KENWOOD Receiver User Manual

KENWOOD Receiver User Manual

CD-RECEIVER / DIGITAL MEDIA RECEIVER
Quick Start Guide
JVCKENWOOD Corporation

For detailed operations and information, refer to the INSTRUCTION MANUAL on the following website:
<www.kenwood.com/cs/ce/>

Information on Disposal of Old Electrical and Electronic Equipment and Batteries (applicable for countries that have adopted separate waste collection systems)

Products and batteries with the symbol (crossed-out wheeled bin) cannot be disposed as household waste.

Old electrical and electronic equipment and batteries should be recycled at a facility capable of handling these items and their waste byproducts.

Contact your local authority for details in locating a recycle facility nearest to you. Proper recycling and waste disposal will help conserve resources whilst preventing detrimental effects on our health and the environment.

Notice: The sign “Pb” below the symbol for batteries indicates that this battery contains lead.

The marking of products using lasers
The label is attached to the chassis/case and says that the component uses laser beams that have been classified as Class 1. It means that the unit is utilizing laser beams that are of a weaker class. There is no danger of hazardous radiation outside the unit.

Declaration of Conformity with regard to the RE Directive 2014/53/EU
Declaration of Conformity with regard to the RoHS Directive 2011/65/EU

Manufacturer:
JVCKENWOOD Corporation
3-12, Moriya-cho, Kanagawa-ku, Yokohama-shi, Kanagawa, 221-0022, JAPAN

EU Representative:
JVCKENWOOD Europe B.V.
Amsterdamseweg 37, 1422 AC UITHOORN, THE NETHERLANDS

Hereby, JVCKENWOOD declares that the radio equipment “KDC-BT950DAB/KDC-BT450DAB/KMM-BT407DAB/
KMM-DAB307” is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available
at the following internet address: http://www.kenwood.com/cs/ce/eudoc/

SOFTWARE LICENSE AGREEMENT

The software embedded in the Product (hereinafter the “Licensed Software”) provided by Licensor is copyrighted to or sublicensable by the Licensor, and this Agreement provides for the terms and conditions which Users shall follow in order to use the Licensed Software.

The User shall use the Licensed Software by agreeing with the terms of this Software License Agreement. This Agreement shall be deemed completed at the time the User (hereinafter the “User”) initially used the Product in which the “Licensed Software” is embedded.

The Licensed Software may include the software which has been licensed to the Licensor directly or indirectly from any third party. In such case, some third parties require the Users to follow their conditions for use separately from this Software License Agreement. Such software shall not be subject to this Agreement, and the Users are urged to read the “Important Notice concerning the Software” to be provided separately below.

Article 1 General Provision

The Licensor shall grant to the User a non-exclusive and non-transferable (other than the exceptional case referred to in Article 3, Paragraph 1) licensed to use the Licensed Software within the country of the User. (the country where the User bought the Product (hereinafter the “Country”)

Article 2 License

The license granted under this Agreement shall be the right to use the Licensed Software in the Product.
The User shall not duplicate, copy, modify, add, translate or otherwise alter, or lease the Licensed Software and any related documents, whether in whole or in part.
The use of the Licensed Software shall be limited to personal purpose, and the Licensed Software shall not be distributed, licensed or sub-licensed whether it is for commercial purpose or not.
The User shall use the Licensed Software according to the directions described in the operation manual or help file, and is prohibited to use or duplicate any data in a manner violating the Copyright Law or any other laws and regulations by applying whole or a part of the Licensed Software.

Article 3 Conditions for Grant of License

When the User transfers the Product, it may also transfer the license to use the Licensed Software embedded in the Product (including any related materials, updates and upgrades) on condition that no original, copies or related materials continue in the possession of the User, and that the User shall cause the transferee to comply with this Software License Agreement.
The User shall not carry out reverse engineering, disassembling, decompiling or any other code analysis works in connection with the Licensed Software.

Article 4 Right pertaining to the Licensed Software

Any and all copyrights and other rights pertaining to the Licensed Software and related documents shall belong to the Licensor or the original holder of the right who granted to the Licensor the license or sublicense for the Licensed Software (hereinafter the “Original Right holder”), and the User shall not be entitled to any right other than the license granted hereunder, in respect of the Licensed Software and any related documents.

