Yamaha SPS-3000 Speaker Stand Owner’s Manual


SPS-3000
Speaker Stand
Owner’s Manual

This product is a general household speaker stand developed for use with NS-3000.

♦ Specifications

Dimensions (W x H x D) 306 x 629 x 401 mm (12″ x 24-3/4″ x 15-3/4″)
(Not including the height of supplied spikes) Weight 15.3 kg (33.7 lbs.)
* The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest manual, access the Yamaha website then download the manual file.

CAUTION

  • The speaker stand should be set up or moved by two or more people. Otherwise, the speaker stand may fall or tip over, causing injuries.

NOTICE

  • First spread out blankets or soft cloths to prevent the floor from being scratched.

NOTE: This speaker stand is made with wooden parts. Screws may become loose due to expansion/ contraction of the wood caused by environmental changes or due to vibration during use. If that occurs, retighten the screws with a Phillips screwdriver.

Accessories

Before assembling the speaker stand, make sure that all accessories are included.

When setting up this speaker stand on a thick carpet. etc., installing the spikes can improve the sound quality and prevent wobbling. Refer to “Using the speaker stand with spikes (2)”.
NOTE
• Since pads are attached to the bottom of the speaker stand, it can be used without installing the spikes.

WARNING

  • To prevent accidental ingestion, keep spikes that arc not used out of the reach of children.

Using the speaker stand with spikes (2)

  1.  Spread out blankets or soft cloths on a level surface, and then lay the speaker stand on its side.
  2. Screw the spikes into the holes provided in the base.

CAUTION

  • Be careful since loosening the spikes too much may cause them to fall off.
  • Tilting the speaker stand to set it up requires two or more people so that it does not tip over.

NOTE

  •  Allowing the tips of the spikes to drag may scratch the floor. Be careful when installing the speaker or moving the speaker stand.
  • When the spikes are installed, be careful not to scratch the floor.
  • Due to the weight of the speaker stand and speaker, marks may be left on the floor or carpet.

Set up

Follow the procedure below to install speaker NS-3000 onto this speaker stand.
NOTE

  • This speaker stand can be used facing either forward or backward.
  • When installing the speaker. also, refer to its Owner’s Manual.

1.Place the speaker stand at the setup location.

CAUTION

  • Be sure to place this speaker stand on a level and stable floor surface. Otherwise, it may tip over, causing injuries.
  • Remove the speaker from the speaker stands before moving them. Two people should grin the column to move the speaker stand.

2.Place the speaker on the plate of the speaker stand.

CAUTION

  • When ben placing the speaker on Ibis speaker be sure not to pinch your fingers otherwise. injuries may result.

NOTE

  • Before performing operations. disconnect the speaker caNes lions the speakers
  • For details on the locations of the screen holes in the bottom of speaker NS•3000. refer to its Owner’s Manual

3.Align the screw holes in the bottom of the speaker with the holes in the plate and then insert the screws into the screw holes from the bottom of the plate and tighten them.

CAUTION

  • Be careful not to trip over the speaker cables. Otherwise, the speaker stand may tip over, causing injuries.
    NOTICE
  • Be sure to use the included screws to prevent the speaker from falling off.
  • While mounting the speaker onto the speaker stand, hold the speaker to prevent it from falling off.
  • Due to the material characteristics, the wood of the NS-3000 will shrink. In addition, the screws may become loose due to vibrations caused by music playback. If that occurs, retighten the screws.
  • When installing/removing the speaker, do not drag the speaker along the top of the speaker stand. Otherwise, the bottom of the speaker or top of the plate may be scratched or peeled off.
  • Do not overtighten the screws. Otherwise, the speaker stand or speaker may become damaged or deformed.

When using the speaker stand with spikes
After installing the 4 spikes. place the speaker stand at the setup location. If the speaker stand is wobbling. turn the spikes and adjust them so the speaker stand does not wobble.

CAUTION

• When adjusting the spikes while tilting the speaker stand, support the speaker stands and speaker by two or more people. Falling or toppling may result in injury or damage.

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE USE. BE SURE TO FOLLOW THESE INSTRUCTIONS.

The precautions listed below are to prevent the risk of harm to the user and others, as well as to prevent property damage. and to help the user use this unit properly and safely. Be sure to follow these instructions.
After reading this manual, be sure to keep it in a safe place where it can be referenced at any time.

