Honeywell CM4680 2D Imager Module User Guide

Honeywell CM4680 2D Imager Module User Guide

What is the CM4680 2D Imager Module

The CM4680 is an encased compact 2D imager module for fixed mount applications.

The CM4680 2D imager module includes the following features:

• USB interface (micro USB connector)
• Exit window
• Beeper
• Status indicator
• Mounting holes for multiple mounting positions
• Sealed enclosure

Required Accessories (not provided)

• Standard USB cable (USB-A to micro USB). Maximum recommended length is 3-5 meters.

Additional Documentation

The following document is available from your local Honeywell OEM representative:

• N4680/CF4680/CM4680 User Guide.

CM4680 2D Imager Module Views

Connecting to a Host

By default, the scanner is in USB serial interface.

1. Remove slider from module by pressing the ends and sliding it off.
   
2. Connect a standard USB cable (standard USB-A to micro USB) to the module.
   
3. Secure the cable to the module using the slider: Place the cable through the center of the slider. Press the ends of the slider and slide it back on to the module until tight
   
4. Connect the USB cable to the host.
5. Power-up the host.

The scanner powers up, emits a series of beeps from low to high, and lighting turns on.

Note: The host does not have to be powered down before plugging in the device. It can be hot plugged.

Configuration

You can configure your scanner two ways:

• Reading configuration bar codes
• Using the EZConfig Cloud for Scanning tool

Configuration Bar Codes

Scan configuration bar codes to set up your scanner. All available configuration bar codes are available in the N4680/ CF4680/CM4680 User Guide. Contact your local Honeywell OEM representative for more information.

EZConfig for Scanning Tool

Use the EZConfig for Scanning tool to configure your scanner Online:

1. Go to the Honeywell https://hsmftp.honeywell.com.
2. Register (if you haven’t already), then login.
3. Browse to Software > Barcode Scanners > Software > Tools and Utilities > EZConfig for Scanning > Current and download the tool.
4. Open EZConfig to configure your scanner.

Basic Setup

Here are some basic menu bar codes that may be useful for testing. For more setup options see the N4680/CF4680/CM4680 User Guide (available from your local Honeywell OEM represen- tative).

Note: The * symbol indicates the default value.

Interface

For USB serial interface, you must install the USB driver before
connecting your scanner. You can find the most current USB
driver at hsmftp.honeywell.com.

• USB Serial Interface *
  
• USB PC Keyboard
  

Keyboard Country Layout

the default keyboard is United States.

• United States
  
• French
  
• German
  
• Italian
  

Beeper Volume

• Low
  
  
• Medium
  
• High
  
• Off
  

Presentation Mode

The scanner LEDs remain dim and aimer off until a movement is detected, then the aimer turns on and LEDs light up to read the bar code.

There are 2 types: Presentation Mode or Presentation Mode— Extended Reading Range.

Presentation Mode: Optimized scan speed, limited reading range.

• Presentation Mode
  
  

Presentation Mode—Extended Reading Range: Optimized reading range, low scan speed.

Mobile Phone Read Mode

When this mode is selected, your scan engine is optimized to read barcodes from mobile phones or other LED displays.
Streaming Presentation – Mobile Phone

Streaming Presentation

The scanner LEDs are on all the time (continuous) and the aimer is off until a movement is detected, then the aimer turns on to read the bar code.

There are 2 types: Normal or Enhanced.

Streaming Presentation—Normal: Fast scan speed, limited reading range.

Streaming Presentation—Enhanced: Fastest possible scan speed, slightly less reading range than Normal Streaming Pre- sentation mode.

Reset Factory Defaults

The following bar code resets factory defaults.

Mechanical Dimensions

Units are in millimeters. Tolerances: ±0.5 mm.

Mounting Holes

Use M3 screws with a maximum depth of 5.8 mm/0.23 in. Max torque 4.5kgf.cm/3.9 lbf.in and pull out resistance 736N.

Units are in millimeters. Tolerances ±0.5 mm.

Recommendations

• Do not add an exit window over the existing exit window.
• For best beeper performance, do not fully cover the beeper opening.
• Be sure the cable is fitted tightly in the connector using the cable slider. The cable over mold should not be more than 23 mm/0.90 in.

Technical Specifications

Reading Distances

• Measured from the front center of the housing
• 25°C, 200 lux for typical, 0 lux for guaranteed
• Photographic barcodes
• Serial Trigger mode

Typical

Guaranteed

Customer Support and Technical Assistance

For customer support, contact your local Honeywell Sales Representative or fill out the support form at sps.honeywell.com/us/en/contact-us.

Limited Warranty

For warranty information, go to sps.honeywell.com/us/en/support/ productivity/warranties.

Patents

For patent information, see sps.honeywell.com/us/en/support/patents.

Disclaimer

Honeywell International Inc. and its affiliates, subsidiaries, and other entities forming part of Honeywell group (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of HII.

Honeywell warrants goods of its manufacture as being free of defective materials and faulty workmanship during the applicable warranty period. Honeywell’s standard product warranty applies unless agreed to otherwise by Honeywell in writing; please refer to your order acknowledgment or consult your local sales office for specific warranty details. If warranted goods are returned to Honeywell during the period of coverage, Honeywell will repair or replace, at its option, without charge those items that Honeywell, in its sole discretion, finds defective. The foregoing is buyer’s sole remedy and is in lieu of all other warranties, expressed or implied, including those of merchantability and fitness for a particular purpose. In no event shall Honeywell be liable for consequential, special, or indirect damages. While Honeywell may provide application assistance personally, through our literature and the Honeywell web site, it is buyer’s sole responsibility to determine the suitability of the product in the application. Specifications may change without notice. The information we supply is believed to be accurate and reliable as of this writing. However, Honeywell assumes no responsibility for its use.

This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated into another language without the prior written consent of HII.

Copyright  2021 Honeywell International Inc. All rights reserved.

Web Address: sps.honeywell.com/us/en/products/sensing-and-iot

Other product names or marks mentioned in this document may be trademarks or registered trademarks of other companies and are the property of their respective owners.