Sharp Full Automatic Washing Machine Instruction Manual

  SHARP Full Automatic Washing Machine Instruction Manual

S-W110DS
ES-W100DS

Safety precautions

WARNING

  • Do not allow children to play with or look around the washing / spin drying tub, in case of injury.

    FORBIDDEN
  • Clothing stained with harmful diluting agents such as gasoline, kerosene and so on must not be put into the washing / spin drying tub.

    FORBIDDEN

    INFLAMMABLES GASOLINE
  • Do not use power supply other than AC220-240V, 50Hz, so as to avoid malfunction, damage and fire.

    FORBIDDEN
    DISASSEMBLE
  • Do not place the machine at high-humidity places such as bathroom, locations where wind and rain may get in, and so on. Otherwise, electric shock, fire, malfunctions and distortion may take place.

    FORBIDDEN TO USE AT HIGH-HUMIDITY LOCATIONS 
  • Use plug socket above 13A separately. A loose plug socket or the action of sharing a plug socket with other apparatus may start a fire due to heat.

    MANDATORY
  • While cleaning the machine body, the plug should be pulled out first. Do not plug or pull the plug with wet hand or wet cloth, so as to avoid electric shock.

    PLUG OR PULL THE PLUG
  • Before the washing / spin drying tub completely stops, do not touch the clothing being washed. Even if the tub is running at low speed, your hand may get wrapped up and injured. Special attention should be paid to children.

    FORBIDDEN TO TOUCH
  • Do not change the original state of power cable. Any artificial damage to the power cable could cause electric shock, electric leakage or other malfunctions.

    FORBIDDEN
  • Do not use damaged power cable, plug and loose plug socket, so as to avoid short circuit, electric shock, fire and other accidents.

    FORBIDDEN
  • Do not use water to wash components of the machine, so as to avoid short circuit and electric shock.

    FORBIDDEN TO WASH WITH WATER
  • Do not approach any fire source to a plastic component, which has the risk of starting a fire.

    FORBIDDEN
  • Clean the dust on the plug and plug socket to avoid fire.

    MANDATORY

Specification

Model

ES-W110DS

ES-W100DS

Power supply

220V-240V ~ 50Hz

Standard washing/ spin drying capacity

11.0 kg

10.0 kg

Standard water consumption

95 L

93 L

Standard water Level

51 L

48 L

Washing / Spin Drying Rated Power Input

610 W / 310 W

605 W / 360 W

Washing type 

Swirl type

Water pressure

0.03 ~ 0.8 MPa

Weight

37 kg

Dimensions (W×D×H (mm)) 

580 × 625 × 1031

580 × 625 × 1011

Common non-fault phenomenon

Phenomenon

Check

Not working Light cannot be on
  • Is the plug plugged in firmly?
  • Is the power supply interrupted or does the main switch in your house trip off?

There’s abnormal sound.
  • Does the washing machine incline or is it unstable?
  • Does the clothing  deviate to one side during spin drying?
  • Is there a hair clip or other foreign metal objects mixed in the clothing?

No water inlet

There’s no water supply if the top cover is open. Please close the top cover properly

Tap leaks
  • Are the screws or the installation position of the water nozzle connection loose?
  • Does the water nozzle connection incline or shake?

 

Inspection of a washing machine that have been used for many years. 

Check

Are there situations like these?

  • Doesn’t operate sometimes.
  • “CHILD LOCK” doesn’t work during operation.
  • Water leakage (water hose, spinning tub, tap connection).
  • There is burning smell.
  • There is an abnormal sound or vibration during operation
  • Your hand feels numb while touching the machine.
  • Power cable or plug is unusually hot.

Stop using the machine

To avoid a fault y or an accident, please pull out the plug from the plug socket. Be sure to entrust the maintenance department to check it, and consult the maintenance department for check and repair fees.

Safety precautions

WARNING

  • Do not wash water resistant clothing. Do not wash sleeping bags, bath curtains, raincoats, rain ponchos, rain covers, ski jackets, ski pants, automobile covers and other water resistant clothing, so as to avoid abnormal vibration and other unexpected accidents.

    FORBIDDEN

    DO NOT PUTWATER-RESISTANT CLOTHING INTO THE TUB
    CUATION
     During spin drying, the washing machine is rotating at high speed. Because water in water resistant clothing could not be discharged instantaneously, the machine will be out of balance, causing abnormal vibration and other unexpected accidents.
  • Do not wash objects other than clothing to avoid abnormal vibration that causes damage to machine.

    FORBIDDEN
  • The temperature of water must not exceed 50℃, so as to avoid accidents of electric leakage and electric shock due to distortion or damage of plastic.

    FORBIDDEN
  • While pulling out or plugging the plug, do not touch the metal part of the plug, so as to avoid electric shock or short circuit.

    MANDATORY
  • After using the washing machine, please pull out the plug, so as to avoid electric leakage, electric shock or fire due to loose connection of plug.

    PLUG OR PULL
    OUT THE PLUG
  • Before using, check carefully if the connection of water inlet hose or drain hose is reliable, so as to avoid water leakage.

