Electrolux Ceramic Glass Hob User Manual

Electrolux Ceramic Glass Hob User Manual

SAFETY INFORMATION

Please read the user manual carefully and store in a handy place for later reference. Pass the user manual on to possible new owners of the cooktop.

Read the following carefully to avoid damage or injury.

This symbol indicates never to do this
This symbol indicates always do this

General safety

WARNING!

Please comply with these instructions. If you do not, any damage resulting is not covered by the warranty.

Correct use

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

Do not leave the appliance unattended during operation.

This appliance should be used only for normal domestic cooking and frying of food.

The appliance must not be used as a work surface or as a storage surface.

Additions or modifications to the appliance are not permitted.

Do not place or store flammable liquids, highly inflammable materials or fusible objects (e.g. plastic film, plastic, aluminium) on or near the appliance.

The appliance may only be installed and connected by trained, registered service engineers.

Built-in appliances may only be used after they have been built into suitable built-in units and work surfaces that meet standards.

In the event of faults with the appliance or damage to the glass ceramic (cracks, scratches or splits), the appliance must be switched off and disconnected
from the electrical supply, to prevent the possibility of an electric shock.

Repairs to the appliance must only be carried out by trained registered service engineers.

The cooking zones will become hot when you cook. Therefore, always keep small children away from the appliance.

The appliance is not intended for use by young children or infirm persons without supervision.

Children should be supervised to ensure that they do not play with the appliance.

SAFETY INFORMATION (CONTINUED)

Safety during use

Remove stickers and film from the glass ceramic.
There is the risk of burns from the appliance if used carelessly.
Cables from electrical appliances must not touch the hot surface of the appliance or hot cookware.
Overheated fats and oils can ignite very quickly. Warning! Fire hazard!
Switch the cooking zones off after each use.

WARNING
If the surface is cracked, switch off the appliance to avoid possibility of electric shock.

Safety when cleaning

For cleaning, the appliance must be switched off and cooled down.
For safety reasons, the cleaning of the appliance with steam jet or high pressure cleaning equipment is not permitted.

How to avoid damage to the appliance

The glass ceramic can be damaged by objects falling onto it.
The edge of the glass ceramic can be damaged by being knocked by the cookware.
Cookware made of cast iron, cast aluminium or with damaged bottoms can scratch the glass ceramic if pushed across the surface.
Before spillage can become burnt on to the cooking surface, remove it with a damp cloth.
To avoid damaging cookware and glass ceramics,
do not allow saucepans or frying pans to boil dry.
Do not use the cooking zones with empty cookware or without cookware.
Do not let cookware boil dry to prevent damage to cookware and the ceramic glass.
Do not cover the parts of the appliance with aluminium foil.
Please note: Damage including broken glass or scratches caused by misuse outlined above is not covered under warranty.

PRODUCT DESCRIPTION

COOKING SURFACE LAYOUT

1. Single cooking zone 1200W
2. Single cooking zone 1800W
3.  Single cooking zone 1200W
4. Control panel
5. Triple cooking zone 2300/1600/800W

EHC944BB

1. Single cooking zone 1200W
2. Single cooking zone 1200W
3. Single cooking zone 1800W
4. Control panel
5. Triple cooking zone 2300/1600/800W

PRODUCT DESCRIPTION (CONTINUED)

CONTROL PANEL LAYOUT

1. Lock with pilot light
2. Sets all operating zones to a keep warm setting
3. Display
4. Cooking zone indicators of Timer
5. Timer display
6. Control bar to set a heat setting
7. Heat setting display
8. On/Off with power indicator
9. Triple ring cooking zone
10.  Timer
11. To activate and deactivate the Automatic heat up function
12. To activate and deactivate the manual mode of the Hob2Hood function

TOUCH CONTROL SENSOR FIELDS

The appliance is operated using Touch Control sensor fields. Functions are controlled by touching sensor fields and confirmed by displays and acoustic signals. Touch
the sensor fields from below, without covering other sensor fields.

