Panasonic Digital Wireless Stereo Headphones Owner’s Manual

Panasonic Digital Wireless Stereo Headphones

Thank you for purchasing this product. Please read these instructions carefully before using this product, and save this manual for future use.

Accessories

Please check and identify the supplied accessories.
To order accessories, contact the dealer from whom you have made your purchase.

1 x USB charging cord
1 x Detachable cord

Only for U.S.A.:
To order accessories, refer to “Limited Warranty”.

Maintenance

Clean this unit with a dry and soft cloth.

• Do not use solvents including benzine, thinner, alcohol, kitchen detergent, a chemical wiper, etc. This might cause the exterior
  case to be deformed or the coating to come off.
  Keeping the battery performance.
• During the long period of disuse, full charge this unit once every 6 months to keep the battery performance.

IMPORTANT SAFETY INSTRUCTIONS

Read these operating instructions carefully before using the unit. Follow the safety instructions on the unit and the applicable safety instructions listed below. Keep these operating instructions handy for future reference.

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
    
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Safety precautions

Unit

• Avoid using or placing this unit near sources of heat.
• Do not listen with this unit at high volume in places where you need to hear sounds from the surrounding environment for safety, such as at railroad crossings, and construction sites.
• Wide band characteristic voltage equal or larger than 75 mV.
• Keep this unit away from something susceptible to the magnetism.
  Such devices as a clock may not operate correctly.
• When using this unit in an airplane, heed the instructions given by the airline company. Some airlines may forbid your using the unit.
  For further details, contact the airline you will be flying with.

Allergies

• Discontinue use if you experience discomfort with the ear pads or any other parts that directly contact your skin.
• Continued use may cause rashes or other allergic reactions.

 Precautions for listening with the Headphones

• Excessive sound pressure from earphones and headphones can cause hearing loss.
• Do not use your headphones at a high volume. Hearing experts advise against continuous extended play.
• If you experience a ringing in your ears, reduce volume or discontinue use.
• Do not use while operating a motorized vehicle. It may create a traffic hazard and is illegal in many areas.
• You should use extreme caution or temporarily discontinue use in potentially hazardous situations.

 

1. Remove the right ear pad to view certification information.
   
2. Certification information is indicated on the speaker plate portion , which becomes visible when the right ear pad (R side) is removed.
   
3. To attach the ear pad, fit the part of the ear pad into the part .
   

If you pull the ear pad too much, the ear pad can tear.

Declaration of Conformity (DoC)

Hereby, “Panasonic Corporation” declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.

Customers can download a copy of the original DoC to our RE products from our DoC server: http://www.ptc.panasonic.eu

Contact to Authorized Representative:
Panasonic Marketing Europe GmbH, Panasonic Testing Centre, Winsbergring 15, 22525 Hamburg, Germany

User memo:

Part names

1. Audio input terminal
2. [+] button
3. [ ] button
4. [–] button
5. Power/pairing LED
6. Microphone
7. Charging terminal (DC IN)
8. [NC] (Noise cancelling) switch
9. [BASS +]/[BASS –] button
10. Ear pads
11. Raised dot indicating the left side
    

Charging

The rechargeable battery (installed in the unit) is not charged initially. Charge the battery before using the unit.

Connect this unit to a computer () using the USB charging cord (supplied) ().

• The power/pairing LED (c) lights in red when charging is in progress. When charging is completed, the power/pairing LED will go out.
• It takes approx. 4 hours to charge the battery from empty to full.
• Check the direction of the terminals and plug in/out straight holding
  onto the plug. (It may result in malfunction by the deforming of the
  terminal if it is plugged in obliquely or in wrong direction.)
• It is not possible to turn the power on or connect to Bluetooth ® devices during charging.
• Make sure the computer is turned on and is not on standby or sleep mode.
• Do not use any other USB charging cords except the supplied one.
• When the battery starts running low during use of the unit, the blinking power/pairing LED will turn from blue to red. A beep will sound every 1 minute. When the battery runs out, an English guidance message will be heard and the power will turn off.
  

Turning the power on/off

Press and hold [ ] () of this unit for approx. 3 seconds until the power/pairing LED (blue) () blinks.

• A beep will sound, and the power/pairing LED (blue) will blink slowly.
  To turn the power off
  Press and hold [ ] for approximately 3 seconds. An English guidance message will be heard, and the power will be turned off.
• If the unit is not connected to a Bluetooth® device, an English guidance message will be heard and turn off the unit automatically approximately 5 minutes after you have stopped using it. (Auto power off) (Except for when noise cancelling is turned ON.)
• Auto power off does not work when the detachable cord (supplied) is connected.
  

