Whirlpool W11366704A Side by Side Refrigerator Owner’s Manual

INSTALLATION INSTRUCTIONS
AND OWNER’S MANUAL
Side by Side Refrigerator
Do Not Throw Away – Additional important safety information is included.
Para las instrucciones en español, visite nuestro sitio de internet.

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These words mean:

DANGER: You can be killed or seriously injured if you don’t immediately follow instructions.

WARNING: You can be killed or seriously injured if you don’t follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock or injury to persons when using the refrigerator, follow basic precautions, including the following:

•  Plug into a grounded 3-prong outlet.
• Do not remove the ground prong.
• Do not use an adapter.
•  Do not use an extension cord.
• Disconnect power before servicing.
•  Replace all parts and panels before operating.
•  Remove doors from your old refrigerator.
•  Connect only to the potable water supply.
•  Use non-flammable cleaner.
• Keep flammable materials and vapors, such as gasoline, well away from the refrigerator.
• Use two or more people to move and install the refrigerator.
• Disconnect the power before installing the ice maker (on ice maker kit ready models only).
• Use a sturdy glass when dispensing ice (on some models).
•  Do not hit the refrigerator glass doors (on some models).
•  This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities,  or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or a similarly qualified person in  order to avoid a hazard.
• Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.
• This appliance is intended to be used in household and similar applications such as:
  • Staff kitchen areas in shops, offices, and another working environment;
  • Farmhouses and by clients in hotels, motels, and other residential type environments;
  • Bed and breakfast type environments;
  • Catering and similar non-retail applications.

Proper Disposal of Your Old Refrigerator

WARNING: Suffocation Hazard Remove doors from your old refrigerator. Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous, even if they will  sit for “just a few days.” If you are getting rid of your old refrigerator, please follow these instructions to help prevent accidents.
Before You Throw Away Your Old Refrigerator or Freezer:

• Take off the doors.
• Leave the shelves in place so that children may not easily climb inside.

Important information to know about the disposal of refrigerants:
Dispose of the refrigerator in accordance with Federal and Local regulations. Refrigerants must be evacuated by a licensed, EPA-certified refrigerant technician in accordance with established procedures.

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator
WARNING: Excessive Weight Hazard Use two or more people to move and install the refrigerator.
Failure to do so can result in back or another injury.

Remove packing materials. Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator. For more information, see “Refrigerator Safety.”

When Moving Your Refrigerator: Your refrigerator is heavy. When moving the refrigerator for cleaning or service, be sure to cover the floor with cardboard or hardboard to avoid floor damage. Always pull the refrigerator straight out when moving it. Do not wiggle or “walk” the refrigerator when trying to move it, as floor damage could occur.

Important information to know about glass shelves and covers: Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. Tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping.

Door Removal, Leveling, and Alignment

Gather the required tools and parts and read all instructions before starting installation. Save these instructions for future reference.
NOTE: Before moving your product into your home, measure the doorway of your home to see whether you need to remove the refrigerator and freezer doors. If door removal is necessary, see the instructions below.
IMPORTANT: Before you begin, unplug the refrigerator or disconnect power. Remove food, the ice storage bin (on some models), and any adjustable door or utility bins from doors.
TOOLS NEEDED: Bubble level; flat-blade screwdriver; 5/16″ and 11/16″ wrench; 1/4″, 3/8″, and 5/16″ hex-head socket wrenches, Phillips screwdriver tip #2 with 4″ long as a minimum, TORX T30 † screwdriver.

Remove the Doors

If your refrigerator does not fit through the doorway or you are getting rid of your old refrigerator, follow the steps below for door removal.