Article 5 Indemnification of Licensor

Neither the Licensor nor the Original Right holder shall be liable for any damage incurred by the User or any third party due to the exercise of the license granted to the User under this Agreement, unless otherwise restricted by law.
The Licensor will offer no guarantee for the merchantability, convertibility and consistency with certain objective of the Licensed Software.

Article 6 Liability to Third Party

If any dispute has arisen with any third party due to an infringement upon a copyright, patent or any other intellectual property right that was caused by the User’s use of the Licensed Software, the User shall settle such dispute at its own cost and hold the Licensor and the Original Rightholder harmless from any inconvenience it may cause.

Article 7 Confidentiality

The User shall keep the confidentiality of such portion of the Licensed Software, related documents thereof or any other information to be granted under this Agreement, as well as the conditions of this Agreement as has not yet entered the public domain, and shall not disclose or divulge the same to any third party without approval of the Licensor.

Article 8 Termination

In case the User falls under any of the events described in the following items, the Licensor may immediately terminate this Agreement or claim that the User compensates for the damage incurred by the Licensor due to such event:

(1) when the User violated any provision of this Agreement; or
(2) when a petition has been filed against the User for an attachment, provisional attachment, provisional disposition or any other compulsory execution.

Article 9 Destruction of the Licensed Software

If this Agreement is terminated pursuant to the provision of Article 8, the User shall destroy the Licensed Software, any related documents and copies thereof within two (2) weeks from such date of termination.

Article 10 Protection of Copyright

1. The copyright and all the other intellectual property rights relating to the Licensed Software shall belong to the Licensor and the Original Rightholder, and in no event shall they be under the ownership of the User.
2. The User shall, whenever it uses the Licensed Software, comply with any laws relating to the copyright and other intellectual property rights.

Article 11 Export Restriction

1. It is prohibited to export the Licensed Software and any related documents outside the country of the User (including transmission thereof outside the country of the User via Internet of other communication tools).
2. The User shall understand that the Licensed Software shall be subject to the export restrictions adopted by the country of User and any other countries.
3. The User shall agree that the software will be subject to any and all applicable international and domestic laws (including the export control regulation of the country of User and any other countries, and any restrictions concerning the end-users, the use by end-users and importing countries to be provided by the country of User and any other countries, and any other governmental authorities).

Article 12 Miscellaneous

1. In the event any part of this Agreement is invalidated by operation of law, the residual provisions shall continue in force.
2. Matters not stipulated in this Agreement or any ambiguity or question raised in the construction of this Agreement shall be provided or settled upon good-faith consultation between the Licensor and the User.
3. The Licensor and the User hereby agree that this Agreement is governed by the laws of Japan, and any dispute arising from, and relating to the rights and obligations under, this Agreement shall be submitted to the exclusive jurisdiction of the Tokyo District Court for its first instance.

Important Notice concerning the Software

-jansson
Copyright (c) 2009-2012 Petri Lehtinen <>

Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the “Software”), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:

The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.

THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

-cJSON
Copyright (c) 2009 Dave Gamble

The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.

-CMP
The MIT License (MIT)
Copyright (c) 2014 Charles Gunyon

The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.

nanopb
Copyright (c) 2011 Petteri Aimonen <>

This software is provided ‘as-is’, without any express or implied warranty. In no event will the authors be held liable for any damages arising from the use of this software.

Permission is granted to anyone to use this software for any purpose, including commercial applications, and to alter it and redistribute it freely, subject to the following restrictions:

The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a product, an acknowledgment in the product documentation would be appreciated but is not required.
Altered source versions must be plainly marked as such, and must not be misrepresented as being the original software.
This notice may not be removed or altered from any source distribution.

sha2
AUTHOR: Aaron D. Gifford – http://www.aarongifford.com/
Copyright (c) 2000-2001, Aaron D. Gifford
All rights reserved.
You may obtain a copy of the license at
https://opensource.org/licenses/BSD-3-Clause

Posix
Copyright (c) 1990, 1993
The Regents of the University of California. All rights reserved.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
All advertising materials mentioning features or use of this software must display the following acknowledgement: This product includes software developed by the University of California, Berkeley and its contributors.
Neither the name of the University nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

Developed at SunPro, a Sun Microsystems, Inc. business.
Permission to use, copy, modify, and distribute this software is freely granted, provided that this notice is preserved.

License to copy and use this software is granted provided that it is identified as the “RSA Data Security, Inc. MD4 Message-Digest Algorithm” in all material mentioning or referencing this software or this function.

