Frigidaire Refrigerator User Manual

Refrigerator

All about the
Use &Care
of your Refrigerator

TABLE OF CONTENTS

Important Safety Information………………….2 Features …………………………………………….4 Installation …………………………………………5 Door Removal/Reversal Instructions (some models) …………………………………….7 Door Handle Installation ………………………10 Water Supply Connection ……………………..12 Ice Service………………………………………..14

Controls and Settings ………………………….15 Storage Features ………………………………..16 Normal Operating Sounds …………………….18 Care and Cleaning ………………………………19 Troubleshooting …………………………………21 Limited Warranty………………………………..22

www.frigidaire.com USA 1-800-374-4432

www.frigidaire.ca Canada 1-800-265-8352

A04555604 (July 2019)

IMPORTANT SAFETY INFORMATION

WARNING

Installation Checklist

Please read all instructions before using this refrigerator.
Definitions
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
DANGER
DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING
WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION
CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
IMPORTANT
IMPORTANT indicates installation, operation or maintenance information which is important but not hazard-related.
WARNING
WARNING! CALIFORNIA RESIDENTS Cancer and Reproductive Harm www.P65Warnings.ca.gov
For your Safety
· DO NOT store or use gasoline, or other flammable liquids in the vicinity of this or any other appliance. Read product labels for warnings regarding flammability and other hazards.
· DO NOT operate the refrigerator in the presence of explosive fumes.
· Avoid contact with any moving parts of automatic ice maker.
· Remove all staples from the carton. Staples can cause severe cuts, and also destroy finishes if they come in contact with other appliances or furniture.

Doors Handles are secure and tight Door seals completely to cabinet on all sides Freezer door is level across the top
Leveling Refrigerator is level, side-to-side and
tilted ¼” (6mm) front-to-back Toe grille is properly attached to refrigerator Cabinet is setting solid on all corners
Electrical Power House power turned on Refrigerator plugged in
Ice Maker House water supply connected to refrigerator No water leaks present at all connections
– recheck in 24 hours Ice maker is turned ON Ice & water dispenser operates correctly Front filter must be flush with filter
housing (select models)
Final Checks Shipping material removed Fresh food and freezer temperatures set Crisper humidity controls set Registration card sent in
Child Safety
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Destroy or recycle the carton, plastic bags, and any exterior wrapping material immediately after the refrigerator is unpacked. Children should never use these items to play. Cartons covered with rugs, bedspreads, plastic sheets or stretch wrap may become airtight chambers, and can quickly cause suffocation.
Proper Disposal of your Refrigerator or Freezer
Risk of child entrapment
Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators or freezers are still dangerous ­ even if they will sit for “just a few days”. If you are getting rid of your old refrigerator or freezer, please follow the instructions below to help prevent accidents.

2

IMPORTANT SAFETY INFORMATION

Proper Disposal of Refrigerators/Freezers
We strongly encourage responsible appliance recycling/disposal methods. Check with your utility company or visit www.energystar.gov/recycle for more information on recycling your old refrigerator.
Before you throw away your old refrigerator/ freezer:
· Remove doors.
· Leave shelves in place so children may not easily climb inside.
· Have refrigerant removed by a qualified service technician.
WARNING

IMPORTANT
Turning the Refrigerator controls to “0” will disable your refrigerator’s cooling system, but does not disconnect the power to the light bulb and other electrical components. To turn off power to your refrigerator you must unplug the power cord from the electrical outlet.
Grounding type wall receptacle
Do not, under any circumstances, cut, remove, or bypass the grounding prong.

These guidelines must be followed to ensure that safety mechanisms in this refrigerator will operate properly.
Electrical information
· The refrigerator must be plugged into its own dedicated 115 Volt, 60 Hz., 15 Amp, AC only electrical outlet. The power cord of the appliance is equipped with a threeprong grounding plug for your protection against electrical shock hazards. It must be plugged directly into a properly grounded three prong receptacle. The receptacle must be installed in accordance with local codes and ordinances. Consult a qualified electrician. Avoid connecting refrigerator to a Ground Fault Interrupter (GFI) circuit. Do not use an extension cord or adapter plug.
· If the power cord is damaged, it should be replaced by an authorized service technician to prevent any risk.
· Never unplug the refrigerator by pulling on the power cord. Always grip the plug firmly, and pull straight out from the receptacle to prevent damaging the power cord.
· Unplug the refrigerator before cleaning and before replacing a light bulb to avoid electrical shock.
· Performance may be affected if the voltage varies by 10% or more. Operating the refrigerator with insufficient power can damage the compressor. Such damage is not covered under your warranty.
· Do not plug the unit into an electrical outlet controlled by a wall switch or pull cord to prevent the refrigerator from being turned off accidentally.