Connecting a Bluetooth® device

Bluetooth® pairing

1. In the power-off state, press and hold [] of this unit until the power/pairing LED blinks.
   – When pairing a device for the first time: approx. 3 seconds
   – When pairing a second or subsequent devices: approx. 5 seconds
   ● This unit will start to search for a Bluetooth® device to connect to, and the power/pairing LED will light alternately in blue and red.
2. Turn on the power of the Bluetooth® device, and enable the Bluetooth® function.
3. Select “RB-M700B” from the Bluetooth® device’s menu.
   ● If prompted for a passkey, input the passkey “0000 (four zeros)” of this unit.
   ● When the power/pairing LED (blue) blinks twice every approx.
   2 seconds, pairing (registration) is completed. (Connection established)
   ● If connection to a device is not established within approximately
   5 minutes, the unit will be turned off. Perform pairing again.
   (Except for when noise cancelling is turned ON.)
   

Connecting a paired Bluetooth® device

1. Turn on this unit.
2. Perform steps 2 and 3 of “Bluetooth® pairing”. ( above)
   ● When the power/pairing LED (blue) blinks twice every approx.
   2 seconds, pairing (registration) is completed. (Connection established)

Using the headphones

When using the functions below that are indicated with the [ ] mark, connect the Bluetooth® device and the unit.

Listening to music []

Select and play the music on the Bluetooth® device.

• The unit’s headphones will output the music or the audio of the video being played back.

Remote controlling (Available only if your Bluetooth® device supports “AVRCP” Bluetooth® profiles) [] (Operation example)

Play / Pause: Press [ ] ().
Increase the volume: Press [–] ().
Decrease the volume: Press [+] ().
Forward to the start of next track: Press and hold [+] for approximately
2 seconds.
Return to the start of current track: Press and hold [–] for approximately 2 seconds.

• The volume can be adjusted in 31 levels (16 levels during calls).
  When the maximum or minimum volume is reached, a beep will sound.

Bass reactor

While playing back music or videos on a device connected via Bluetooth®

Press [BASS i] () or [BASS j] () to adjust the Bass reactor strength level.

• This unit vibrates along with the bass of the music or video being played back.
• Bass reactor strength level: Off ,-. Low ,-. Middle ,-. High (The default value is Low.)
• Even when the power is turned off, the setting before turning it off will be stored to memory.
• The playback time depends on the music source and the Bass reactor strength level.
• This may not be effective depending on the music or video being played back.
• If you feel ill while using the Bass reactor, set the Bass reactor to
  Off.
• Turn on this unit to use the Bass reactor when using this unit with the detachable cord (supplied) connected.
• Adjust the Bass reactor strength level and the volume so that the sound is not distorted.

Making a phone call [ ]

1.  Press [ ] () on the unit and answer the incoming call.
   ● (HFP only) To reject the incoming call, press [ ] twice quickly.
2. Start talking.
3. Press [ ] to end the phone call.
   ● (HFP only) It may be difficult to hear phone conversations when the unit is used in locations with loud ambient noise or in outdoor or other locations exposed to powerful winds. In that case, change the calling location or switch the calling device to the Bluetooth® enabled phone to continue the call. (Press [ ] on the unit twice quickly to switch.)
   ● You can have the Bluetooth® enabled phone make phone calls by using the microphone of the unit and an app of the Bluetooth® enabled phone.
   ( below, “Activating voice functions”)

Using noise cancelling

Setting noise cancelling to ON changes the volume and sound quality.

The sound quality is set to the optimum.

1. Set the [NC] switch (d) to ON.
2. Adjust the volume of the playback device.

• While using the noise cancelling function, a very small amount of noise which is generated from the circuit that reduces noise may be heard, but this is normal and not indicative of any trouble. (This very-low-level noise may be heard in quiet places or in the blank parts between tracks.)
• Howling may occur if you push the ear pads too strongly into your ears. Do not use the ear pads while continuously pushing them in.