    MANDATORY
  • When the machine is running, do not touch the bottom with hand or foot, where there’s a rotating mechanism, so as to avoid getting hurt.

    FORBIDDEN TO TOUCH
  • Before using, check the bottom of the product, make sure there is no packaging material such as a plastic holder attaching on visual parts. And then install the bottom cover.

    MANDATORY
  • Do not put heavy objects on the machine. so as to avoid distortion and damage.

    FORBIDDEN
  • After using, please turn off the tap to avoid water leakage.
  • The base opening must not be obstructed by carpeting when the washing machine is installed on a carpeted floor.

    MANDATORY
    CUATION
  • To avoid danger, if the soft power cable is damage, it must be replaced by the manufacture or its maintenance department or similar dedicated personnel.
  • If powder detergent or liquid detergent adheres to a plastic component such as the top cover, wipe it away immediately, otherwise it may damage the plastic component. Safety precautions
  • Each time washing is finished, clean lint filter box. Otherwise it may not have effect to trap lint.

Common non-fault phenomenon

Phenomenon

Not a fault

Water inlet

A sound in water hose and water inlet valve.

A sound in water hose and water inlet valve.

Washing

Rinsing

When washing or rinsing is finished,
the pulsator will rotate slightly.

To avoid the offset of clothing to reduce vibration during spin drying.

During the washing process,the pulsator rotates discontinuously.

In the soaking and washing in soak course, the pulsator rotates once every 8 seconds, so that the detergent can permeate into the clothing sufficiently.

Spinning

When spinning starts, low-speed rotation will happen for a while. (Do not rotate at high speed immediately.)

This action is done to adjust the balance and to dry clothing sufficiently.

When spinning starts, the machine gives off sounds like “Patsa Patsa”.

During spin drying, water hits the tub side, which is not abnormal.

During spinning, the program inlets water and enters rinsing. (Spin light indicator blinks quickly.)

During the rotation in spin drying, the offset of clothing is detected and corrected automatically. (If the offset phenomenon cannot be changed by auto-correction, the operation will stop immediately.)

The clothing has been spin dried but not wringed dry.

The spin drying ratio of an automatic washing machine is a little lower than that of a twin tub washing machine. In case the spin drying of large clothing such as towels, blankets etc. is uneven, please spin drying it again.

Others

Operating parts heat up.

It’s caused by the heat radiation of electrical components

Indoor lighting darkens in an instant.

The voltage of plug loop in your house drops in an instant when the motor starts up. (Please use an exclusive plug loop.)

There’s a sound of water when tub body is rotated To keep balance during spinning, there’s liquid in the balance ring
There’s a stray noise on the radio or television, and the image is unclear. Keep away from radio and television as far as possible.
After washing is finished, there are white lines around the washing / spin drying tub. The white powdery material is the result of the combination of ingredients in detergent and ingredients in water (Wipe away with twisted cloth.) Please note that it will stick on where it is left. Using liquid detergent or injecting water and rinsing twice can prevent this phenomenon.

Name of each component

Machine body

List of accessories

Name

Quantity

Water inlet hose assembly

 1 set
Drain hose

1

Screw ※

 1
Bottom cover ※

1

Operation manual

 1
Installation manual

1

※ Bottom Cover and Screw are applied by Service staff. Caution

Common non-fault phenomenon (Please refer to this section if there is an abnormality happens.)

Abnormal display

CUATION

It generates a beep when washing machine indicates abnormal display. If not connected in 10 min, it turns off automatically.
Because the phenomenon may not be a fault, please check it again before sending the machine for repair. In the case of failure, please consult the maintenance department. Be sure not to disassemble and repair the machine without permission.

Presentation

 Possible non-fault cause Coping process

Failure cause

  • Low flow at the faucet.
  • The faucet is closed.
  • Water inlet filter net is blocked.
  • Increase water supply, press START / PAUS key.
  • Turn the faucet on, press START/PAUSE key.
  • Clean filter net, press START/PAUSE key.
  • Top cover is opened as the reservation course starts.
  • Top cover is not closed during spin drying.
  • Close top cover.

  • The drain position is relatively high.
  • The end of drain hose is blocked.
  • Drain hose is folded/ crumpled/tied.
  • Adjust drain hose properly, press START /PAUSE key.
  • Clean drain hose, press START/PAUSE key.
  • Washing machine inclines or shaky.
  • The clothing is lopsided.
  • Place washing machine place the horizontally by adjusting the foot.
  • Distribute the clothing evenly.
  • Water level sensor shows an abnormal level.
  • Pull out the plug from the plug seat, and entrust the maintenance department.
  • Top cover opened in the situation of CHILD LOCK
  • Turn off the power off, and take it from the top.
    CUATION
    CHILD LOCK is not released, unless you reset it manually.

–

Maintenance

TUB CLEAN

CUATION

  • Do not put the clothing in the tub in this course.
  1. Press Power ON/OFF key with the top cover closed.
  2. Press COURSE key, and select TUB CLEAN course.

    Press WASH key, and select the washing time. Press WATER LEVEL key, and select the water level as necessary.
     