Power cord with 3-prong grounded plug
IMPORTANT
CFC/HCFC Disposal Your old refrigerator may have a cooling system that used CFCs or HCFCs (chlorofluorocarbons or hydrochlorofluorocarbons). CFCs and HCFCs are believed to harm stratospheric ozone if released to the atmosphere. Other refrigerants may also cause harm to the environment if released to the atmosphere. If you are throwing away your old refrigerator, make sure the refrigerant is removed for proper disposal by a qualified technician. If you intentionally release refrigerant, you may be subject to fines and imprisonment under provisions of environmental legislation.

3

FEATURES

Features may vary according to model

Ice Maker Ice Bucket Freezer Shelf Auxiliary Freezer
Control Refrigerator
Control
Deli Drawer Cover
Deli Drawer
(Some Models)
Full Shelf

Ice Tray

Fixed Door Bin Door Rack Dairy Door
Upper Door Rack

Deli Drawer Cover
Full Width Deli
(Some Models)
Crisper Cover
Crisper Drawers

Toe Grille

Fixed Door Bin Door Rack

IMPORTANT
Cleaning your Refrigerator
Remove tape and glue residue from surfaces before turning on the refrigerator. Rub a small amount of liquid dish soap over the adhesive with your fingers. Rinse with warm water and dry with a soft cloth.
Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator.
After you remove all of the package materials, clean the inside of your refrigerator before using it. See the “Care & Cleaning” section in this manual.
See important information about cleaning glass shelves and covers in the “Optional Features” section of this manual.

IMPORTANT
Moving your Refrigerator
Your refrigerator is heavy. When moving the refrigerator for cleaning or service, be sure to cover the floor with cardboard or hardboard to avoid floor damage. Always pull the refrigerator straight out when moving it. Do not wiggle or “walk” the refrigerator when trying to move it as floor damage could occur.

4

INSTALLATION

This Use & Care Guide provides general operating instructions for your model. Use the refrigerator only as instructed in this Use & Care Guide. Before starting the refrigerator, follow these important first steps.
Location
· Choose a place that is near a grounded electrical outlet. Do Not use an extension cord or an adapter plug.
· If possible, place the refrigerator out of direct sunlight and away from the range, dishwasher or other heat sources.
· The refrigerator must be installed on a floor that is level and strong enough to support a fully loaded refrigerator.
· Consider water supply availability for models equipped with an automatic ice maker. If you do not hook up water to the refrigerator, remember to turn the ice maker off.

Guidelines for final positioning of your refrigerator:
· All four corners of the cabinet must rest firmly on the floor.
· The cabinet should be level at the front and rear.
· The sides should tilt ¼-inch (6 mm) from front-to-back (to ensure that doors close and seal properly).
· Doors should align with each other and be level.

CAUTION

Do not install the refrigerator where the temperature will drop below 55°F (13°C) or rise above 110°F (43°C). The compressor will not be able to maintain proper temperatures inside the refrigerator.
Do not block the toe grille on the lower front of your refrigerator. Sufficient air circulation is essential for the proper operation of your refrigerator.

NOTE
For additional instructions on garage installation, refer to “Controls” section.

Installation

Installation clearances

· Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections:

Sides & Top

inch

Back

1 inch

NOTE

If your refrigerator is placed with the door hinge side against a wall, you may have to allow additional space for the handle so the door can be opened wider.

5

INSTALLATION
To level the cabinet using the front rollers:
1 Remove the toe grille.

3 Use adjustable wrench to adjust leveling screws. Lower the leveling screws on each side clockwise until they contact the floor (Figure 3). Do not raise the cabinet more than 9/16 inch.