Permission to use, copy, modify and distribute this software and its documentation is hereby granted, provided that both the copyright notice and this permission notice appear in all copies of the software, derivative works or modified versions, and any portions thereof, and that both notices appear in supporting documentation.

CARNEGIE MELLON ALLOWS FREE USE OF THIS SOFTWARE IN ITS “AS IS” CONDITION. CARNEGIE MELLON DISCLAIMS ANY LIABILITY OF ANY KIND FOR ANY DAMAGES WHATSOEVER RESULTING FROM THE USE OF THIS SOFTWARE.

Carnegie Mellon requests users of this software to return to

Software Distribution Coordinator or Software.
CS.CMU.EDU
School of Computer Science
Carnegie Mellon University
Pittsburgh PA 15213-3890
any improvements or extensions that they make and grant Carnegie the rights to redistribute these changes.

License is also granted to make and use derivative works provided that such works are identified as “derived from the RSA Data Security, Inc. MD4 Message-Digest Algorithm” in all material mentioning or referencing the derived work.

RSA Data Security, Inc. makes no representations concerning either the merchantability of this software or the suitability of this software for any particular purpose. It is provided “as is” without express or implied warranty of any kind.

You may redistribute unmodified or modified versions of this source code provided that the above copyright notice and this and the following conditions are retained.

This software is provided “as is”, and comes with no warranties of any kind. I shall in no event be liable for anything that happens to anyone/anything when using this software.
These notices must be retained in any copies of any part of this documentation and/or software.

T-Kernel 2.0
This product uses the source code of T-Kernel 2.0 under T-License 2.0 granted by T-Engine Forum
(www.tron.org)

BSD-3-Clause
Copyright (c) 2000-2001, Aaron D. Gifford
All rights reserved.
You may obtain a copy of the license at
https://opensource.org/licenses/BSD-3-Clause

LFS Subsystem
Copyright The Regents of the University of California. All rights reserved.

You may obtain a copy of the license at
https://directory.fsf.org/wiki/License:BSD-4-Clause

Accordo2 Player
Apache License
Licensed under the Apache License,
Version 2.0, January 2004(the “License”);
You may obtain a copy of the license at
http://www.apache.org/licenses/LICENSE-2.0

Installation/Connection

This section is for the professional installer.
For safety’s sake, leave wiring and mounting to professionals. Consult the car audio dealer.

WARNING

The unit can only be used with a 12 V DC power supply, negative ground.
Disconnect the battery’s negative terminal before wiring and mounting.
Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire (black) to prevent a short circuit.
To prevent short circuit:
- Insulate unconnected wires with vinyl tape.
- Be sure to ground this unit to the car’s chassis again after installation.
- Secure the wires with cable clamps and wrap vinyl tape around the wires that comes into contact with metal parts to protect the wires.

CAUTION

Install this unit in the console of your vehicle. Do not touch the metal parts of this unit during and shortly after use of the unit. Metal parts such as the heat sink and enclosure become hot.
Do not connect the wires of speakers to the car chassis or Ground wire (black), or connect them in parallel.
Mount the unit at an angle of less than 30º.
If your vehicle wiring harness does not have the ignition terminal, connect Ignition wire (red) to the terminal on the vehicle’s fuse box which provides 12 V DC power supply and is turned on and off by the ignition key.
Keep all cables away from heat dissipate metal parts.
After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly.
If the fuse blows, first make sure the wires are not touching car’s chassis, then replace the old fuse with one that has the same rating.

Basic procedure

Remove the key from the ignition switch, then disconnect the terminal of the car battery.
Install the DAB antenna. See “Installing the DAB antenna” on page 4.
Connect the wires properly. See “Wiring connection” on page 3.
Install the unit to your car. See the following “Installing the unit (in-dash mounting)”.
Connect the terminal of the car battery.
Press B SRC to turn on the power.
Detach the faceplate and reset the unit within 5 seconds. See “How to reset” on page 7, 8.

