bottom of the cabinet. As a result of that, assemble the spacer by fixing it to holes on the cover bottom panel and turn 90° that’s shown below the figure for arranging the distance between the refrigera¬tor and the back wall where you place the fridge. You can move the fridge towards the back wall until
that point.
The fridge freezer should be placed against a wall with a free distance not exceeding 75 mm.
Before using your fridge freezer
- Before setting up your fridge freezer, check for any visible damage. Do not install or use your fridge freezer if it is damaged
- When using your fridge freezer for the first time, keep it in an upright position for at least 3 hours before plugging it into the mains. This will allow efficient operation and prevent damage to the compressor.
- You may notice a slight odor when using your fridge freezer for the first time. This is perfectly normal and will fade away as the fridge starts to cool.
Information about new-generation cooling technology
Fridge freezers with new-generation cooling technology have a different working system than static fridge freezers. In normal fridge freezers, humid air enters the freezer and the water vapor emanating from the foods turns into frost in the freezer compartment. In order to melt this frost, in other words, defrost, the fridge has to be unplugged. In order to keep foods cold during the defrosting period, the user must store the food elsewhere and the user must clear the remaining ice and accumulated frost.
The situation is completely different in freezer compartments equipped with new-generation cooling technology. With the aid of a fan, cold and dry air is blown throughout the freezer compartment. As a result of the cold air that is blown easily throughout the compartment – even in the spaces between shelves – foods are frozen equally and properly. And there will be no frost.
The configuration in the refrigerator compartment will be nearly the same as the freezer compartment.
The air emitted by the fan located at the top of the refrigerator compartment is cooled while passing through the gap behind the air duct. At the same time, the air is blown out through the holes in the air duct so that the cooling process is successfully completed in the refrigerator compartment. Holes on the air duct are designed for even air distribution throughout the compartment.
Since no air passes between the freezer and refrigerator compartment, odors will not mix.
As a result, your fridge with new-generation cooling technology is easy to use and it offers you access to a huge volume and aesthetic appearance.
CHAPTER -2: YOUR FRIDGE FREEZER
This appliance is not intended to be used as a built-in appliance.
This figure has been drawn for information purposes to show the various parts and accessories in the appliance.
Parts may vary according to the model of the appliance.
General notes:
Fresh Food Compartment (Fridge): Most efficient use of energy is ensured in the configuration with the drawers in the bottom part of the appliance, and shelves evenly distributed, the position of door bins does not affect energy consumption.
Freezer Compartment (Freezer): Most Efficient use of energy is ensured in the configuration with the drawers and bins are on stock position.
CHAPTER -3: USING YOUR FRIDGE FREEZER
Display and Control Panel
Using the Control Panel
| 1. Freezer temperature setting. 2. Super Freeze mode indicator 3. Fridge temperature setting 4. Super Cooling mode indicator 5. Holiday mode indicator 6. Eco mode indicator |
7. Alarm indicator 8. Child Lock mode indicator 9. Screen selector 10. Decrease value 11. Increase value 12. Mode Selector 13. Child Lock Selector |
Operating your Fridge Freezer
Lighting (If available)
When the product is plugged in for the first time, the interior lights may turn on 1 minute late due to opening tests.
Super Freeze Mode
Purpose
- To freeze a large quantity of food that cannot fit on the fast freeze shelf.
- To freeze prepared foods.
- To freeze fresh food quickly to retain freshness.
- Press
- Once the Freezer temperature setting is selected, the temperature will flash.
- Press the
- Once the Super Freeze mode has been set, the machine will beep to confirm the mode has been switched on.
- After the beep, the original temperature of the freezer will appear on the screen.
- The mode can be canceled by repeating the above instructions from the beginning.
During this mode:
- The temperature of the fridge compartment may be adjusted, this will not impact Super Freeze Mode.
- Economy and holiday mode cannot be selected whilst Super Freeze is active.
Super Cool Mode
Purpose
- To cool and store a large quantity of food in the fridge compartment.
- To quickly cool drinks.
How to use
- Press
- Once the fridge temperature setting is selected, the temperature will flash.
- Press the
- Once the Super Cool mode has been set, the machine will beep to confirm the mode has been switched on.
- After the beep, the last temperature of the fridge will appear on the screen.
- The mode can be canceled by repeating the above instructions from the beginning.