9/16″ (14 mm)
Max

2 Use a flat-blade screwdriver or inch socket wrench to raise or lower the front rollers (Figure 2). Do not raise the cabinet more than 9/16 inch.
Raise

Raise
Figure 3
NOTE
Raise the front of the refrigerator enough so the doors close freely when opened halfway. The refrigerator should slope ¼ inch to ½ inch from front-to-back. Then level the refrigerator from side-to-side.

9/16″ (14 mm)
Max

Figure 2 or

6

DOOR REMOVAL/REVERSAL INSTRUCTIONS
(SOME MODELS)

Tools Necessary:

or

PhillipsTM Head

Socket Wrench Set

Adjustable Wrench

or
3/8″ (10mm) Fixed Wrench

Top Hinge Cover Front
Screw

Top Hinge Cover Rear
Screw

Top Hinge Screw

Bottom Hinge Screw

Door removal and reversal
instructions:
1. Remove toe grille.
2. Remove top hinge cover. Trace around the hinge with a soft lead pencil. This makes reinstallation easier. Remove top hinge and lift door off center hinge pin. Set door aside.

NOTE
The direction in which your refrigerator doors open (door swing) can be reversed, from left to right or right to left, by moving the door hinges from one side to the other. Reversing the door swing should be performed by a qualified person.
IMPORTANT
Before you begin, turn the refrigerator temperature control to “0” and remove the electrical power cord from the wall outlet. Remove any food from door shelves.

Door Stop Screw

Door Stop
Washer Shim Hinge
Pin Center Hinge

Top Hinge Cover

Hinge Hole Plug

Screws
Handle Hole Plug

Top Hinge

7. Remove two screws on bottom hinge with ” socket wrench.
8. Install bottom hinge on opposite side with the two screws removed from step 7.

3. Unscrew center hinge pin using adjustable wrench and save for reassembly. Ensure plastic washer stays on hinge pin.
4. Lift refrigerator door off of bottom hinge and set aside.
5. Remove center hinge and shim by removing inside screw and loosening two outside screws enough to allow hinge and shim to slide out. Tighten screws.
6. Loosen two outside screws on opposite side of refrigerator, remove inside screw and install center hinge.

Door Stop Screw

Door Stop

Washer

Hinge Pin

Bottom Hinge Screws

Toe Grille
7

DOOR REMOVAL/REVERSAL INSTRUCTIONS
(SOME MODELS)

9. Unscrew bottom hinge pin using adjustable wrench. Move hinge pin to other hole in hinge and tighten with adjustable wrench.
10. Reverse door handles (see instruction on next page).
11. Move freezer and refrigerator door stops to opposite side. Before starting screws, use an awl to puncture the foam.
12. Position refrigerator door onto bottom hinge pin and screw center hinge pin through center hinge into top of door. Close refrigerator door to help align hinge hole.
13. Tighten center hinge pin with adjustable wrench.
14. Remove cabinet and hinge hole plugs and move to opposite side.
15. Lower freezer door onto center hinge pin.
16. Close freezer door. Lift up on handle side of door and grasp the thinnest part of the top hinge cover (which was removed in Step 2) and insert the thickest part between the doors on the handle side approximately 3 inches from the outside edge. This will ensure proper spacing.

17. Tighten the top hinge screws and check door gasket for open seal condition (gap between gasket and cabinet flange).
Look for open areas between the gasket and the cabinet flange.

Gasket should seal against the cabinet all the way around including top
and bottom

8

DOOR REMOVAL/REVERSAL INSTRUCTIONS
(SOME MODELS)
18. Should open seal condition exist, try to massage the gasket to make sure it is seated into the channel.
IMPORTANT
If the condition still exists, try heating the gasket with a hair dryer with the door closed. Use Caution and be careful not to damage the interior door panel or gasket by applying too much heat. 19. If the open seal condition still exists, it
may be necessary to flip the gasket. In this case, remove the gasket from the door by pulling it out. Rotate the gasket half a turn (180 degrees). Reinstall the gasket by inserting the corners first then work towards the middle assuring that it is fully seated in the channel. 20. Flip toe grille and reinstall. 21. Plug in electrical power cord and turn refrigerator temperature control to center position. Adjust setting as necessary.
9

DOOR HANDLE INSTALLATION

CAUTION
Wear gloves and use extreme CAUTION when installing these handles. The rounded end of the handles may be sharp.