HEAT SETTING DISPLAYS

OPTIHEAT CONTROL (3 STEP RESIDUAL HEAT INDICATOR)

WARNING!

There is a risk of burns from residual heat. The indicator shows the level of the residual heat.

IMPORTANT!
Residual heat can be used for melting and keeping food warm.

OPERATING INSTRUCTIONS

Switching the appliance on and off

IMPORTANT!

After switching on, within approx. 10 seconds a heat setting or a function must be set, otherwise the appliance automatically switches itself off.

Setting the heat setting

To set or change the heat setting: touch the control bar at the correct heat setting or move your finger along the
control bar until you reach the correct heat setting.

IMPORTANT!

The keep warm setting lies between and . It is used to keep food warm.

Switching the outside ring on and off By switching the outside rings on or off, the effective heating surface can be matched to the size of the
cookware. There are three indicators on the control panel that show which rings have been activated. To activate the inner ring: touch the sensor field. The left indicator comes on.
To activate the centre ring: touch the same sensor field
again. The middle indicator comes on.
To activate the outer ring: touch the sensor field again. The right indicator comes on.
To deactivate the outer ring: touch the sensor field until the indicator goes out.

IMPORTANT!

When you activate the zone but do not activate the outer ring the light that comes out from the zone may cover the outer ring. It does not mean that the outer ring is activated.
To see if the ring is activated check the indicator.

Locking/unlocking the control panel

The control panel, with the exception of the “On/Off” sensor field, can be locked at any time in order to prevent the settings being changed e.g. by wiping over the panel with
a cloth.

IMPORTANT!

When you switch the appliance off, the locking function is automatically switched off.

Using the automatic heat up function

Activate this function to get a desired heat setting in a shorter time. When it is one, the zone operates at the highest setting in the beginning and then continues to cook
at the desired heating setting. To activate the function for a cooking zone, press . ( comes on). Immediately touch a desired heat setting. After 3 seconds, comes on.

IMPORTANT!
To activate the function, the cooking zone must be cold.

The child safety device
The child safety device prevents unintentional use of the appliance.

Switching on the child safety device:

• Start the hob with . Do not set the heat settings.
• Touch for 4 seconds. The symbol comes on.
•  The child safety device is switched on.
  Switching off the child safety device:
• Start the hob with . Do not set the heat settings. Touch for 4 seconds. The symbol comes on.
• Stop the hob with .
• The child safety device is switched off.

IMPORTANT!

The child safety device can only be switched on and off, if no heat setting is set.

Overriding the child safety device:

The child safety device can be switched off in this way for a single cooking session; it remains activated afterwards.

• Start the hob with . The symbol comes on.
• Touch for 4 seconds. The symbol comes on. Until the appliance is next switched off, it can used as normal. After switching off the appliance, the child safety
  device is active again.

IMPORTANT!

After overriding the child safety device, a heat setting or a function must be set within approx. 10 seconds, otherwise the appliance automatically switches itself off.

Hob2Hood

This is an advanced automatic function which connects the hob to a special hood. Both the hob and the hood have an infra-red signal communicator. The speed of the fan is
defined automatically on the basis of the mode setting and the temperature of the hottest cooking zone on the hob. You can also operate the fan from the hob manually.

IMPORTANT!

For most hoods, the remote system is originally deactivated. Activate it before you use the function. For more information refer to your hood user manual.

Operating the function automatically

The default automatic mode from the factory is H5. You can change the automatic mode by following the instructions below. When you activate the job the hood
will adjust the fan speed automatically. Please note the below table is a guide, the fan speed varies depending on the temperature measured on the cooking zones of
the cooktop which can be affected by the heat setting(s) selected as well as the size and volume of what you are cooking.

Automatic modes

1. The hob detects the boiling process and activates fan speed in accordance with automatic mode.
2. The hob detects the frying process and activates fan speed in accordance with automatic mode.
3. This mode activates the fan and the light and does not rely on the temperature.