During this mode:
- The temperature of the freezer compartment may be adjusted, this will not impact Super Cool Mode.
- Economy and holiday mode cannot be selected whilst Super Cool is active.
Economy Mode
Purpose
Energy savings. During periods of less frequent use (door opening) or absence from home, such as a holiday, the Eco program can provide optimum temperature whilst saving power.
How to Use
- Press
- Once the ‘Eco mode’ has been set, the machine will beep
to confirm the mode has been switched on. - After the beep, both the fridge and freezer temperature settings (#1 and #3) will display an ‘E’.
- Eco Mode can be canceled by pressing the
During this mode:
- The freezer and fridge temperature may be adjusted however the adjustment will not be made until Eco Mode is canceled. When the economy mode is canceled, the selected setting values will be activated and the temperature(s) will be adjusted.
- Super Cool or Super Freeze mode can be selected, however, by selecting either mode Eco Mode is canceled immediately.
- Holiday mode can only be selected after canceling the economy mode.
Holiday Mode
Purpose
Holiday mode is to be used if the device is to be left for an extended period. During Holiday mode only the freezer compartment remains active.
- Press
- Once the ‘Holiday mode’ has been set, the machine will beep to confirm the mode has been switched on.
- After the beep the fridge will display ‘–’ and the freezer will display the -18 o C set temperature.
- Holiday Mode can be canceled by pressing the
During this mode:
- Freezer and fridge temperature may be adjusted however the adjustment will not be made until Holiday Mode is canceled. When Holiday mode is canceled, the selected setting values will be activated and the temperature(s) will be adjusted.
- Super Cool or Super Freeze mode can be selected, however, by selecting either mode Holiday Mode is canceled immediately.
- Eco Mode can only be selected after the Holiday mode has been canceled.
Drink Cool Mode
Purpose
This mode is used to cool drinks within an adjustable time frame.
- Press
- The cooler temperature set indicator will start showing ‘05’. This value will flash on the screen
- Users can either press
- When you select the time the numbers will blink 3 times on screen and sound beep beep. If the user does not press any button within 2 seconds the time will be set.
- The machine will then set the time, and the remaining time will be shown on the screen
- Once the total time has elapsed, an alarm will sound
- Cool Drink Mode can be canceled by following pressing the
During this mode:
- When drink cool and child lock modes are active, the child lock mode must be canceled in order to stop the alarm sound
- While using this mode, you must regularly check the temperature of the bottles. When the bottles are cool enough, you must take them out of the appliance.
- Bottles can explode if left in the appliance for too long with drink cool mode active.
Screen Saver Mode
Purpose
This mode saves energy by switching off all control panel lighting when the panel is left inactive.
How to Use
- Screen saver mode will be activated automatically after 30 seconds.
- If you press any key while the lighting of the control panel is off, the current machine settings will reappear on the display to let you make any change you wish.
- If you do not cancel the screen saving mode or press any key for 30 seconds, the control panel will remain off.
To deactivate the screen saving mode,
- To cancel the screen saving mode, first of all, you need to press any key to activate the keys and then press and hold the Mode button ”
- To reactivate screen saving mode, press and hold the mode button “
The Child Lock Function
Purpose
Child lock can be activated to prevent any accidental or unintentional changes from being made to the appliance settings.
Press and hold the child lock button
Canceling Child Lock
Press and child lock button
Door Open Alarm Function
If either the fridge or freezer door is left open for more than 2 minutes, the appliance will beep.
Temperature Settings
Freezer Temperature Settings
- Press
- Once the Freezer temperature setting is selected, the temperature will flash.
- Users can then use the up or down arrow (
- If Super Freeze mode or Eco mode is activated, the temperature will not change until the mode is canceled.
Cooler Temperature Settings
- Press
- Once the Fridge temperature setting is selected, the temperature will flash.
- Users can then use the up or down arrow (
- If Super Freeze mode or Eco mode is activated, the temperature will not change until the mode is canceled.
Warnings About Temperature Adjustments
- It is not recommended that you operate your fridge in environments colder than 10°C.
- Temperature adjustments should be made according to the frequency of door openings, the quantity of food kept inside the fridge, and the ambient temperature of the placement of your fridge.
- Your fridge should be operated for up to 24 hours according to the ambient temperature without interruption after being plugged in, this is so it is completely cooled. Do not open the doors of your fridge and do not place food inside it during this period.