2. Install the two screws into the bottom of the handle.
3. Tighten the set screw on the rounded part of the handle until the handle is flush with the door, then tighten another ½ turn.

IMPORTANT
To ensure proper installation of handles, please review these instructions and illustrations thoroughly prior to installing the handles.
Additionally, before installing the door handles, make sure the door swing is correct. Your model will have either a right hand or left hand door swing. Follow instructions in the Use & Care Guide to reverse the doors, if necessary.

Shoulder Screw
Set Screw Nameplate

To attach metal refrigerator handle:
1. Place rounded part of handle onto shoulder screw on face of door and align the two holes in top of handle with the two holes in top of door. Do not tighten the set screw yet.
2. Install the two screws into the top of the handle.
3. Tighten the set screw on the rounded part of the handle until the handle is flush with the door, then tighten another ½ turn.

Screw

Handle

Stainless Steel Models

Screw Handle

Shoulder Screw

Screw

Handle

Set Screw

Button Plug

Shoulder Screw

Set Screw

Shoulder Screw
Set Screw

To attach metal freezer handle:
1. Place rounded part of handle onto shoulder screw on face of door and align the two holes in bottom of handle with the two holes in bottom of door. Do not tighten the set screw yet.
10

Handle Screw

DOOR HANDLE INSTALLATION

To reverse metal refrigerator/freezer handles:
Handles may be easier to reverse while doors are off. Reverse freezer and refrigerator handles as shown.

To attach plastic refrigerator handle:
1. With the door open, place the end of the handle on the dove tail mounting screw and pull down to secure in place.
2. Align handle base with holes in top of door.
3. Install screws packaged with the handle.

Screws Los tornillos
Vis

Handle Base Base de mango Base de poignée

CAUTION
Be sure doors are set aside in a secure position where they cannot fall and cause personal injury.
CAUTION
Do not use an electric screwdriver to attach handles; overtightening handles may crack them. Use a handheld screwdriver only.

Handle Manija Poignée
To attach plastic freezer handle: 1. With the door open, place the end of the
handle on the dove tail mounting screw and push up to secure in place. 2. Align handle base with holes in bottom of door. 3. Install screws packaged with the handle.

Mounting Screw

Handle

These screws are packaged
with the handles.

Screws Handle Base
11

WATER SUPPLY CONNECTION

WARNING
To avoid electric shock, which can cause death or severe personal injury, disconnect the refrigerator from electrical power before connecting a water supply line to the refrigerator.
CAUTION
To Avoid Property Damage:
· Copper or Stainless Steel braided tubing is recommended for the water supply line. Water supply tubing made of ¼ inch plastic is not recommended to be used. Plastic tubing greatly increases the potential for water leaks, and the manufacturer will not be responsible for any damage if plastic tubing is used for the supply line.
· DO NOT install water supply tubing in areas where temperatures fall below freezing.
· Chemicals from a malfunctioning softener can damage the ice maker. If the ice maker is connected to soft water, ensure that the softener is maintained and working properly.
IMPORTANT
Ensure that your water supply line connections comply with all local plumbing codes.

Before Installing The Water Supply Line, You Will Need:
· Basic Tools: adjustable wrench, flat-blade screwdriver, and PhillipsTM screwdriver
· Access to a household cold water line with water pressure between 30 and 100 psi.
· A water supply line made of ¼ inch (6.4 mm) OD, copper or stainless steel tubing. To determine the length of tubing needed, measure the distance from the ice maker inlet valve at the back of the refrigerator to your cold water pipe. Then add approximately 7 feet (2.1 meters), so the refrigerator can be moved out for cleaning (as shown).
· A shutoff valve to connect the water supply line to your household water system. DO NOT use a self-piercing type shutoff valve.
· Do not re-use compression fitting or use thread seal tape.
· A compression nut and ferrule (sleeve) for connecting a copper water supply line to the ice maker inlet valve.
NOTE
Check with your local building authority for recommendations on water lines and associated materials prior to installing your new refrigerator. Depending on your local/ state building codes, Frigidaire recommends for homes with existing valves its Smart Choice® water line kit 5305513409 (with a 6 ft. Stainless Steel Water Line) and for homes without an existing valve, Frigidaire recommends its Smart Choice® water line kit 5305510264 (with a 20 ft. Copper Water Line with self-tapping saddle valve). Please refer to www.frigidaire.com/store for more information.