Installing the unit (in-dash mounting)

Removing the unit

Part list (supplied)

(A) Faceplate (×1)
(B) Trim plate (×1)
(C) Mounting sleeve (×1)
(D) Wiring harness (×1)
(E) Extraction key (×2)

Wiring connection

a. Light blue/yellow: To the steering wheel remote control adapter
b. Blue/white: To the power control terminal when using the optional power amplifier or to the antenna control terminal in the vehicle
c. Brown: To connect the Kenwood navigation system, refer your navigation manual
d. Yellow: Battery wire
e. Red: Ignition wire
f. Red: A7 from ISO connector
g. Yellow: A4 from ISO connector

Installing the DAB antenna

Connect the DAB antenna to the DAB antenna jack. (Page 3)

DAB antenna is supplied for KDC-BT950DAB/ KDC-BT450DAB/ KMM-BT407DAB. For details, see the following pages.
For KMM-DAB307, you need to purchase the DAB antenna separately.
For details, refer to the instruction manual supplied with the DAB antenna.

CAUTION

• The film antenna (F) is exclusively for use inside the vehicle.
• Do not install at the following locations:
– where it may block the driver’s view.
– where it may obstruct the operation of safety devices such as air bags.
– on movable glass surfaces such as the rear hatch.
– at side of vehicle (e.g. door, front quarter window).
– on rear window.
• Signal strength will weaken when installed at the following locations:
– on IR reflecting glass or locations covered with mirror type glass film.
– where it overlaps with genuine radio antenna (pattern).
– where it overlaps with window heating wires.
– on glass that blocks radio signals (e.g. IR reflecting glass, thermal insulation glass).
• Poor reception may occur:
– due to noise when windscreen wiper, air conditioner, or motor is turned on.
– depending on the direction of the broadcast station with respect to the vehicle (antenna).
• Thoroughly wipe oil and dirt from the pasting surface with the supplied cleaner (I).
• Do not bend or damage the film antenna (F).
• It may not be possible to install on certain vehicles.
• Check the cable routing of the film antenna (F) and amplifier unit (G) before pasting.
• Do not apply any glass cleaner after pasting the film antenna (F).

Part list (supplied)

(F) Film antenna (×1)
(G) Amplifier unit (cable with booster, 3.5 m) (×1)
(H) Cable clamper (×3)
(I) Cleaner (×1)

Determine the antenna installation position

The direction of the film antenna (F) changes depending on whether the film antenna (F) is installed on the right side or left side.
Be sure to check the installation location of film antenna (F) before installing. Film antenna cannot be re-pasted.
Separate from other antennas by at least 100 mm.
Do not paste the amplifier unit (G) on the ceramic line (black part) around the front glass. Because there is not enough adhesion.

* Paste the earth sheet of the amplifier unit (G) on the metal part of the front pillar.

CAUTION

When installing the antenna cable inside the front pillar with the air bag installed

The front pillar cover is secured with a special clip which may need to be replaced when it is removed. Contact your vehicle dealer for details on removing the front pillar cover and availability of replacement parts.
Install the amplifier unit (G) above the air bag so that it does not obstruct the operation of the air bag.

Installation overview
The antenna should be installed on the passenger side for safety.

Antenna installation

Remove the front pillar cover of your car.
Clean the windscreen with the supplied cleaner (I).
– Wait until the glass surface is completely dry before proceeding.
– Warm the surface of the windscreen with defroster if it is cold (during winter).
Remove the separator (tag 1) of film antenna (F) horizontally and paste the antenna on the windscreen.
Do not touch the pasting surface (adhesive side) of the film antenna (F).
Rub the film antenna gently onto the windscreen in the direction of the arrow shown to allow it to stick firmly.
Remove the separator (tag 2) of film antenna (F) vertically.
Set the position of the protrusion of the amplifier unit (G) with the ▼ mark on the film antenna (F) and paste.
Do not touch the lead terminal or the pasting surface (adhesive side) of the amplifier unit (G).
• When installing the antenna on the right side
• When installing the antenna on the left side
Remove the film covering the earth sheet and paste the earth sheet on the metal part of the vehicle.
Provide sufficient leeway for the earth sheet so that it does not interfere with the interior parts (front pillar cover). Also take care that the interior parts do not interfere with the amplifier unit (G).
Wire the antenna cables.
Use cable clamper (H) to secure the antenna to the pillar at several positions.
Attach the front pillar cover back to its original position.
Be sure not to damage the earth sheet and amplifier unit (G) when covering.
Connect the amplifier unit (G) to the DAB antenna jack on the rear of the unit.

Note:
Make sure [DAB ANT POWER] is set to [ON] on the [FUNCTION] menu in standby mode. [ON] is selected initially.