- A 5-minute delay function is applied to prevent damage to the compressor of your fridge when you take the plug out and then plug it back in again after an energy breakdown has occurred. Your fridge will start to operate normally after 5 minutes.
- Your fridge is designed to operate in the ambient temperature intervals stated in the standards, according to the climate class stated in the information label. We do not recommend operating your fridge out of the stated temperature value limits in terms of cooling effectiveness.
- This appliance is designed for use at an ambient temperature within the 10°C – 43°C range.
Climate class and meaning:
T (tropical): This refrigerating appliance is intended to be used at ambient temperatures ranging from 16 °C to 43 °C.
ST (subtropical): This refrigerating appliance is intended to be used at ambient temperatures ranging from 16 °C to 38 °C.
N (temperate): This refrigerating appliance is intended to be used at ambient temperatures ranging from 16 °C to 32 °C.
SN (extended temperate): This refrigerating appliance is intended to be used at ambient temperatures ranging from 10 °C to 32 °C.
Temperature indicator
In order to help you better set your refrigerator, we have equipped it with a temperature indicator located in the coldest area.
Since “OK” appears in black, it will be difficult to see this indication if the temperature indicator is badly lit. To be able to see this indication properly, there should be enough light.
Each time the temperature setting device is changed, wait for the stabilization of the temperature inside the appliance before proceeding, if necessary, with a new temperature setting. Please change the position of the temperature setting device progressively and wait at least 12 hours before starting a new check and potential change.
NOTE: Following repeated openings (or prolonged opening) of the door or after putting fresh food into the appliance, it is normal for the indication “OK” not to appear in the temperature setting indicator. If there is an abnormal ice crystals build-up (bottom wall of the appliance) on the refrigerator compartment evaporator (overloaded appliance, high room temperature, frequent door openings), set the temperature setting device to a lower position until compressor off periods are obtained again.
Putting food in the coldest area of the refrigerator
The following symbol indicates the coldest area of your refrigerator.
To ensure a low temperature in this area, make sure the shelf is located at the same level as this symbol, as shown in the illustration.
The upper limit of the coldest area is indicated by the lower side of the sticker (head of the arrow). The coldest area upper shelf must be at the same level as the arrowhead.
The coldest area is below this level.
As these shelves are removable, make sure they are always at the same level with these zone limits described on the stickers, in order to guarantee temperatures in this area.
Accessories
Icematic (In some models)
- Take out the ice-making tray
- Fill the water in the line.
- Place the ice-making tray in its original position
- When ice cubes are formed, twist the lever to drop ice cubes into the icebox.
Note:
- Do not fill the icebox with water in order to make ice. It may be broken.
- The movement of the ice maker may be difficult while the refrigerator is running. In such a case, it should be cleaned after removing the glass shelves.
Ice tray (In some models)
- Fill the ice tray with water and place it in the freezer compartment.
- After the water is completely turned into ice, you can twist the tray as shown below to get the ice cube.
Keeping food in instead of the freezer or refrigerator compartment allows food to retain freshness and flavor longer while preserving its fresh appearance. If the chiller tray becomes dirty, remove it and wash it with water.
(Water freezes at 0 °C, but foods containing salt or sugar require lowered temperatures to freeze)
Normally people use the chiller compartment for raw fish, rice, etc… Do not put foods you want to freeze or ice trays in order to make ice.
- Pull the chiller shelf out toward you by sliding it on rails.
- Pull the chiller shelf up from the rail to remove it.
Freezer box
- The freezer box is for foods that need to be accessed more easily.
- Removing The freezer box;
- Pull the box out as far as possible
- Pull the front of the box up and out.
! Make the inverse of the same operation for resetting the sliding compartment.
Note: Always hold the handle of the box while moving in or out.
Fresh dial
If you want to keep your vegetables longer in that compartment, you have to change the humidity controller that is located at the front of the crisper, to the closed position. With the aid of this function, the humidity level in the crisper compartment will stay constant and vegetables will last longer.
If you want to keep your vegetables colder in that compartment, you have to change the humidity controller to an open position. By doing this change, you will allow the cold air to enter the crisper compartment. As a result of this, your vegetables will be colder.
If you see any condensation on the glass shelf that is located at the top of the crisper, you can change the humidity controller to an open position.