12

WATER SUPPLY CONNECTION

To Connect Water Supply Line To Ice Maker Inlet Valve
1. Disconnect refrigerator from electric power source.
2. Place end of water supply line into sink or bucket. Turn ON water supply and flush supply line until water is clear. Turn OFF water supply at shutoff valve.
3. Remove plastic cap from water valve inlet and discard cap.
4. If you use copper tubing – Slide brass compression nut, then ferrule (sleeve) onto water supply line. Push water supply line into water valve inlet as far as it will go (¼ inch / 6.4 mm). Slide ferrule (sleeve) into valve inlet and finger tighten compression nut onto valve. Tighten another half turn with a wrench; DO NOT over tighten. See Figure 1.
If you use braided flexible stainless steel tubing – The nut is already assembled on the tubing. Slide nut onto valve inlet and finger tighten nut onto valve. Tighten another half turn with a wrench; DO NOT over tighten. See Figure 2.
5. With steel clamp and screw, secure water supply line (copper tubing only) to rear panel of refrigerator as shown.
6. Coil excess water supply line (copper tubing only), about 2½ turns, behind refrigerator as shown and arrange coils so they do not vibrate or wear against any other surface.
7. Turn ON water supply at shutoff valve and tighten any connections that leak.
8. Reconnect refrigerator to electrical power source.
9. To turn ice maker on, lower wire signal arm (side mounted) or set the ice maker’s On/Off power switch to the “I” position (rear mounted).
NOTE
These instructions do not cover after market ice maker installation. Instructions in after market ice maker kit should be used.

Plastic Water Tubing to Ice Maker Fill Tube

Steel Clamp Brass Compression
Nut Ferrule (Sleeve)
Copper water line

Water Valve Bracket
Valve Inlet

Water Valve Copper water line
from household water supply

(Include enough tubing in loop to allow moving refrigerator out for cleaning.) Figure 1

Plastic Water Tubing to Ice Maker Fill Tube

Steel Clamp

Braided Flexible Stainless
Steel Water Line Water Valve
Bracket Valve Inlet

Water Valve

6 ft (1.8 Meters) Braided flexible stainless steel water line from household water supply.
(Include enough tubing in loop to allow moving refrigerator out for cleaning.) Figure 2

13

ICE SERVICE

If your refrigerator has an automatic ice maker, minimal ice will be produced during the first 24 hours of operation. Air in new plumbing lines may cause the ice maker to cycle two or three times before making a full tray of ice. With no usage, it will take approximately one to two days to fill the ice container.
New plumbing connections may cause the first production of ice cubes to be discolored or have an odd flavor. Discard ice made during the first 24 hours.

IMPORTANT
Your ice maker is shipped from the factory with the wire signal arm in the ON position. To ensure proper function for your ice maker, hook up water supply immediately or turn ice maker OFF by lifting the wire signal arm until it clicks and locks in the UP position. If the ice maker is on and the water supply is not connected, the water valve will make a loud chattering noise.

NOTE
Automatic ice makers are also optional accessories that may be installed in most models at any time. Call your local dealer for information.
Turning your Ice Maker On
After the plumbing connections have been completed, the water supply valve must be opened. Place the ice container under the ice maker, pushing it as far back as possible. Lower the wire signal arm to its “down” or ON position.

ICE PRODUCTION: WHAT TO EXPECT
The ice maker will produce 2.5 to 3 pounds of ice every 24 hours depending on usage conditions. Ice is produced at a rate of 8 cubes every 80 to 160 minutes.
CAUTION
Do Not place the ice container in your dishwasher.

Turning your Ice Maker Off
To stop the ice maker, lift the wire signal arm until it clicks and locks in the “up” or OFF position. The ice maker also turns off automatically when the ice container is full.