Activating voice functions [ ]

You can use a button on this unit to activate Siri or other voice functions on your smartphone or similar device.
Press [ ] () of this unit twice quickly

Using the detachable cord (supplied)

While the power is turned off or the battery has no remaining charge, this unit can be used as normal headphones by connecting the detachable cord (supplied). ()

• If you connect the detachable cord (supplied) during Bluetooth® connection, the Bluetooth® connection will be lost.
• Noise may occur due to dirt on the plug. Clean the plug with a soft dry cloth if this occurs.
• Do not use any other detachable cords except the supplied one.
• When the detachable cord (supplied) is connected and the power is turned on, you can use the Bass reactor. However, the volume cannot be adjusted in this case.

Restoring to the factory settings

Charge the battery before restoring the unit.

1. While the power is turned off, press and hold [ ] (a) for at least 5 seconds until the power/pairing LED lights alternately in blue and red.
2. While the power/pairing LED is lighting alternately in blue and red, press and hold [i] (b) and [j] (c) at the same time for at least 5 seconds.

• The default settings will be restored after the power/pairing LED (blue) blinks fast and the unit turns off.
• When pairing a device again, delete the registering information (Device: “RB-M700B”) from the Bluetooth® device’s menu, and register this unit with the Bluetooth® device again. ( )
  

To remove the battery when disposing of this unit

• Disassemble after the battery runs out.
• Keep disassembled parts out of reach of children.

Regarding the handling of used battery

• Insulate the terminals with adhesive tape or similar material.
• Do not disassemble.

Battery

• Do not heat or expose to flame.
• Do not leave the battery in a car exposed to direct sunlight for a long period of time with doors and windows closed.
• Battery mishandling can cause electrolyte leakage which can damage items the leaked fluid comes into contact with. If electrolyte leaks from the battery, consult your dealer. Wash thoroughly with water if electrolyte comes in contact with any part of your body.
• When disposing of the battery, please contact your local authorities or dealer and ask for the correct method of disposal.

1. Remove the left ear pad.
2. Remove the 4 screws.
3. Remove the part in step 2.
4. Remove the battery, and cut off the wires one by one with scissors.
   

Troubleshooting

Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the remedies indicated in the chart do not solve the problem, refer to “Customer Services Directory” on the front page if you reside in the U.S.A., or refer to “CONTACT INFORMATION” on the front page if you reside in Canada, or consult your dealer for instructions.

No sound.

• Make sure that the unit and the Bluetooth® device are connected correctly. (  )
• Check if music is playing on the Bluetooth® device.
• Make sure that the unit is turned on and the volume is not set too low.
• Pair and connect the Bluetooth® device and the unit again. (  )
• Check if the Bluetooth® compatible device supports “A2DP” profile. For details on profiles, see “Listening to music” in “Owner’s Manual (PDF format)”. Also refer to the operating manual for the Bluetooth® compatible device.

Cannot adjust the volume.

• The control button does not work when the detachable cord (supplied) is used.

Low volume.

• Increase the volume of the unit. ( )
• Increase the volume on the Bluetooth® device.

Sound from the device is cut off. / Too much noise. / Sound quality is bad.

• Sound may be disrupted if signals are blocked. Do not fully cover this unit with the palm of your hand, etc.
• The device may be out of the 10 m (33 ft) communication range. Move the device closer to this unit.
• Remove any obstacle between this unit and the device.
• Switch off any wireless LAN device when not in use.

Music, etc., is distorted.

• While using the noise cancelling function, sound may be distorted if the Bass reactor strength level is High. Reduce the Bass reactor strength level and the volume until there is no distortion.

The device cannot be connected.

• Delete the pairing information for this unit from the Bluetooth ® device, then pair them again. (  )

You cannot hear the person on the other end of the call.

• Make sure that the unit and the Bluetooth® enabled phone are turned on.
• Check if the unit and the Bluetooth® enabled phone are connected.
  (   )
• Check the audio settings of the Bluetooth® enabled phone. Switch the
  calling device to the unit if it is set to the Bluetooth® enabled phone.
  (  )
• If the volume of the other person’s voice is too low, increase the volume
  of both the unit and the Bluetooth® enabled phone.

Cannot make a phone call.

• Check if the Bluetooth® compatible device supports “HSP” or “HFP” profile. For details on profiles, see “Listening to music” and “Making a phone call” in “Owner’s manual (PDF format)”. Also refer to the operating manual for the Bluetooth® enabled phone.

The unit does not respond.

• This unit can be reset when all operations are rejected. To reset the unit, connect the unit to a computer using the USB charging cord. (The pairing device information will not be deleted.)

Cannot charge the unit.