Adaptive-Lift Door Shelf (In some models)
Six different height adjustments can be made to provide storage areas that you need by Adapti-Lift.
To change the position of Adapti-Lift ;
Hold the bottom of the shelf and pull the buttons on the side of the door shelf direction of the arrow (Fig.1)
Position the door shelf at the height you need by moving up and down.
After you get the position that you want the door shelf, release the buttons on the side of the door shelf (Fig.2) Before releasing the door shelf, move up down and make sure the door shelf is fixed
Note: Before moving the door shelf is loaded, you must hold the shelf by supporting the bottom. Otherwise, the door shelf could fall off the rails due to the weight. So damage may occur on the door shelf or rails.
Visual and text descriptions on the accessories section may vary according to the model.
- Make sure to unplug the fridge before starting to clean it.
- Do not wash your fridge by pouring water.
- You can wipe the inner and outer sides with a soft cloth or a sponge using warm and soapy water.
- Remove the parts individually and clean with soapy water. Do not wash in the dishwasher.
- Never use flammable, explosive, or corrosive material like thinner, gas, or acid for cleaning.
- You should clean the condenser with a broom at least once a year in order to provide energy-saving and increase productivity.
Make sure that your fridge is unplugged while cleaning.
Replacing The LED (if an LED is used as lighting)
Please contact the Sharp help desk as this should be changed by authorized personnel only.
Note: Numbers and location of LED strips may change according to different models.
CHAPTER -4: FOOD STORAGE GUIDANCE
Refrigerator compartment
• To reduce frost build-up never place liquids with unsealed containers in the fridge compartment.
• Allow warn or hot food to cool down before storing. This helps reduce power consumption.
• To avoid frost build-up ensure that nothing is stored touching the back wall.
• The coldest area of the refrigerator is at the bottom. We recommend using this area to store food that will perish easily, such as fish, ready meals, baked goods, or dairy products. The warmest area is the top shelf of the door. We recommend you store butter or cheese here.
Important Note:
• Cover any finished dishes when you put them in the fridge. Place them in the fridge when they are cool, otherwise, the temperature/ humidity inside the fridge increases, and this causes the fridge to operate more. Covering food and beverages also preserves their flavor and aroma.
• Potatoes, onion, and garlic shouldn’t be kept in the fridge.
• Please avoid the foods from touching a temperature sensor that is located in the refrigerator compartment. In order to keep optimum preservation temperature in the refrigerator compartment, foods mustn’t contact with the sensor.
Freezer compartment
- Use the freezer to store frozen foods for long periods of time and make ice cubes.
- To freeze fresh food – ensure that as much of the surface of the food to be frozen is in contact with the cooling surface.
- Do not put fresh food on either side of frozen food as it can thaw it.
- While freezing fresh foods(i.e meat, fish, and mincemeat), divide into portion sizes.
- Once the unit has been defrosted replace the foods in the freezer and remember to consume them in a short period of time.
- Never place warm food in the freezer compartment.
- The instructions shown on frozen food packages should always be followed carefully and if no information is provided food should not be stored for more than 3 months from the purchased date.
- When buying frozen foods ensure that these have been frozen at suitable temperatures and that the packing is intact.
- Frozen foods should be transported in appropriate containers to maintain the quality of the food and should be stored in the freezer as soon as possible.
- If a package of frozen food shows signs of humidity and abnormal swelling it has been previously stored at an unsuitable temperature and the contents have deteriorated.
- The storage life of frozen foods depends on the room temperature, thermostat setting, how often the door is opened, the type of food, and the length of time required to transport the product from the shop to your home.
Always follow the instructions printed on the package and never exceed the maximum storage life indicated.
That; If you decide to open the freezer door again immediately after closing, it may be difficult to re-open. This is normal
and after the freezer has reached an equilibrium condition the door will open easily.
Important note:
- Frozen foods, when thawed, should be cooked just like fresh foods. If they are not cooked after being thawed they must NEVER be re-frozen.
- The taste of some spices found in cooked dishes (anise, basilica, watercress, vinegar, assorted spices, ginger, garlic, onion, mustard, thyme, marjoram, black pepper, etc.) changes, and they assume a strong taste when they are stored for a long period. Therefore, only add a small amount of spice if planning to freeze, or the desired spice should be added after the food has been thawed.