1.  Unplug the refrigerator or disconnect power.
2. Fully open both doors. See graphic 1.
3. If your model has water dispensing, please open the water filter door by pulling it toward you. See graphic 2. It is not necessary to remove the water filter itself.
4. Pull the base grille toward you from the sides and then from the center until it dislodges. See graphic 2.
5. To remove the base grille, twist and pull the right side until this side passes underneath the refrigerator door. See graphic 3.  Then pull the left side of the base grille for complete removal.
6. If your model has water dispensing in the door, disconnect the water dispenser tubing located below the freezer door.
   ■ Press the blue outer ring against the face of fitting and pull the dispenser tubing free. See graphic 4.
   NOTE: Keep the water tubing connector attached to the tube that runs underneath the freezer. The door cannot be removed if the connector is still attached to the tube that runs through the door hinge.
7.  If your model has water dispensing in the door, disconnect the wiring located below the freezer door. See graphic 5.
   ■ Remove the wiring clip and the bracket wire using a 1/4″ hexagonal head socket wrench.
   ■ Disconnect the wiring plugs from the bracket wire.
8. Close the freezer door and use a TORX T30 screwdriver to remove the top hinge completely. See graphic 6.
   IMPORTANT: Do not remove either screw A. Hold the door while the hinge is being removed.
9.  Lift the freezer door straight up off from the bottom hinge. See graphic 7. The water dispenser tubing and wiring will remain attached to the freezer door.
   NOTE: This may require two people, one to lift the door and another to feed the water tubing and wiring into the bottom hinge pin.
   IMPORTANT: Rest the door on its side on a soft, clean surface, such as a towel, blanket, or piece of cardboard. This will help to avoid scratching or damaging the door, water tubing, and wiring.
10. Close the refrigerator door and use a TORX T30 screwdriver to remove the completely top hinge. See graphic 8.
    IMPORTANT: Do not remove either screw A. Hold the door while the hinge is being removed.
11. Lift the refrigerator door straight up off from the bottom hinge. See graphic 7.
    IMPORTANT: Rest the door on its side on a soft, clean surface, such as a towel, blanket, or piece of cardboard. This will help to avoid  scratching or damaging the door
12. If your refrigerator without doors does not pass through the doorway, you may remove both bottom hinges. Use a 5/16″ nut driver to remove these. See graphic 9.

Replacing or Reinstalling Door and Hinges

If your doors and bottom hinges have been removed, please follow the next instructions for re-installation:

1.  Reinstall both bottom hinges using a 5/16″ nut driver to tighten screws. See graphic 9.
2.  If your model has water dispensing in the door:
   ■ Lift the freezer door enough to feed the water dispenser tubing and wiring through the bottom hinge pin.
   NOTE: This may require two people, one to lift the door and the other to feed the water tubing and wiring into the bottom hinge pin. See graphic 7.
   ■ Insert the freezer door into the bottom hinge pin.
   IMPORTANT: Hold the door while the hinge is being installed
3. Close the freezer door to align and reinstall the top hinge. Use a TORX T30 screwdriver to tighten the screws. See graphic 8.
   IMPORTANT: Provide additional support for the door while the top hinge is being reinstalled. Do not depend on the door magnets to assure the door to the cabinet.
4. If your model has water dispensing in the door, connect the water dispenser tubing. For the connection, push the tubing into the dispenser tubing until a black mark touches the face of fitting. See graphic 4.
5. Connect the wiring. See graphic 5.
6.  Reinstall the wiring clip & the bracket wire using a 1/4″ hexagonal head socket wrench.
7.  Connect the wiring plugs from the bracket wire.
8.  Lift the refrigerator door enough to insert the door into the bottom hinge pin. See graphic 7.
   IMPORTANT: Hold the door while the hinge is being installed.
9. Close the refrigerator door to align and reinstall the top hinge. Use a TORX T30 screwdriver to tighten the screws. See graphic 6.
   IMPORTANT: Provide additional support for the door while the top hinge is being reinstalled. Do not depend on the door magnets to assure the door to the cabinet.

Leveling and Door Closing

Your refrigerator has two front adjustable wheels. See graphic 1. These are used to level the refrigerator under uneven floor conditions or want the doors to close more easily. Please follow the instructions below:

1. Use a Bubble level to check the levelness of the floor where the rear side of the refrigerator will rest. If the refrigerator is not leveled, adjust or add the shim on flooring to create a leveled floor for the rear side wheels. A leveled rear side prevents the refrigerator cabinet from forming a twist.
2. Place the refrigerator into its final location in the kitchen and open both doors.
3. Fully open both doors. See graphic 1.
4.  If your model has water dispensing in the door, please open the water filter door by pulling it toward you. See graphic 2. It is not necessary to remove the water filter itself.
5. Pull the base grille toward you from the sides and then from the center until it dislodges. See graphic 2.
6. To remove the base grille, twist and pull the right side until this side passes underneath the refrigerator door. See graphic 3. Then pull the left side of the base grille for complete removal.
7. Raise the wheels while one person pushes on the refrigerator to lift from the front side. Use the bubble level on top of the refrigerator or on its side to level the refrigerator. Check bubble level and at the same time observe the gaps and squareness to the adjacent cabinets, furniture or trim. If adjacent furnishings are not level, it may not be possible to achieve even gaps when the product is level. Continue adjusting until all four corners are steady without rock.
8. Use a 3/8″ nut driver to turn the leveling screws located on both sides of the refrigerator. See graphic 10. Depending on uneven floor conditions,  you must turn one or both screws to the right or left several times to raise or lower the refrigerator.
9. Close both doors and check that they close as easily as you like. If not, turn both screws to the right to raise the refrigerator by tiling it more to the back until the doors close as easily as you like.
10. Check and make sure the technician sheet is placed in the base grille cavity before assembling this into the cabinet.
11. Reinstall the base grille into the cabinet, introducing the left side first and then the right side of the base grille. See graphic 3. You may accommodate the water dispenser tubing and wiring into the base grille cavity below the left bottom hinge.
12. Attach the base grille pushing into the cabinet clips. See graphic 2.

Door Alignment
The refrigerator doors are designed to be slightly misaligned vertically when the refrigerator is empty. Please follow the next steps to align the refrigerator doors.

1. Use an 11/16″ open-ended wrench tool to loosen the locking nut located below the refrigerator door. See graphic 11. Accommodate the wrench tool so that it fits in the space.
2. Use a 5/16″ open-ended wrench tool to turn the alignment screw. See picture 12. Depending on how the refrigerator door is misaligned in relation to the freezer door, you must turn the screw to the right to raise or to the left to lower the refrigerator door until both doors have been aligned vertically.
3.  Tighten the 11/16″ locking nut with the wrench tool.
4. Attach the base grille if it was dislodged.

Handle Installation and Removal

PARTS INCLUDED: Door handles (2), 1/8″ hex key, spare setscrew(s)
To Install the Handles:
NOTE: The handle mounting setscrews are preinstalled in the handle.

1. Remove the handles, which are packed inside the refrigerator.
   NOTE: To avoid scratching the finish, place the handles on a towel or other soft surface.
2. Open the freezer door. On the refrigerator door, place the handle on the shoulder screws with the setscrews facing the freezer.
   
3. Firmly push the handle toward the door until the handle base is flush against the door.
4. While holding the handle, insert the short end of the hex key into the upper hole and slightly rotate the hex key until it is engaged in the setscrew.
   
5. Using a clockwise motion, tighten the setscrew until it begins to contact the shoulder screw.
6.  Repeat steps 4 and 5 to begin fastening the lower set screw.
7. Once both setscrews have been partially tightened as outlined in the previous steps, fully tighten both the upper and lower setscrews.
   IMPORTANT: When the screws feel tight, tighten them an additional quarter-turn. The handle is not properly installed without this extra tightening.
8. Open the refrigerator door and close the freezer door. Repeat steps 2 through 7 to install the other handle onto the freezer door with the setscrews facing the refrigerator.
9. Save the hex key and all instructions.

To Remove the Handles:

1. While holding the handle, insert the short end of the hex key into the lower setscrew hole and slightly rotate the hex key until it is engaged in the setscrew.
2. Using a counterclockwise motion, loosen the setscrew a quarter-turn at a time.
3. Repeat steps 1 and 2 for the upper setscrew. Gently pull the handle away from the door.
4. If necessary, use a Phillips screwdriver to remove the shoulder screws from the door.

Location Requirements

IMPORTANT: This refrigerator is designed for indoor household use only.

To ensure proper ventilation for your refrigerator, allow for 1/2″ (1.27 cm) of space on each side and at the top. Allow for 2″ (5.08 cm) of space behind the refrigerator. If your refrigerator has an ice maker, allow extra space at the back for the water line connections. When installing your refrigerator next to a fixed wall, leave a 2″ (5.08 cm) minimum space on each side (depending on your model) to allow the doors to swing open.
NOTES:

• This refrigerator is intended for use in a location where the temperature ranges from a minimum of 55°F (13°C) to a maximum of 110°F (43°C).  The preferred room temperature range for optimum performance, which reduces electricity usage and provides superior cooling, is between 60°F  (15°C) and 90°F (32°C). It is recommended that you do not install the refrigerator near a heat source, such as an oven or radiator.
• The normal minimum cabinet cut-out width required for product installation is 36″ (91.44 cm). However, if the product is placed against an extended wall and the ability to remove the crisper pans is desired, an additional 18″ (45.72 cm) of cabinet width is required, so a total cabinet opening width of 54″ (137.16 cm) is recommended.