Using the timer

IMPORTANT!
If a heat setting is set on this cooking zone in addition to a countdown timer, the cooking zone is switched off after the time set has elapsed

IMPORTANT!
If a cooking zone is switched off, the timer function set is also switched off.

IMPORTANT!
If the pilot light is flashing more slowly, the heat setting can be set or modified.

IMPORTANT!
If other timer functions are set, after a few seconds the shortest remaining time of all the timer functions is displayed and the corresponding pilot light flashes.

Setting the time

Switching off the timer function

Changing the time

Displaying the time remaining for a cooking zone

Switching off the acoustic signal

Automatic switch off
The function deactivates the hob automatically if:

• All cooking zones are deactivated
• You do not set the heat setting after you activate the hob,
• You spill something or put something on the control panel for more than 10 seconds (a pan, a cloth, etc.). An acoustic signal sounds and the hob deactivates. Remove the object or clean the control panel.
• You do not deactivate a cooking zone or change the heat setting. After some time comes on and the hob deactivates.
  

Information on acrylamides

According to the latest scientific knowledge, intensive browning of food, especially in products containing starch, can constitute a health risk due to acrylamides. Therefore we recommend cooking at the lowest possible temperatures and not browning foods too much.

Cookware

• You can recognise good cookware from the bottoms of the pans. The bottom should be as thick and flat as possible.
• Cookware made of enamelled steel or with aluminium or copper bottoms can leave discolorations on the glass ceramic surface which are difficult or impossible to remove.

Energy saving

• Always place cookware on the cooking zone before it is switched on.
• Switch cooking zones off before the end of the cooking time, to take advantage of residual heat.
• If possible, always place lids on the pans.
  
• Bottom of pans and cooking zones should be the same size.
  

  CARE AND CLEANING

WARNING!

Watch out! Risk of burns from residual heat.

WARNING!

Sharp objects and abrasive cleaning materials will damage the appliance. Clean with water and washing up liquid.

WARNING!

Sharp cleaning agents will damage the appliance. Remove residues with water and washing up liquid.

Cleaning the appliance after each use

1. Wipe the appliance with a damp cloth and a little washing up liquid.
2. Rub the appliance dry using a clean cloth.

Removing deposits

1) *Scrapers and cleaners for glass ceramic and stainless steel can be purchased in specialized shops.

Removing deposits

1. Place a scraper on the glass ceramic surface at an angle.
2. Remove residues by sliding the blade over the surface.
3. Wipe the appliance with a damp cloth and a little washing up liquid.
4. Rub the appliance dry using a clean cloth.

IMPORTANT!

Remove stubborn residues with a cleaner for glass ceramic or stainless steel.

IMPORTANT!

Scratches or dark stains on the glass ceramic that cannot be removed do not however affect the functioning of the appliance.

WARNING!

Residues from cleaning agents will damage the appliance. Remove residues with water and washing up liquid.

TROUBLESHOOTING

If you are unable to remedy the problem by following the above suggestions, please contact your dealer or the
Customer Care Department.

WARNING!
Repairs to the appliance are only to be carried out by qualified service engineers. Considerable danger to the user may result from improper repairs.

IMPORTANT!
If the appliance has been wrongly operated, the visit from the customer service technician or dealer may not take place free of charge, even during the warranty period.

TECHNICAL DATA

ENVIRONMENT!
Disposal

The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it should be taken to the
appropriate collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential
negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed
information about recycling of this product, please contact your local council, your household waste disposal service or the shop where you purchased the product.

Packaging material

The packaging materials are friendly to the environment and can be recycled. The plastic components are identified by marking: >PE<,>PS<, etc. Discard the
packaging materials as household waste at the waste disposal facilities in your municipality.

INSTALLATION INSTRUCTIONS

WARNING!
This must be read! The laws, ordinances, directives and standards in force in the country of use are to be followed (safety regulations, proper recycling in accordance with the regulations, etc.)