ON

OFF
Wire Signal Arm

14

CONTROLS AND SETTINGS

Cool Down Period
To ensure safe food storage, allow the refrigerator to operate with the doors closed for at least 8 hours before loading it with food.
Refrigerator & Freezer Controls
NOTE
When first turning refrigerator on, adjust control to recommended. This is the recommended initial setting. After 24 hours, adjust the controls as needed.
Allow 24 hrs for adjustments

CAUTION
Do not install the refrigerator where the temperature will drop below 55°F (13°C) or rise above 110°F (43°C). The compressor will not be able to maintain proper temperatures inside the refrigerator.
IMPORTANT
If you install your refrigerator in a garage or other unheated area, you may experience freezer temperature problems during the winter months when temperatures dip below 55° F. Upgrading your refrigerator with a Garage Kit will lower the minimum operating temperature of your unit to 34° F. This kit can be ordered by calling the phone number listed at the bottom of the warranty page or back cover at an additional cost.

Refrigerator Control
IMPORTANT
Adjusting the refrigerator temperature control to “0” turns off the compressor and prevents the refrigerator from cooling, but does not disconnect the power to the light bulb and other electrical components. To turn off power to your refrigerator, you must unplug the power cord from the wall outlet.
Temperature Adjustment
· Adjust temperature gradually: adjust the knob in small increments, allowing the temperature to stabilize.
· For colder temperatures, adjust the knob towards coldest.
· For warmer temperatures, adjust the knob towards cold.
Adjusting the refrigerator control will change temperatures in both compartments. The auxiliary freezer control can be left at the factory pre-set (mid position) or adjusted as desired; it has no effect on electrical power to the refrigerator. To maintain temperatures, a fan circulates air in the refrigerator and freezer compartments. For good circulation, do not block cold air vents with food items.

Auxiliary Freezer Control 15

STORAGE FEATURES

CAUTION
Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. Tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping.

CAUTION
To avoid personal injury or property damage, handle tempered glass shelves carefully. Shelves may break suddenly if nicked, scratched, or exposed to sudden temperature change.
Shelf Adjustment
Refrigerator shelves are easily adjusted to suit individual needs. Before adjusting the shelves, remove all food.
To adjust sliding shelves:
1. Remove shelf by pulling forward to stop position.
2. Lift front edge up and pull out.
To replace shelf, rest side edges on any pair of shelf rails and carefully push shelf back into position.

Sliding Wire Shelf
Door storage
Door bins, shelves, and racks are provided for convenient storage of jars, bottles, and cans. Frequently used items can be quickly selected. The dairy compartment, which is warmer than the general food storage section, is intended for short term storage of cheese, spreads, or butter.
Door rack
Some models have door racks or bins that can accommodate gallon-sized plastic drink containers and economy-sized jars and containers. To remove door rack:
1. Push on rack sides to release from locking tabs. 2. Pull straight out. To install door rack: 1. Push rack straight ahead. 2. You will hear the sides lock into the tabs.

Sliding Glass Shelf
16

Door Rack

STORAGE FEATURES

Crisper Humidity Control (some models)
The crisper humidity control, present on the crisper drawers of some models, allows you to adjust the humidity within the crisper. This can extend the life of fresh vegetables that keep best in high humidity.

Crispers (some models)
The crispers, located under the bottom refrigerator shelf, are designed for storing fruits, vegetables, and other fresh produce. Wash items in clear water and remove excess water before placing them in the crispers. Items with strong odors or high moisture content should be wrapped before storing.

Low Humidity

High Humidity

Higher Humidity Lower Humidity
NOTE
Leafy vegetables keep best when stored with the Humidity Control set on High Humidity, or in a drawer without a Humidity Control. This keeps incoming air to a minimum and maintains maximum moisture content. Store non-leafy vegetables and fruits still in their skins at the low humidity setting.

17

NORMAL OPERATING SOUNDS

Understanding the sounds you may hear
Your new, high-efficiency refrigerator may introduce unfamiliar sounds. These sounds normally indicate your refrigerator is operating correctly. Some surfaces on floors, walls, and kitchen cabinets may make these sounds more noticeable.
NOTE
Rigid foam insulation is very energy efficient, but is not a sound insulator.

Following is a list of major components in your refrigerator and the sounds they can cause:
A Evaporator Refrigerant through the evaporator may create a boiling or gurgling sound.
B Evaporator fan You may hear air being forced through the refrigerator by the evaporator fan.
C Defrost heater During defrost cycles, water dripping onto the defrost heater may cause a hissing or sizzling sound. After defrosting, a popping sound may occur.
IMPORTANT
During the automatic defrost cycle, you may notice a red glow in the vents on the back wall of your freezer compartment. This is normal during the defrost cycle.