- The storage period of food is dependent on the oil used. The suitable oils are margarine, calf fat, olive oil, and butter, and the unsuitable oils are peanut oil and pig fat.
- The food in liquid form should be frozen in plastic cups and the other food should be frozen in plastic folios or bags.
- For normal working conditions, it will be sufficient to adjust the temperature setting of your refrigerator to +4 °C.
- The temperature of the fridge compartment should be in the range of 0-8 °C, fresh foods below 0 °C are iced and rotted, bacterial load increases above 8 °C, and spoils.
- Do not put hot food in the refrigerator immediately, wait for the temperature to pass outside. Hot foods increase the degree of your refrigerator and cause food poisoning and unnecessary spoiling of the food.
- Meat, fish, etc. should be stored in the chiller compartment of the food, and the vegetable compartment is preferred for vegetables. (if available)
- To prevent cross-contamination, meat products, and fruit vegetables are not stored together.
- Foods should be placed in the refrigerator in closed containers or covered to prevent moisture and odors.
CHAPTER -5: DOOR REVERSAL
Repositioning the door
- It depends on which fridge freezer you have as to whether it is possible the reverse the doors.
- It is not possible where handles are attached to the front of the appliance.
- If your model does not have handles it is possible to reverse the doors, but this needs to be completed by authorized personnel. Please call Sharp service.
CHAPTER -6: TROUBLESHOOTING
Check Warnings;
Your fridge freezer warns you if the temperatures for the cooler and freezer are at improper levels or when a problem occurs in the appliance. Warning codes are displayed in the Freezer and Cooler Indicators.
| ERROR TYPE | MEANING | WHY | WHAT TO DO |
| E01 | Sensor warning | Contact the Sharp help desk as soon as possible. | |
| E02 | Sensor warning | Contact the Sharp help desk as soon as possible. | |
| E03 | Sensor warning | Contact the Sharp help desk as soon as possible. | |
| E06 | Sensor warning | Contact the Sharp help desk as soon as possible. | |
| E07 | Sensor warning | Contact the Sharp help desk as soon as possible. |
| E08 | Low Voltage Warning | Power supply to the device has dropped to below 170W. |
– This is not a device failure. this error helps to prevent damage to the compressor. – The voltage needs to be increased back to the required levels If this warning continues, contact the Sharp help desk as soon as possible. |
| E09 | Freezer compartment is not cold enough |
Likely to occur after long term power failure. |
1. Set the freezer temperature to a colder value or set Super Freeze. This should remove the error code once the required temperature has been reached. Keep doors closed to improve the time taken to reach the correct temperature. 2. Remove any products which have thawed/defrosted during this error. They can be used within a short period of time. 3. Do not add any fresh produce to the freezer compartment until the correct temperature has been reached and the error is no longer. If this warning continues, contact the Sharp help desk as soon as possible. |
| E10 | Fridge compartment is not cold enough |
Likely to occur atter: – Long-term power failure. – Hot food has been left in the fridge. |
1. Set the fridge temperature to a colder value or set Super Cool. This should remove the error code once the required temperature has been reached. Keep doors closed to improve the time taken to reach the correct temperature. 2. Please empty the location at the front area of air duct channel holes and avoid putting food close to the sensor. If this warning continues. contact the Sharp help desk as soon as possible. |
| E11 | Fridge compartment is too cold |
Various | 1. Check is Super Cool mode is activated 2. Reduce the fridge compartment temperature I Check to see if vents are clear and not clogged If this warning continues. contact the Sharp help desk as soon as possible. |
If your fridge is not operating;
- Is there a power failure?
- Is the plug connected to the socket correctly?
- Is the fuse of the socket to which the plug is connected or is the main fuse blown?
- Is there any failure at the socket? To check this, plug your refrigerator into a known working socket.
If your fridge is not cooling enough;
- Is the temperature adjustment right?
- Is the door of your fridge opened frequently and left open for a long while?
- Is the door of the fridge closed properly?
- Did you put a dish or food on your fridge so that it contacts the rear wall of your fridge so as to prevent air circulation?
- Is your fridge filled excessively?
- Is there adequate distance between your fridge and the rear and side walls?
- Is the ambient temperature within the range of values specified in the operating manual?
If the food in your refrigerator compartment is over cooled
- Is the temperature adjustment right?