Electrical Requirements

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection.
Recommended Grounding Method
A 115 V, 60 Hz, AC only, 15 or 20 A fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord.
NOTE: Before performing any type of installation or cleaning, or removing a light bulb, disconnect the refrigerator from the electrical source. When you are finished, reconnect the refrigerator to the electrical source and reset the control (Thermostat, Refrigerator, or Freezer Control depending on the model) to the desired setting. See the “Using the Controls” section in the User Instructions, User Guide, or Use and Care Guide.

Water Supply Requirements
Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

TOOLS NEEDED:

• Flat-blade screwdriver
• 7/16″ and 1/2″ open-end or two adjustable wrenches
• 1/4″ nut driver
• 1/4″ drill bit
• Cordless drill

NOTE: Your refrigerator dealer has a kit available with a 1/4″ (6.35 mm) saddle-type shutoff valve, a union, and copper tubing. Before purchasing,  make sure a saddle-type valve complies with your local plumbing codes. Do not use a piercing-type or 3/16″ (4.76 mm) saddle valve which reduces water flow and clogs more easily.

IMPORTANT:

• All installations must meet local plumbing code requirements.
• Use copper tubing and check for leaks. Install copper tubing only in areas where the household temperatures will remain above freezing.

Water Pressure

A cold water supply with water pressure of between 30 and 120 psi (207 and 827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

• If your refrigerator has a water dispenser: After installation is complete, use the water dispenser to check the water pressure.
• With the water filter removed, dispense 1 cup (237 mL) of water. If 1 cup of water is dispensed in 8 seconds or less, the water pressure to the refrigerator meets the minimum requirement.
• If it takes longer than 8 seconds to dispense 1 cup of water, the water pressure to the refrigerator is lower than recommended. See “Problem  Solver” for suggestions.

Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of a reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 30 and 120 psi (207 and 827 kPa).
If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a  minimum of 40 to 60 psi (276 to 414 kPa).
If the water pressure to the reverse osmosis system is less than 40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.
• Allow the storage tank on the reverse osmosis system to refill after heavy usage.
• If your refrigerator has a water filter, it may further reduce the water pressure when used in conjunction with a reverse osmosis system. Remove the water filter. See “Water Filtration System” in the User Instructions, User Guide, or Use & Care Guide. If you have questions about your water pressure, call a licensed, qualified plumber.

If you have questions about your water pressure, call a licensed, qualified plumber.

Connect Water Supply
Read all directions before you begin. IMPORTANT:

• Connect to potable water supply only.
  Do not use water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.
• Plumbing shall be installed in accordance with the International Plumbing Code and any local codes and ordinances.
• The gray water tubing on the back of the refrigerator (which is used to connect to the household water line) is a plastic tube. Copper and plastic tubing connections from the household water line to the refrigerator are acceptable and will help avoid off-taste or odor in your ice or water.  Check for leaks.
  If plastic tubing is used instead of copper, we recommend the following Whirlpool Part Numbers: W10505928RP (7 ft [2.14 m] jacketed plastic), 8212547RP (5 ft [1.52 m] plastic), or W10267701RP (25 ft [7.62 m] plastic).
• Install tubing only in areas where temperatures will remain above freezing.

TOOLS NEEDED:
Gather the required tools and parts before starting installation.