D Automatic ice maker When ice has been produced, you will hear ice cubes falling into the ice bin.
E Automatic Defrost control These parts can produce a snapping or clicking sound when turning the cooling system on and off.
F Condenser fan You may hear air being forced through the condenser.
G Compressor Modern, high-efficiency compressors run much faster than in the past. The compressor may have a highpitched hum or pulsating sound.
H Water valve If your refrigerator is equipped with an automatic ice maker, you will hear a buzzing sound as the water valve opens to fill the ice maker during each cycle.
I Drain pan (not removable) You may hear water dripping into the drain pan during the defrost cycle.
J Condenser May create minimal sounds from forced air.

18

CARE AND CLEANING

Protecting your investment
Keeping your refrigerator clean maintains appearance and prevents odor build-up. Wipe up any spills immediately and clean the freezer and fresh food compartments at least twice a year. When cleaning, take the following precautions:
· Never use CHLORIDE or cleaners with bleach to clean stainless steel.
· Do not wash any removable parts in a dishwasher.
· Always unplug the electrical power cord from the wall outlet before cleaning.
· Remove adhesive labels by hand. Do not use razor blades or other sharp instruments which can scratch the appliance surface.
· Do not remove the serial plate.
Do not use abrasive cleaners such as window sprays, scouring cleansers, brushes, flammable fluids, cleaning waxes, concentrated detergents, bleaches or cleansers containing petroleum products on plastic parts, interior doors, gaskets or cabinet liners. Do not use paper towels, metallic scouring pads, or other abrasive cleaning materials or strong alkaline solutions.

IMPORTANT
If you store or move your refrigerator in freezing temperatures, be sure to completely drain the water supply system. Failure to do so could result in water leaks when the refrigerator is put back into service. Contact a service representative to perform this operation.

NOTE
If you set your temperature controls to turn off cooling, power to lights and other electrical components will continue until you unplug the power cord from the wall outlet.

CAUTION
· Pull the refrigerator straight out to move it. Shifting it from side to side may damage flooring. Be careful not to move the refrigerator beyond the plumbing connections.
· Damp objects stick to cold metal surfaces. Do not touch refrigerated surfaces with wet or damp hands.

19

CARE AND CLEANING

Part
Interior & Door Liners
Door Gaskets Drawers & Bins Glass Shelves
Toe Grille
Exterior & Handles
Exterior & Handles (Stainless Steel Models Only)
Replacing Light Bulbs

Care & Cleaning Tips

What To Use

Tips and Precautions

· Soap and water
· Baking soda and water

Use 2 tablespoons of baking soda in 1 quart of warm water. Be sure to wring excess water out of sponge or cloth before cleaning around controls, light bulb or any electrical part.

· Soap and water

Wipe gaskets with a clean soft cloth.

· Soap and water

Use a soft cloth to clean drawer runners and tracks.

· Soap and water · Glass cleaner · Mild liquid sprays · Soap and water · Mild liquid sprays · Vacuum attachment · Soap and water · Non Abrasive Glass
Cleaner
· Soap and water · Stainless Steel
Cleaners
· Unplug refrigerator · Wear gloves · Remove light cover
(some models) · Replace old bulb · Replace light cover
(some models) · Plug in the
refrigerator

Allow glass to warm to room temperature before immersing in warm water.
Vacuum dust from front of toe grille. Remove toe grille (see Installation Instructions). Vacuum backside, wipe with sudsy cloth or sponge. Rinse and dry.
Do not use commercial household cleaners containing ammonia, bleach or alcohol to clean handles. Use a soft cloth to clean smooth handles. DO NOT use a dry cloth to clean smooth doors.
Never use CHLORIDE or cleaners with bleach to clean stainless steel.
Clean stainless steel front and handles with nonabrasive soapy water and a dishcloth. Rinse with clean water and a soft cloth. Use a non-abrasive stainless steel cleaner. These cleaners can be purchased at most home improvement or major department stores. Always follow manufacturer’s instructions. Do not use household cleaners containing ammonia or bleach.
NOTE: Always clean, wipe and dry with the grain to prevent scratching. Wash the rest of the cabinet with warm water and mild liquid detergent. Rinse well, and wipe dry with a clean soft cloth.
CAUTION: Wear gloves when replacing light bulbs to avoid getting cut. Use same wattage when replacing bulb

20

TROUBLESHOOTING

1-800-374-4432 (United States) 1-800-265-8352 (Canada)

Visit our web site at www.frigidaire.com.