  3. Press START/PAUSE key.

    The washing machine starts to supply water, and displays remaining operation time.
  4. The machine generates a beep when it finishes supplying water.
    Press START/PAUSE key, and the washing machine pauses.

    Put the washing machine cleaner for washing the tub.
  5. Close the top cover and press START/PAUSE key to restart.

Key points of washing

Pay more attention to the following situations

  • Before washing, please remove sludge and sand on clothing first.
  • For very dirty parts of the clothes, you can smear some liquid detergent on them and rub them in advance.
  • For clothing that are easy to pill, please turn it inside out first and then wash it.
  • Large clothing and clothing that are easy to float should be put into the washing tub first.
    Please put large clothing and clothing that are easy to float (chemical fibers etc.) at the bottom. This is beneficial to the good rotation of clothing.

To avoid damage to tub, pulsator…

  • Please take out coin, hair clip, curtain hook and other metal.
  • Wrap up buttons and zipper and put them on the inner side.
  • Put bra etc. in washing mesh bag.

To avoid damage to clothing, winding of clothing…

  • Belts on apron and so on must be knotted; zippers must be zipped.
  • Thin or easily damaged clothing must be washed in washing mesh bag.
  • Metal decorations (zippers etc.) on the clothing in washing mesh bag must be checked.

For better washing… 

  • Please check the washing mark.
  • Wash clothing easy to fade separately.
  • For towels and other clothing easy to produce lints, please wash them separately or use washing mesh bag.

To protect the environment
.To avoid the waste of water, detergent and electricity.

  • During washing, wash clothing together.
  • Put in proper amount of detergent according to the fouling situation.
  • Reuse detergent liquid.

While using a washing mesh bag, put in as little clothing as possible. Too much clothing will decrease the performance during rinsing and spin drying or cause the offset of clothing during spin drying.

Instruction on control panel functions

Control panel / Display

 POWER: Plug the machine in and then press this key, the machine turns on. Press this key again, it turns off.

CUATION

  1. If the machine is energized but not started, the power supply turns off automatically 5 min later.
  2. If no key pressed after the START/PAUSE key is pressed during the operation, the power supply turns off automatically 10 min later.

START/PAUSE: Press this key after turning on, selected course is started. Press this key again, the running is paused. Press it once again, the running restarts.

 NORMAL: Wash daily clothing like relatively-dirty shirts or pants.
JEANS: Wash heavy and very dirty clothing.

SPEEDY: Wash speedy for not-so-dirty clothing.

DELICATE: Wash clothing with the HAND WASH mark.

BLANKET: Wash strong for blankets or heavy clothing.

BABYCARE:  Wash gently and rinse thoroughly for baby clothing.

TUB CLEAN: Course for cleaning washing / spin drying tub. Select the washing time: 2 hrs, 6 hrs, 9 hrs.

*ECO: Water is saved by 1 time static rinse.

 WASH: Select WASH as necessary. Select the washing time: [ – ](= 0 min) , 1 min – 15 min.

RINSE: Select RINSE as necessary. Select the rinsing time: [ – ](= 0 min) , 1 time – 3 times.

SPIN: Select SPIN as necessary. Select the spinning time: [ – ](= 0 min) , 1 min – 9 min.

DRY: Course for reducing the time to dry. Spin-drying with high-speed takes air into the inner tub from the hole of top lid.
AIR DRY course reduce the time to dry in the shade greatly. Select the time: [ – ](= 0 min) , 30 min, 60 min, 90 min.

WATER LEVEL: Select the appropriate water level depending on course or kinds of clothing. (Select from 8 steps regulation).

Water inlet hose connecting port
For the prolonged use, the filter net is very easily blocked. Please clean it in the following way.

  1. urn off the faucet.
  2. Confirm if top cover is closed.
  3. . Dismantle water inlet hose.
  4. . Clean the filter net.

Lint filter box

  1. Detach lint filter box from washing tub.
  2. Clean lint filter box and the tub side.
  3. Attach lint filter box on washing tub to a down- -ward direction.

Washing / Spin Drying tub

  1. Each time after washing, please turn off the faucet and power. (If necessary, please dismantle water inlet hose.)
  2. Please wipe the water in the tub away after washing as soon as possible.
  3. Be sure to pull out the plug from the plug socket during maintenance.
  4. Hanging power cord and drain hose is desirable.
  5. Please open top cover for about 1 hour after wiping away the water and the persistent dirt in the tub cleanly with clean and soft cloth.
  6. Please do not use solvents such as alcohol, cleanser and so on, because they may cause damage to the surface of the tub.

Additional operating procedure

FRAGRANCE

  1. Press POWER ON/OFF key.
  2. Press COURSE key, and select the necessary course
  3. Press FRAGRANCE key, and the light turns on.
  4. Press START/ PAUSE key.

Things to know before washing 

Select the course depending on the type of clothing or degree of dirt on clothing.
After pressing START/PAUSE key once, you cannot change the course. When you want to change the course, turn off the power and select the desired course again.
Blinking display indicates the step in operation, lighting display indicates the course selected.
When motor get hot beyond a safe limit, it fail-safes on it and stops the operation. Do not use more than 3 continuous runs.

 

SHARP CORPORATION OSAKA, JAPAN