• Flat-blade screwdriver
• 7⁄16″ and 1/2″ open-end wrenches or two adjustable  wrenches
• 1/4″ nut driver

Connect to Water Line

IMPORTANT: If you turn the refrigerator on before the water line is connected, turn the ice maker OFF.
Style 1 (Recommended)

1.  Unplug the refrigerator or disconnect power.
2. Turn OFF the main water supply. Turn ON the nearest faucet long enough to clear the line of water.
3.  Use a quarter-turn shutoff valve or the equivalent, served by a 1/2″ copper household supply line.
   NOTE: To allow sufficient water flow to the refrigerator, a minimum 1/2″ size copper household supply line is recommended.
   A. Bulb
   B. Nut
   C. Copper tubing (to the refrigerator)
   D. Household supply line (½” minimum)
4. Now you are ready to connect the copper tubing to the shutoff valve. Use 1⁄4″ (6.35 mm) OD soft copper tubing to connect the shutoff valve and the refrigerator.
   •  Ensure that you have the proper length needed for the job. Be sure both ends of the copper tubing are cut square.
   •  Slip compression sleeve and compression nut onto copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go.  Screw compression nut onto outlet end with an adjustable wrench. Do not overtighten.
   
5. Place the free end of the tubing into a container or sink, and turn on the main water supply to flush out tubing until water is clear. Turn off the shutoff valve on the water pipe.
   NOTE: Always drain the water line before making the final connection to the inlet of the water valve to avoid possible water valve malfunction.
6. Bend the copper tubing to meet the water line inlet, which is located on the back of the refrigerator cabinet as shown. Leave a coil of copper tubing to allow the refrigerator to be pulled out of the cabinet or away from the wall for service.

Style 2

1.  Unplug the refrigerator or disconnect power.
2. Turn OFF the main water supply. Turn ON the nearest faucet long enough to clear the line of water.
3. Locate a 1/2″ (1.27 cm) to 1¼” (3.18 cm) vertical cold water pipe near the refrigerator.
   IMPORTANT:
   • Make sure it is a cold water pipe.
   • Horizontal pipe will work but drill on the top side of the pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.
4. Determine the length of copper tubing you need. Measure from the connection on the lower rear corner of the refrigerator to the water pipe. Add 7 ft  (2.1 m) to allow for cleaning. Use 1/4″ (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square
5. Using a cordless drill, drill a 1⁄4″ (6.35 mm) hole in the cold water pipe you have selected.
   

   A. Cold water pipe	E. Compression sleeve
   B. Pipe clamp	F. Shut-off valve
   C. Copper tubing	G. Packing nut
   D. Compression nut

6. Fasten the shutoff valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the ¹⁄4″ (6.35 mm) drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws slowly and evenly so the washer makes a  watertight seal. Do not overtighten, or you may crush the copper tubing.
7. Slip the compression sleeve and compression nut on the copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw the compression nut onto the outlet end with an adjustable wrench. Do not overtighten.
8. Place the free end of the tubing in a container or sink, and turn ON the main water supply. Flush the tubing until water is clear. Turn OFF the shutoff valve on the water pipe. Coil the copper tubing.

Connect to Refrigerator

Style 1

1. Unplug the refrigerator or disconnect power.
2.  Remove and discard the short, black plastic part from the end of the water line inlet.
3. Thread the nut onto the end of the tubing. Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten.
   NOTE: To avoid rattling, be sure the copper tubing does not touch the cabinet’s sidewall or other parts inside the cabinet.
   

   A. Household water line	C. Ferrule (purchased)
   B. Nut (purchased)	D. Refrigerator water tubing

4. Install the water supply tube clamp around the water supply line to reduce strain on the coupling.
5. Turn shutoff valve ON.
6. Check for leaks. Tighten any connections (including connections at the valve) or nuts that leak.

Style 2

1. Unplug the refrigerator or disconnect power.
2. Remove and discard the plastic part that is attached to the inlet of the water valve.
3. Attach the copper tube to the valve inlet using a compression nut and sleeve as shown. Tighten the compression nut. Do not overtighten.
4. Use the tube clamp on the back of the refrigerator to secure the tubing to the refrigerator as shown. This will help avoid damage to the tubing when the refrigerator is pushed back against the wall.
5. Turn shutoff valve ON.
6. Check for leaks. Tighten any connections (including connections at the valve) or nuts that leak.
   

   A. Tube clamp	D. Compression nut
   B. Tube clamp screw	E. Valve inlet
   C. Copper tubing

7. On some models, the ice maker is equipped with a built-in water strainer. If your water conditions require a second water strainer, install it in the  1/4″ (6.35 mm) water line at either tube connection. Obtain a water strainer from your nearest appliance dealer.