• Is the USB port you are currently using working properly? If your computer has other USB ports, unplug the connector from its current port and plug it into one of the other ports.
• If the measures mentioned above are not applicable, unplug the USB charging cord and plug it in again.
• If the charge time and operating time become shortened, the battery may have run down. (Number of charging times of the installed battery: Approximately 300)

The power/pairing LED does not light during charging. / Charging takes longer.

• Is the USB charging cord connected firmly to the USB terminal of the computer? ( )
• Make sure to charge in a room temperature between 10 °C and 35 °C (50 °F to 95 °F).

The power does not turn on.

• Is the unit being charged? The power cannot be turned ON during charging. ( )

The audio guidance language has changed.

• The audio guidance language can be switched.
  (Press and hold [ ] and [–] at the same time for at least 5 seconds.)

Specifications

General

Bluetooth® section

Headphone section

Speaker section

1. It may be shorter depending on the operating conditions.
2. The time required to charge the battery from empty to full.
   ● Specifications are subject to change without notice.

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Panasonic Corporation is under license.
Other trademarks and trade names are those of their respective owners.

Siri is a trademarks of Apple Inc., registered in the U.S. and other countries.

QR Code is a registered trademark of DENSO WAVE INCORPORATED.

Other system names and product names appearing in this document are in general the registered trademarks or trademarks of the respective developer companies.
Note that the TM mark and ® mark do not appear in this document.

Limited Warranty (ONLY FOR U.S.A.)

Panasonic Products Limited Warranty

Limited Warranty Coverage
If your product does not work properly because of a defect in materials or workmanship, Panasonic Corporation of North America (referred to as “the warrantor”) will, for the length of the period indicated on the chart below, which starts with the date of original purchase (“warranty period”), at its option either (a) repair your product with new or refurbished parts, (b) replace it with a new or a refurbished equivalent value product, or (c) refund your purchase price. The decision to repair, replace or refund will be made by the warrantor.

During the “Labor” warranty period there will be no charge for labor. During the “Parts” warranty period, there will be no charge for parts. This Limited Warranty excludes both parts and labor for non-rechargeable batteries, antennas, and cosmetic parts (cabinet). This warranty only applies to products purchased and serviced in the United States. This warranty is extended only to the original purchaser of a new product which was not sold “as is”.

Mail-In Service–Online Repair Request

Online Repair Request
To submit a new repair request and for quick repair status visit our Web Site at http://shop.panasonic.com/support

When shipping the unit, carefully pack, include all supplied accessories listed in the Owner’s Manual, and send it prepaid, adequately insured and packed well in a carton box. When shipping Lithium Ion batteries please visit our Web Site at http://shop.panasonic.com/support as Panasonic is committed to providing the most up to date information. Include a letter detailing the complaint, a return address and provide a daytime phone number where you can be reached. A valid registered receipt is required under the Limited Warranty.

IF REPAIR IS NEEDED DURING THE WARRANTY PERIOD, THE PURCHASER WILL BE REQUIRED TO FURNISH A SALES RECEIPT/PROOF OF PURCHASE INDICATING DATE OF PURCHASE, AMOUNT PAID AND PLACE OF PURCHASE. CUSTOMER WILL BE CHARGED FOR THE REPAIR OF ANY UNIT RECEIVED WITHOUT SUCH PROOF OF PURCHASE.

Limited Warranty Limits and Exclusions
This warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOT COVER normal wear and tear or cosmetic damage. The warranty ALSO DOES NOT COVER damages which occurred in shipment, or failures which are caused by products not supplied by the warrantor, or failures which result from accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty installation, set-up adjustments, miss adjustment of consumer controls, improper maintenance, power line surge, lightning damage, modification, introduction of sand, humidity or liquids, commercial use such as hotel, office, restaurant, or other business or rental use of the product, or service by anyone other than a Factory Service Center or other Authorized Servicer, or damage that is attributable to acts of God.

THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER “LIMITED WARRANTY COVERAGE”. THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY.
(As examples, this excludes damages for lost time, travel to and from the servicer, loss of or damage to media or images, data or other memory or recorded content. The items listed are not exclusive, but for illustration only.)
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. If a problem with this product develops during or after the warranty period, you may contact your dealer or Service Center. If the problem is not handled to your satisfaction, then write to:

Panasonic Corporation of North America
Consumer Affairs Department 8th Fl.
Two Riverfront Plaza
Newark NJ 07102-5490

PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY, ARE YOUR RESPONSIBILITY.