  • Be sure to request inspections or repairs from the dealer where you purchased the unit or from qualified Yamaha service personnel.
  • Yamaha cannot be held responsible for injury to you or damage of the products caused by improper use or modifications to the
  • This product is for ordinary homes. Do not use for applications requiring high reliability. such as managing lives, health care or high-value assets.

WARNING

This content Indicates “risk of serious injury or death.”
If you notice any abnormality

  • If there is a crack or damage in the unit, immediately request an inspection or repair from the dealer where you purchased the unit or from qualified Yamaha service personnel. Continued use may cause the unit to fall or tip resulting in injuries or damage.

Installation

  • Assemble and install in the manner instructed in the manual. Falling or toppling may result in injury or
  • Confirm that the finished installation is safe and Also, carry out safety inspections periodically. Failure to observe this may cause devices to fall and result in injury.
  • Always fix the speaker cable to a wall or similar. If you catch your feet or hands on the cable, the speakers may fall or overturn, causing malfunctions or

Fire warning

  • Do not place any burning items or open flames near the unit, since they may cause a fire.

Handling

  • Keep small parts out of the reach of infants. Your children may accidentally swallow them.
  • Be careful not to drop or apply a strong impact to this unit. Failure to observe this may cause injuries or
  • Do not use for purposes other than speaker stand. Otherwise, damage or injuries may result.

CAUTION

This content indicates a “risk of injury.”

Installation

  • Do not place the unit in an unstable position where it might accidentally drop or fall over and cause injuries.
  • Do not install the unit in other ways than indicated. Failure to observe this may cause malfunctions or for the unit to fall and cause injury.
  • Avoid being near the unit during a disaster, such as an earthquake. Since the unit may turn over or fall and cause injury, quickly move away from the unit and go to a safe place.
  • When transporting or moving the unit always use two or more people. Attempting to lift the unit by yourself may damage your back, result in another injury, or cause damage to the unit itself.
  • Do not use other screws than the ones included in the accessories. Otherwise, damage or injuries may result.
  • Firmly tighten the screws. In addition, after a long period of use, check that no screws have become loose. Otherwise, the speaker may fall, causing injuries.
  • Before moving the speaker stand, remove the speaker. Otherwise, the speaker may fall, causing injuries.

Handling caution

  • Do not do the following:
  • Stand on or sit on the unit.
  • Place the unit in a stack.
  • Apply unreasonable force to the unit.
  • Hang on the unit.
  • Lean against the unit.

Failure to observe this may cause injuries or damage to the unit.

NOTICE

Indicates points that you must observe in order to prevent product deformation or damage to the unit and so on.

Installation

  • Do not use this unit in a location that is exposed to direct sunlight that becomes extremely hot, such as near a heater, or extremely cold, or that is subject to excessive dust or Failure to observe this may cause deformation or damage to the unit.
  • Do not install the unit in places where it may come into contact with corrosive gases or salt air or places that have excessive smoke or steam. Doing so may result in deformation or damage to the unit.

Do not disassemble

  • Do not modify this Failure to observe this may cause deformation.

Water warning

  • Do not use in humid or damp conditions, such as a bathroom or outside in the rain. Otherwise, damage or deformation may result.

Maintenance

  • If the temperature or humidity changes drastically, water droplets (condensation) may form on the unit If water droplets form, immediately wipe them off with a soft cloth. If water droplets are left on the unit, they may be absorbed into the wooden parts, causing deformation.
  • When cleaning the unit, use a dry. soft cloth. Using chemicals such as benzene or thinner, cleaning agents, or chemical scrubbing cloths can cause discoloration or

INFORMATION

About content in this manual

  • This manual is for the users of this unit.
  • This manual uses the following signal words for the important information:

WARNING

This content indicates a “risk of serious injury or death.”

CAUTION

This content indicates a “risk of injury.”

NOTICE
Indicates points that you must observe in order to prevent product deformation or damage to the unit and so on.
NOTE
Indicates notes on instructions, restrictions on functions, and additional information that may be helpful.

  • The illustrations in this manual are for instructional purposes

Yamaha Global Site https://www.yamaha.com
Yamaha Downloads https://download.yamaha.com
Manual Development Group © 2020 Yamaha Corporation
YAMAHA CORPORATION
10-1 Nakazawa-Cho, Naka-Ku, Hamamatsu, 430-8650 Japan