Common Occurrences

Before calling for service, review this list. It may save you time and expense. This list includes common occurrences that are not the result of defective workmanship or materials in this appliance.

Refrigerator does not run.

· Ensure plug is tightly pushed into electrical outlet.
· Check/replace fuse with a 15 amp time-delay fuse. Reset circuit breaker.
· The refrigerator/freezer control is turned to “0”

· Refrigerator may be in defrost cycle. Wait 20 minutes and check again.

Freezer temperature is colder than preferred. Refrigerator temperature is satisfactory.

· Set auxiliary freezer control to a warmer setting until freezer temperature is satisfactory. Allow 24 hours for the temperature to stabilize.

Refrigerator temperature is too · Set refrigerator/freezer control to a warmer setting. Allow

cold. Freezer temperature is

24 hours for temperature to stabilize. Then check freezer

satisfactory.

temperatures and adjust as needed.

Freezer temperature is warmer than preferred. Refrigerator temperature is satisfactory.

· Set auxiliary freezer control to a colder setting until freezer temperature is satisfactory. Allow 24 hours for the temperature to stabilize.

Refrigerator temperature is too · Set refrigerator/freezer control to a colder setting.

warm. Freezer temperature is

Allow 24 hours for temperature to stabilize. Then check

satisfactory.

refrigerator temperatures and adjust as needed.

Refrigerator is noisy or vibrates. · The cabinet is not level. · Floor is weak.

· See Normal Operating Sounds and Sights section.

Odors in refrigerator.

· Interior needs to be cleaned.

· Foods that produce odors should be covered or wrapped.

Cabinet light not working.

· Replace light bulb.

· Ensure plug is tightly pushed into electrical outlet.

· Light switch may be stuck. Push in light switch, located on the refrigerator control box, to release.

Automatic ice maker not working (some models)

· Ensure the wire signal arm is not in UP position.
· Ice maker should produce 2.5 to 3 pounds of ice in a 24 hour period.

· Water supply is turned off. · Water pressure is too low.

· The freezer is not cold enough.

21

LIMITED WARRANTY

Your appliance is covered by a one year limited warranty. For one year from your original date of purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed, used and maintained in accordance with the provided instructions.
Exclusions This warranty does not cover the following:
1. Products with original serial numbers that have been removed, altered or cannot be readily determined. 2. Product that has been transferred from its original owner to another party or removed outside
the USA or Canada. 3. Rust on the interior or exterior of the unit. 4. Products purchased “as-is” are not covered by this warranty. 5. Food loss due to any refrigerator or freezer failures. 6. Products used in a commercial setting. 7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances
not in ordinary household use or used other than in accordance with the provided instructions. 8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance. 9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards,
shelves, etc., which are not a part of the appliance when it is shipped from the factory. 10. Service calls to repair or replace appliance light bulbs, air filters, water filters, other
consumables, or knobs, handles, or other cosmetic parts. 11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry
trip charges, or mileage expense for service calls to remote areas, including the state of Alaska. 12. Damages to the finish of appliance or home incurred during installation, including but not
limited to floors, cabinets, walls, etc. 13. Damages caused by: services performed by unauthorized service companies; use of parts other than
genuine Electrolux parts or parts obtained from persons other than authorized service companies; or external causes such as abuse, misuse, inadequate power supply, accidents, fires, or acts of God.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR. ELECTROLUX SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.
If You Need Service
Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period should service be required. If service is performed, it is in your best interest to obtain and keep all receipts. Service under this warranty must be obtained by contacting Electrolux at the addresses or phone numbers below.
This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances North America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by Electrolux Canada Corp. Electrolux authorizes no person to change or add to any obligations under this warranty. Obligations for service and parts under this warranty must be performed by Electrolux or an authorized service company. Product features or specifications as described or illustrated are subject to change without notice.

USA 1.800.374.4432 Frigidaire 10200 David Taylor Drive Charlotte, NC 28262

Canada 1.800.265.8352 Electrolux Canada Corp. 5855 Terry Fox Way Mississauga, Ontario, Canada
L5V 3E4

22