Limited Warranty (ONLY FOR CANADA)

Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario L4W 2T3
PANASONIC PRODUCT – LIMITED WARRANTY EXCHANGE PROGRAM

Panasonic Canada Inc. warrants this product to be free from defects in material and workmanship under normal use and for a period as stated below from the date of original purchase agrees to, at its option either (a) repair your product with new or refurbished parts, (b) replace it with a new or a refurbished equivalent value product, or (c) refund your purchase price. The decision to repair, replace or refund will be made by Panasonic Canada Inc.

This warranty is given only to the original purchaser, or the person for whom it was purchased as a gift, of a Panasonic  brand product mentioned above sold by an authorized Panasonic dealer in Canada and purchased and used in Canada, which product was not sold “as is”, and which product was delivered to you in new condition in the original packaging

IN ORDER TO BE ELIGIBLE TO RECEIVE WARRANTY SERVICE HEREUNDER, A PURCHASE RECEIPT OR OTHER PROOF OF DATE OF ORIGINAL PURCHASE, SHOWING AMOUNT PAID AND PLACE OF PURCHASE IS REQUIRED

LIMITATIONS AND EXCLUSIONS

This warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOT COVER normal wear and tear or cosmetic damage. The warranty ALSO DOES NOT COVER damages which occurred in shipment, or failures which are caused by products not supplied by Panasonic Canada Inc., or failures which result from accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty installation, set-up adjustments, miss adjustment of consumer controls, improper maintenance, power line surge, lightning damage, modification, introduction of sand, humidity or liquids, commercial use such as hotel, office, restaurant, or other business or rental use of the product, or service by anyone other than a Authorized Servicer, or damage that is attributable to acts of God.

Dry cell batteries are also excluded from coverage under this warranty.

THIS EXPRESS, LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT WILL PANASONIC CANADA INC. BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY. (As examples, this warranty excludes damages for lost time, travel to and from the Authorized Servicer, loss of or damage to media or images, data or other memory or recorded content. This list of items is not exhaustive, but for illustration only.)

In certain instances, some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, or the exclusion of implied warranties, so the above limitations and exclusions may not be applicable. This warranty gives you specific legal rights and you may have other rights which vary depending on your province or territory.

CONTACT INFORMATION

For product operation and information assistance, please visit our Support page: www.panasonic.ca/english/support
For defective product exchange within the warranty period, please contact the original dealer.

Useful information (Only for Latin American countries)

Customer Service

Customer Service Directory

Obtain products information and operative assistant; localize the closer distributor or Service Center; buy spare parts and accessories by our Web Site to Latin America or calling our Contact Center:

For Caribbean countries that speak English please enter this web site in order to find information of our products and operative assistant: www.panasonic.com/caribbean

Support Information

For The United Kingdom and Ireland customers

Sales and Support Information

Customer Communications Centre

• For customers within the UK: 0344 844 3899
• For customers within Ireland: 01 289 8333
• Monday – Friday 9:00 am – 5:00 pm (Excluding public holidays).
• For further support on your product, please visit our website:
  www.panasonic.co.uk

Direct Sales at Panasonic UK

• Order accessory and consumable items for your product with ease and confidence by phoning our Customer Communications Centre Monday – Friday 9:00 am – 5:00 pm (Excluding public holidays).
• Or go on line through our Internet Accessory ordering application at www.pas-europe.com.
• Most major credit and debit cards accepted.
• All enquiries transactions and distribution facilities are provided directly by Panasonic UK.
• It couldn’t be simpler!
• Also available through our Internet is direct shopping for a wide range of finished products. Take a browse on our website for further details.

For Australia

Panasonic Australia Pty. Ltd. 1 Innovation Road, Macquarie Park NSW 2113

Provides a 12 month parts & labour warranty on this product for manufacturing defects from date of purchase. In addition to your rights under this warranty, Panasonic products come with consumer guarantees that cannot be excluded under the Australian Consumer Law. If there is a major failure with the product, you can reject the product and elect to have a refund or to have the product replaced or if you wish you may elect to keep the goods and be compensated for the drop in value of the goods. You are also entitled to have the product repaired or replaced if the product fails to be of acceptable quality and the failure does not amount to a major failure.

For full details or to claim warranty please contact Panasonic Customer Care on 132 600 or visit www.panasonic.com.au.