Style 3

1.  Unplug the refrigerator or disconnect power.
2. Remove and discard the black nylon plug from the gray water tube on the rear of the refrigerator.
3.  If the gray water tube supplied with the refrigerator is not long enough, a 1/4″ x 1/4″ (6.35 mm x 6.35 mm) coupling is needed in order to connect the water tubing to an existing household water line. Thread the provided nut onto the coupling on the end of the copper tubing.
   NOTE: Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten.
   

   A. Refrigerator water tubing	E. Ferrule (purchased)
   B. Nut (provided)	F. Nut (purchased)
   C. Bulb	G. Household water line
   D. Coupling (purchased)

4. Turn shutoff valve ON.
5.  Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.

Complete the Installation

WARNING

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove the ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock.

1.  Plug into a grounded 3 prong outlet.
2. Flush the water system. See “Water and Ice Dispensers” in the User Instructions or User Guide.
   NOTE: Allow 24 hours to produce the first batch of ice. Allow 72 hours to completely fill ice container.

REFRIGERATOR CARE

Cleaning


WARNING

Explosion Hazard Use non-flammable cleaner. Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically. However, clean both sections about once a month to avoid the buildup of odors. Wipe up spills immediately.

IMPORTANT: Because air circulates between both sections, any odors formed in one section will transfer to the other. You must thoroughly clean both sections to eliminate odors. To avoid odor transfer and drying out of food, wrap or cover foods tightly.
To Clean Your Refrigerator:
NOTE: Do not use abrasive or harsh cleaners such as window sprays, scouring cleansers, flammable fluids, cleaning waxes, concentrated detergents,  bleaches, or cleansers containing petroleum products on plastic parts, interior, and door liners or gaskets. Do not use paper towels, scouring pads, or other harsh cleaning tools.

1. Unplug the refrigerator or disconnect power.
2. Hand wash, rinse, and dry removable parts and interior surfaces thoroughly. Use a clean sponge or soft cloth and a mild detergent in warm water.
3. Wash stainless steel and painted metal exteriors with a clean sponge or soft cloth and a mild detergent in warm water.
4. There is no need for routine condenser cleaning in normal home operating environments. If the environment is particularly greasy or dusty, or there is significant pet traffic in the home, the condenser should be cleaned every 2 to 3 months to ensure maximum efficiency.
   If you need to clean the condenser:
   • Remove the base grille. See the “Door Removal” instructions, either in the User Instructions or the Installation Instructions and Owner’s  Manual or in the separate instruction sheet provided with your refrigerator.
   • Use a vacuum cleaner with a soft brush to clean the grille, the open areas behind the grille, and the front surface area of the condenser.
   •  Replace the base grille when finished.
5. Plug in the refrigerator or reconnect power.

IMPORTANT: The lighting system in this appliance may consist of:

• Sealed LED modules
• LED Bulbs
• Incandescent Bulbs
• Or a combination of the above.

If a Sealed LED Module(s) do not illuminate when the refrigerator and/or freezer door is opened, call whirlpool service for technical support. (See  User Guide). See “Warranty” for contact information. IF a LED Bulb or the incandescent bulb does not turn ON when the refrigerator and/or freezer  door is opened, replace with a bulb recommended by Whirlpool and following the next procedure:

1. Unplug the refrigerator or disconnect power.
2. Remove light cover (in some models).
   NOTE: To clean the light cover, follow the instructions in
   REFRIGERATOR CARE section.
3. Remove the light bulb and replace it with one of the same sizes, shape, and wattage, recommended by Whirlpool.
4. Reinstall light cover (in some models).
5. Plugin the refrigerator or reconnect power.

NOTE: Not all appliance bulbs will fit your refrigerator. Be sure to replace the bulb with one of the same si ze and shape. On some models, the interior lights require a 40 W bulb max.

Vacation and Moving Care

Vacations
If You Choose to Leave Refrigerator On While You Are Away:

1. Use up any perishables and freeze other items.
2. If your refrigerator has an automatic ice maker and is connected to the household water supply, turn off the water supply to the refrigerator.  Property damage can occur if the water supply is not turned off.
3. If you have an automatic icemaker, turn off the ice maker.
   NOTE: Depending on your model, raise the wire shutoff arm to OFF (up) position or press the switch to OFF (right).
4. Empty the ice bin.