Before Use

IMPORTANT

To ensure proper use, please read through this Guide before using this product. It is especially important that you read and observe Warnings and Cautions in this Guide.
Please keep the Guide in a safe and accessible place for future reference.

WARNING

Do not operate any function that takes your attention away from safe driving.

CAUTION

Volume setting:
• Adjust the volume so that you can hear sounds outside the car to prevent accidents.
• Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.

General:
• Avoid using the external device if it might hinder safe driving.
• Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.
• Never put or leave any metallic objects (such as coins or metal tools) inside the unit to prevent a short circuit.
• KDC-BT950DAB/ KDC-BT450DAB: If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to evaporate.
• USB rating is indicated on the main unit. To view, detach the faceplate.
• Depending on the types of cars, the antenna will automatically extend when you turn on the unit with the antenna control wire connected. Turn off the unit or change the source to STANDBY when parking at a low ceiling area.

Basics

Faceplate

Getting Started

Select the display language, acknowledge the crossover type and cancel the demonstration

When you turn on the power for the first time (or [FACTORY RESET] is set to [YES] ), the display shows: “SEL LANGUAGE” > “PRESS” > “VOLUME KNOB”

Turn the volume knob to select [EN] (English) / [RU] (Russian) / [SP] (Spanish) / [FR] (French) / [GE]* (German), then press the knob.
[EN] is selected for the initial setup.
Then, the display shows: “2-WAY X ’ OVER” or “3-WAY X ’ OVER” > “PRESS” “VOLUME KNOB” > “TO CONFIRM”.
Press the volume knob to acknowledge the current crossover type.
Then, the display shows: “CANCEL DEMO” > “PRESS” > “VOLUME KNOB”.
Press the volume knob again.
[YES] is selected for the initial setup.
Press the volume knob again.
“DEMO OFF” appears.

* Only for KDC-BT950DAB.

Set the clock and date

Press the volume knob to enter [FUNCTION] .
Turn the volume knob to select [CLOCK] , then press the knob.
To adjust the clock
Turn the volume knob to select [CLOCK ADJUST] , then press the knob.
Turn the volume knob to make the settings, then press the knob.
Set the time in the order of “Hour” “Minute”.
Turn the volume knob to select [CLOCK FORMAT] , then press the knob.
Turn the volume knob to select [12H] or [24H] , then press the knob.
To set the date
Turn the volume knob to select [DATE FORMAT] , then press the knob.
Turn the volume knob to select [DD/MM/YY] or [MM/DD/YY] , then press the knob.
Turn the volume knob to select [DATE SET] , then press the knob.
Turn the volume knob to make the settings, then press the knob.
Set the date in the order of “Day” > “Month” > “Year” or “Month” > “Day” > “Year”.
Press and hold to exit.

To return to the previous setting item, press .

Set the other optional settings

You can only set the following items while the unit is in STANDBY source.

Press SRC repeatedly to enter STANDBY.
Press the volume knob to enter [FUNCTION] .
Turn the volume knob to select an item (see the following table), then press the knob.
Repeat step 3 until the desired item is selected or activated.
Press and hold to exit.

To return to the previous setting item, press .

Digital Radio

About DAB (Digital Audio Broadcasting)
DAB is one of the digital radio broadcasting systems available today. It can deliver digital quality sound without any annoying interference or signal distortion. Furthermore, it can carry text, pictures and data. In contrast to FM broadcast, where each program is transmitted on its own frequency, DAB combines several programs (called “services”) to form one
“ensemble.”
The “primary component” (main radio station) is sometimes accompanied by a “secondary component” which can contain extra programs or other information.

Preparation:

Connect the DAB antenna (supplied/separately purchased) to the DAB antenna jack on the rear of the unit.
Press SRC repeatedly to select DIGITAL AUDIO.
Press and hold (LIST UPDATE) to start the Service List update. “UPDATED” appears when update completes.

Search for an ensemble

Press SRC repeatedly to select DIGITAL AUDIO.
Press BAND repeatedly to select DB1/DB2/DB3.
Press and hold to search for an ensemble.
Press to select an ensemble, service or component to listen.

Settings in memory

You can store up to 18 services.

Store a service
Press and hold one of the number buttons (1 to 6).

Select a stored service
Press one of the number buttons (1 to 6).

Analog Radio

Search for a station

Press SRC repeatedly to select RADIO.
Press BAND repeatedly to select FM1/FM2/FM3/MW/LW.
Press to search for a station.