- Is there much food recently put inside the freezer compartment? If so, your fridge may overcook the food inside the refrigerator compartment as it will operate longer to cool this food.
If your fridge is operating too loudly;
To maintain the set cooling level, the compressor may be activated from time to time. Noises from your fridge at this time are normal due to their function. When the required cooling level is reached, noises will be decreased automatically. If the noises persist;
- Is your appliance stable? Are the legs adjusted?
- Is there anything behind your fridge?
- Are the shelves or dishes on the shelves vibrating? Replace the shelves and/or dishes if this is the case.
- Are the items placed on your fridge vibrating?
Normal Noises;
Cracking (Ice cracking) Noise:
• During automatic defrosting.
• When the appliance is cooled or warmed (due to expansion of appliance material).
Short cracking: Heard when the thermostat switches the compressor on/off.
Compressor noise (Normal motor noise): This noise means that the compressor operates normally Compressor may cause more noise for a short time when it is activated.
Bubbling noise and splash: This noise is caused by the flow of the refrigerant in the tubes of the system.
Water flow noise: Normal flow noise of water flowing to the evaporation container during defrosting. This noise can be heard during defrosting.
Air Blowing Noise (Normal fan noise): This noise can be heard in the No-Frost fridge during the normal operation of the system due to the circulation of air.
If humidity builds up inside the fridge;
- Has the food been properly packaged? Have the containers been well dried before they were put into the refrigerator?
- Are the doors of the refrigerator opened very frequently? When the door is opened, the humidity found in the air in the room enters the refrigerator. Especially if the humidity rate in the room is too high, the more frequently the door is opened the faster will be the humidification.
If the doors are not opened and closed properly;
- Do the food packages prevent the closing of the door?
- Are the door compartments, shelves, and drawers placed properly?
- Are door gaskets broken or torn?
- Is your fridge on a level surface?
If the edges of fridge cabinet that the door joint contact are warm;
Especially in summer (hot weather), the surfaces that the joint contact may get warmer during the operation of the compressor, this is normal.
IMPORTANT NOTES:
- The compressor protection thermal fuse will cut out after sudden power breakdowns or after unplugging the appliance because the gas in the cooling system is not stabilized. This is quite normal, and the fridge will restart after 4 or 5 minutes.
- The cooling unit of your refrigerator is hidden in the rear wall. Therefore, water droplets or ice may occur on the rear surface of your fridge due to the operation of the compressor at specified intervals. This is normal. There is no need to perform a defrosting operation unless the ice is excessive.
- If you will not use your fridge for a long time (e.g. in the summer holidays) unplug it. Clean your fridge according to Part 4 and leave the door open to prevent humidity and smell.
- The appliance you have purchased is designed for home-type use and can be used only at home and for the stated purposes. It is not suitable for commercial or common use. If the consumer uses the appliance in a way that does not comply with these features, we emphasize that the producer and the dealer shall not be responsible for any repair and failure within the guarantee period.
- If the problem persists after you have followed all the instructions above, please consult an authorized service provider.
CHAPTER -7: TIPS FOR SAVING ENERGY
- Always allow foodstuffs to cool before storing them in the appliance.
- Thaw food in the fridge compartment, this helps save energy.
- The door gasket must be clean and pliable. In case of wear, if your gasket is detachable, replace the gasket. If not detachable, you have to replace the door.
CHAPTER -8: TECHNICAL DATA
The technical information is situated in the rating plate on the internal side of the appliance and on the energy label.
The QR code on the energy label supplied with the appliance provides a web link to the information related to the performance of the appliance in the EU EPREL database.
Keep the energy label for reference together with the user manual and all other documents provided with this appliance.
It is also possible to find the same information in EPREL using the link https://eprel.ec.europa.eu and the model name and product number that you find on the rating plate of the appliance.
See the link www.theenergy label.eu for detailed information about the energy label.
CHAPTER -9: CUSTOMER CARE AND SERVICE
Always use original spare parts.
When contacting our Authorised Service Centre, ensure that you have the following data available: Model, Serial Number, and Service Index.
The information can be found on the rating plate. You can find the rating label inside the fridge zone on the left lower side.
The original spare parts for some specific components are available for a minimum of 7 or 10 years, based on the type of component, from the placing on the market of the last unit of the model.
Visit our website to:
www.sharphomeappliances.com
Support
Visit Our Website
sharphomeappliances.com
52338669
