Whirlpool Top-Load Washer with Pretreat Station Instruction Manual
Whirlpool Top-Load Washer with Pretreat Station
OPERATING AND SAFETY INSTRUCTIONS
IMPORTANT TO BE READ AND OBSERVED:
Before using the appliance, read these safety instructions. Keep them nearby for future reference. These instructions and the appliance itself provide important safety warnings, to be observed at all times. The manufacturer declines any liability for failure to observe these safety instructions, for inappropriate use of the appliance or incorrect setting of controls.
Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed. |
IMPORTANT SAFETY INSTRUCTIONSWARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions, including the following:
SAVE THESE INSTRUCTIONS |
GROUNDING INSTRUCTIONSFor a grounded, cord-connected washer:
WARNING: Improper connection of the equipmentgrounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance – if it will not fit the outlet, have a proper outlet installed by a qualified electrician. |
INSTALLATION REQUIREMENTS
WARNING: To reduce the risk of fire, electric shock, or injury to persons, read the INSTALLATION & CARE INSTRUCTIONS GUIDE online, before installing this appliance.
Excessive Weight Hazard Use two or more people to move and install washer. Failure to do so can result in back or other injury. |
ELECTRICAL REQUIREMENTS
WASHER MAINTENANCE AND CARE
WATER INLET HOSES
Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Periodically inspect and replace inlet hoses if bulges, kinks, cuts, wear, or leaks are found. When replacing your inlet hoses, mark the date of replacement on the label with a permanent marker.
NOTE : Do not use old hoses. Property damage can result.
WASHER CARE
Recommendations to Help Keep Your Washer Clean and Performing at its Best:
- Always use High Efficiency (HE) detergents and follow the HE detergent manufacturer’s instructions regarding the amount of HE detergent to use. Never use more than the recommended amount because that may increase the rate at which detergent and soil residue accumulate inside your washer, which in turn may result in undesirable odor.
- Use warm and hot wash water settings sometimes (not exclusively cold water washes), because they do a better job of controlling the rate at which soils and detergent accumulate.
- Always leave the washer lid open between uses to help dry out the washer and prevent the buildup of odor-causing residue.
NON-USE AND VACATION CARE:
Operate your washer only when you are home. If moving, or not using your washer for a period of time, follow these steps:
- Unplug or disconnect power to the washer.
- Turn off the water supply to the washer, to avoid flooding due to water pressure surge.
WINTER STORAGE CARE
IMPORTANT: To avoid damage, install and store washer where it will not freeze. Because some water may stay in hoses, freezing can damage the washer. If storing or moving during freezing weather, winterize your washer.
To winterize washer:
- Shut off both water faucets; disconnect and drain water inlet hoses.
- Put 1 quart (1 L) of R/V/-type antifreeze into an empty basket.
- Unplug washer or disconnect power.
REINSTALLING/USING WASHER AGAIN
To reinstall washer after non-use, vacation, winter storage, or moving:
- See the “Installation & Care Instructions Guide” online for more information to locate, level, and connect the washer.
- Before using again, run washer through the following recommended procedure:
To use washer again:
- Flush water pipes and hoses. Reconnect water inlet hoses. Turn on both water faucets.
- Plug in washer or reconnect power.
- Run the washer through the BEDDING cycle to clean washer and remove antifreeze, if used. Use only HE (High Efficiency) detergent. Use 1/2 the manufacturer’s recommended amount for a medium-size load.
©2022. All rights reserved. Used under license in Canada.