IMPORTANT!
Installation may only be carried out by a qualified electrician. The minimum distances to other appliances and units are to be observed. Anti-shock protection must be provided by the installation, for example drawers may only be installed with a protective floor directly underneath the appliance. The cut surfaces of the worktop are to be protected
against moisture using a suitable sealant. The sealant seals the appliance to the work top with no gap. Do not use silicon sealant between the appliance and the work
top. Avoid installing the appliance next to doors and under windows. Otherwise hot cookware may be knocked off the rings when doors and windows are opened.

WARNING!
Risk of injury from electrical current.

• The electrical mains terminal is live.
• Make electrical mains terminal free of voltage.
• Follow connection schematic.
• Observe electrical safety rules.
• Ensure anti-shock protection by installing correctly.
• The appliance must be connected to the electrical supply by a qualified electrician.
• Loose and inappropriate plug and socket connections can make the terminal overheat.
• Have the clamping connections correctly installed by a qualified electrician.
• Use strain relief clamp on cable.

WARNING!
The surface temperature exceeds 95°C. To avoid a hazard, underbench access must be restricted. Electrical Connection Before connecting, check that the nominal voltage of
the appliance, that is the voltage stated on the rating plate, corresponds to the available supply voltage. Also check the power rating of the appliance and ensure that
the wire is suitably sized in accordance with local wiring rules to suit the appliance power rating. The rating plate is located on the lower casing of the hob. The heating element volt- age is AC230V~. The appliance also works perfectly on networks with AC220V~ or AC240V~. Means for disconnection must be incorporated in the fixed wiring in accordance with local wiring rules. The hob is to be connected to the mains using a device that allows

the appliance to be disconnected from the mains at all poles with a contact opening width of at least 3 mm, eg. automatic line protecting cut-out, earth leakage trips or
fuse. If this appliance’s mains cable is damaged, it must be replaced by a special cable (type H05BB-F Tmax 90°C; or higher). The latter is available from the Customer
Care Department. The connection must be carried out as shown in the diagram. The connecting links should be fitted according to the appropriate connection diagram.
The earth lead is connected to terminal. The earth lead must be longer than leads carrying electric current. The cable connections must be made in accordance
with regulations and the terminal screws tightened securely. Finally, the connecting cable is to be secured with the mains cable cleat and the covering closed by
pressing firmly (lock into place). Before switching on for the first time, any protective foil or stickers must be removed from the glass ceramic surface.

WARNING!
Once connected to the mains supply check that all cooking zones are ready for use by briefly switching each on in turn at the maximum setting.
• A duplicate rating label is supplied with this unit. For easy identification of this unit after installation, stick it to a readily available surface adjacent to the cooktop.

Sticking on the seal

•  Clean the worktop around the cutout area.
• Stick the single-sided adhesive sealing tape provided on the underside of the hob around the outside edgeensuring that it is not stretched. The two ends ofthe tape should join in the middle of one side. After trimming the tape (allow it to overlap by 2-3 mm), press the two ends together.

IMPORTANT!
The cut-out section in the worktop is illustrated in the drawing with the dimensions 560 x 490 / 880 x 490 mm. The appliance can also be built into a
shorter cut-out section with the dimensions 560 x 485 / 880 x 485 mm.

ASSEMBLY

This document sets out the terms and conditions of the product warranties for Electrolux Appliances. It is an important document. Please keep it with your proof of purchase documents in a safe place for future reference should there be a manufacturing defect in your Appliance. This warranty is in addition to other rights you may have
under the Australian Consumer Law.