Settings in memory

You can store up to 18 stations for FM and 6 stations for MW/LW.

Store a station
While listening to a station….
Press and hold one of the number buttons (1 to 6).

Select a stored station
Press one of the number buttons (1 to 6).

CD/USB/iPod

Selectable source:
KDC-BT950DAB: CD/USB/iPod USB or iPod BT
KDC-BT450DAB: CD/USB
KMM-BT407DAB/ KMM-DAB307: USB

Start playback

The source changes automatically and playback starts when you load a disc or attach a device (USB device/ iPod/iPhone) to the USB input terminal.

Functions Settings

Press the volume knob to enter [FUNCTION] .
• For KMM-DAB307: Press AUD to enter [AUDIO CONTROL] directly.
Turn the volume knob to select an item, then press the knob.
Repeat step 2 until the desired item is selected or activated.
Press and hold to exit.

To return to the previous setting item, press .

• Refer to the INSTRUCTION MANUAL on the following website for the detailed explanation of each item: <www.kenwood.com/cs/ce/>
• The availability of each item vary depending on the model.

[FUNCTION] menu items

* Applicable only while talking on the phone.

Examples of some well-used settings

Subwoofer Level Setting

Note:
For KDC-BT450DAB/ KMM-BT407DAB/ KMM-DAB307: You need to set [SWITCH PREOUT] to [SUB-W] in standby mode before you can make the above settings.

Illumination Color Setting

For KDC-BT950DAB: You can set your preferred illumination color for each zone.

Other Information

For playback operations of AUX and Spotify sources, refer to the INSTRUCTION MANUAL on the following website:
<www.kenwood.com/cs/ce/>
• The availability of each source vary depending on the model.

Note for specifications
Bluetooth Frequency Range: 2.402 GHz — 2.480 GHz
Bluetooth RF Output Power (E.I.R.P.): +4 dBm (MAX), Power Class 2
Speaker Impedance: 4 Ω — 8 Ω
Operating Voltage: 12 V DC car battery

Bluetooth®

(for KDC-BT950DAB/ KDC-BT450DAB/ KMM-BT407DAB)

Depending on the Bluetooth version, operating system and the firmware version of your mobile phone, Bluetooth features may not work with this unit.
Be sure to turn on the Bluetooth function of the device to make the following operations.
Signal conditions vary depending on the surroundings.

Connect the microphone

Connect the supplied microphone to the microphone input jack on the rear panel.

Pair and connect a Bluetooth device for the first time

Press SRC to turn on the unit.
Search and select the name of your receiver (“KDC-BT950DAB”/“KDC-BT450DAB”/“KMM-BT407DAB”) on the Bluetooth device.
“PAIRING” > “PASS XXXXXX” > “Device name” > “PRESS” > “VOLUME KNOB” appears on the display.
- For some Bluetooth devices, you may need to enter the Personal Identification Number (PIN) code immediately after searching.
Press the volume knob to start pairing. “PAIRING OK” appears when pairing is completed.

Once pairing is completed, Bluetooth connection is established automatically.

For KDC-BT950DAB:
– “BT1” and/or “BT2” indicator on the faceplate lights up.
– “” indicator lights up to show the strength of the battery and signal of the connected device.
For KDC-BT450DAB/ KMM-BT407DAB: “BT1” and/or “BT2” indicator on the display window lights up.

Answer a call

Press or the volume knob or one of the number buttons (1 to 6).
• To adjust the phone volume [00] to [35] , turn the volume knob.
• To end a call, press .

Audio player via Bluetooth

Press SRC repeatedly to select BT AUDIO.
• Pressing enters BT AUDIO directly.
Operate the audio player via Bluetooth to start playback.

Windows Media is a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. This product is protected by certain intellectual property rights of Microsoft. Use or distribution of such technology outside of this product is prohibited without a license from Microsoft.
Use of the Made for Apple badge means that an accessory has been designed to connect specifically to the Apple product(s) identified in the badge and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with an Apple product may affect wireless performance.
Apple, iPhone, iPod, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries.
IOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license.
Android is a trademark of Google LLC.
SPOTIFY and the Spotify logo are among the registered trademarks of Spotify AB.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by JVCKENWOOD Corporation is under license. Other trademarks and trade names are those of their respective owners.

Download

KENWOOD Receiver User Manual

Was this manual helpful?