If You Choose to Turn Refrigerator Off Before You Leave:

1. Remove all food from the refrigerator.
2. If your refrigerator has an automatic ice maker:
   • Turn off the water supply to the ice maker at least one day ahead of time.
   • When the last load of ice drops, raise the wire shutoff arm to the OFF (up) position or move the switch to the OFF (right) setting.
3. Unplug refrigerator.
4. Clean, wipe and dry thoroughly.
5. Tape rubber or wood blocks to the tops of both doors to prop them open far enough for air to get in. This stops odor and mold from building up.

Moving
When you are moving your refrigerator to a new home, follow these steps to prepare it for the move.

1. If your refrigerator has an automatic ice maker:
   • Turn off the water supply to the ice maker at least one day ahead of time.
   • Disconnect the water line from the back of the refrigerator.
   • When the last load of ice drops, raise the wire shutoff arm to the OFF (up) position or move the switch to the OFF (right) setting.
2. Remove all food from the refrigerator and pack all frozen food in dry ice.
3. Empty the ice bin.
4. Unplug refrigerator.
5. Clean, wipe and dry thoroughly.
6. Take out all removable parts, wrap them well, and tape them together so they don’t shift and rattle during the move.
7. Depending on the model, raise the front of the refrigerator so it rolls more easily OR screws in the leveling legs so they don’t scrape the floor. See  “Adjust the Doors” or “Door Removal, Leveling and Alignment.”
8. Tape the doors closed and tape the power cord to the back of the refrigerator.
   When you get to your new home, put everything back and refer to the Installation Instructions for preparation instructions. Also, if your refrigerator has an automatic icemaker, remember to reconnect the water supply to the refrigerator.
   

Vacation and Moving Care

Vacations
If You Choose to Leave Refrigerator On While You Are Away:

1. Use up any perishables and freeze other items.
2. If your refrigerator has an automatic ice maker and is connected to the household water supply, turn off the water supply to the refrigerator.  Property damage can occur if the water supply is not turned off.
3. If you have an automatic icemaker, turn off the ice maker. NOTE: Depending on your model, raise the wire shutoff arm to OFF (up) position or press the switch to OFF (right).
4. Empty the ice bin.

If You Choose to Turn Refrigerator Off Before You Leave:

1. Remove all food from the refrigerator.
2. If your refrigerator has an automatic ice maker:
   • Turn off the water supply to the ice maker at least one day ahead of time.
   • When the last load of ice drops, raise the wire shutoff arm to the OFF (up) position or move the switch to the OFF (right) setting.
   3. Unplug the refrigerator.
   4. Clean, wipe and dry thoroughly.
   5. Tape rubber or wood blocks to the tops of both doors to prop them open far enough for air to get in. This stops odor and mold from building up.

FREEZER SHELF

(number of shelves varies by model)
To Remove and Replace the Bottom Shelf:

1. Lift up the front and back of the shelf, and remove from the
   cabinet. Be sure not to remove the retaining rods.
2. Replace the shelf aligning the rods with the cabinet ribs.
   Apply a little pressure on the shelf to attach the rods to the
   ribs of the cabinet.

To Remove and Replace the Mid and Top Shelf:

1.  With your hand, push the shelf from bottom to top until it is released from the holding rod. Pull the shelf until it is released from the rear rod.  Remove from the cabinet.
2. To replace the shelf:
   • Replace rods into the support holes. Push the rods down so it clicks into the hole.
   • Identify the front and rear trim of the shelf.
   • Place the rear trim on the rear rod and push the shelf so it clicks the rod into the trim rear. (Keep the front raised while pushing).
   •  Lower the front of the shelf until the front trim is on the rod and push the shelf down so it clicks the rod into the trim rear.

NOTE: Be sure that both sides of the shelf are positioned evenly in the shelf support holes and the shelf is secure.

TROUBLESHOOTING

First, try the solutions suggested here or visit our website to possibly avoid the cost of a service call.

 

 

 

 

PERFORMANCE DATA SHEET

Water Filtration System
Model P5WB2L/P4RFWB Capacity 200 Gallons (757 Liters)

This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the
the permissible limit for water leaving the system, as specified in NSF/ANSI Standards 42 and 53.