1. In this warranty:
   (a) ‘ACL’ or ‘Australian Consumer Law’ means Schedule 2 to the Competition and Consumer Act 2010;
   (b) ‘Appliance’ means any Electrolux product purchased by you and accompanied by this document;
   (c) ‘ASC’ means Electrolux’s authorised serviced centres;
   (d) ‘Electrolux’ is the brand controlled by Electrolux Home Products Pty Ltd of 163 O’Riordan Street, Mascot NSW 2020, ABN 51 004 762 341 in respect of Appliances purchased in Australia and Electrolux
   (NZ) Limited (collectively “Electrolux”) of 3-5 Niall Burgess Road, Mount Wellington, in respect of Appliances purchased in New Zealand;
   (e) ‘Warranty Period’ means the period specified in clause 3 of this warranty;
   (f) ‘you’ means the purchaser of the Appliance not having purchased
   the Appliance for re-sale, and ‘your’ has a corresponding meaning.
2.  Application: This warranty only applies to new Appliances, purchased and used in Australia or New Zealand and is in addition to (and does not exclude, restrict, or modify in any way) other rights and remedies under a law to which the Appliances or services relate, including any nonexcludable
   statutory guarantees in Australia and New Zealand.
3. Warranty Period: Subject to these terms and conditions, this warranty continues in Australia for a period of 24 months and in New Zealand for a period of 24 months, following the date of original purchase of the Appliance.
4. Repair or replace warranty: During the Warranty Period, Electrolux or its ASC will, at no extra charge if your Appliance is readily accessible for service, without special equipment and subject to these terms and conditions, repair or replace any parts which it considers to be defective. Electrolux may, in its absolute discretion, choose whether the remedy offered for a valid warranty claim is repair or replacement. Electrolux or its ASC may use refurbished parts to repair your Appliance. You agree that
   any replaced Appliances or parts become the property of Electrolux.
5.  Travel and transportation costs: Subject to clause 7, Electrolux will bear the reasonable cost of transportation, travel and delivery of theAppliance to and from Electrolux or its ASC. Travel and transportation will be arranged by Electrolux as part of any valid warranty claim.
6.  Proof of purchase is required before you can make a claim under this warranty.
7.  Exclusions: You may not make a claim under this warranty unless the defect claimed is due to faulty or defective parts or workmanship. This warranty does not cover:
   (a) light globes, batteries, filters or similar perishable parts;
   (b) parts and Appliances not supplied by Electrolux;
   (c) cosmetic damage which does not affect the operation of the Appliance;
   (d) damage to the Appliance caused by:
   (i) negligence or accident;
   (ii) misuse or abuse, including failure to properly maintain or service;
   (iii) improper, negligent or faulty servicing or repair works done by
   anyone other than an Electrolux authorised repairer or ASC;
   (iv) normal wear and tear;
   (v) power surges, electrical storm damage or incorrect power supply;
   (vi) incomplete or improper installation;
   (vii) incorrect, improper or inappropriate operation;
   (viii) insect or vermin infestation;
   (ix) failure to comply with any additional instructions supplied with
   the Appliance;
   In addition, Electrolux is not liable under this warranty if:
   (a) the Appliance has been, or Electrolux reasonably believes that the
   Appliance has been, used for purposes other than those for which
   the Appliance was intended, including where the Appliance has
   been used for any non-domestic purpose;
   (b) the Appliance is modified without authority from Electrolux in writing;
   (c) the Appliance’s serial number or warranty seal has been removed
   or defaced
8. How to claim under this warranty: To enquire about claiming under
   this warranty, please follow these steps:
   (a) carefully check the operating instructions, user manual and the terms
   of this warranty;
   (b) have the model and serial number of the Appliance available;
   (c) have the proof of purchase (e.g. an invoice) available;
   (d) telephone the numbers shown below.
9. Australia: For Appliances and services provided by Electrolux in Australia: Electrolux goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to
   have the Appliance repaired or replaced if the Appliance fails to be of acceptable quality and the failure does not amount to a major failure. ‘Acceptable quality’ and ‘major failure’ have the same meaning as referred to in the ACL.
10. New Zealand: For Appliances and services provided by Electrolux in New Zealand, the Appliances come with a guarantee by Electrolux pursuant to the provisions of the Consumer Guarantees Act, the Sale of Goods Act and the Fair Trading Act. Where the Appliance was purchased in New Zealand for commercial purposes the Consumer
    Guarantee Act does not apply.
11. Confidentiality: You accept that if you make a warranty claim, Electrolux and its agents including ASC may exchange information in relation to you
    to enable Electrolux to meet its obligations under this warranty.

Important Notice

Read More About This Manual & Download PDF: