Motorola PMLN5729 IMPRES Ear Microphone System User Guide

IMPRES
EAR MICROPHONE
SYSTEM
PMLN5729
USER GUIDE

FOREWORD
Product Safety and RF Exposure
Compliance

Before using this product, read the operating instructions for safety usage contained in the Product Safety and RF Exposure booklet enclosed with your radio.

ATTENTION!
This ear microphone, when attached to the radio, is restricted to occupational use only to satisfy FCC/ICNIRP RF energy exposure requirements.
ACOUSTIC SAFETY
Exposure to loud noises from any source for extended periods of time may temporarily or permanently affect your hearing. The louder the radio’s volume, the less time is required before your hearing could be affected.
Hearing damage from loud noise is sometimes undetectable at first and can have a cumulative effect.
To protect your hearing :

  • Use the lowest volume necessary to do your job.
  • Turn up the volume only if you are in noisy surroundings.
  • Turn down the volume before connecting the headset or earpiece.
  • Limit the amount of time you use headsets or earpieces at high volume.
  •  When using the radio without a headset or earpiece, do not place the radio’s speaker directly against your ear.

DESCRIPTION
The Bone Conduction Ear Microphone PMLN5729 is equipped with a high-performance bone conduction microphone and receiver built into the earpiece. Unlike the conventional boom microphone, the bone conduction microphone picks up your voice directly from the ear canal, so ambient noise is minimized to its lowest level.

Figure 1: Ear Microphone Overview

PERFORMANCE
To minimize interference and optimize the Bone Conduction Ear Microphone performance, make sure the accessory cable does not coil around the radio antenna during use. The PTT has a rotating clip to secure it to clothing at the preferred position.
OPERATION

  1. Always turn the radio OFF before connecting the Bone Conduction Ear Microphone.
  2. Attach the accessory connector to the mating radio side connector.
    Figure 2: Secure the accessory connector
  3.  Ear mic fitting guide.
    Figure 3: Place earpiece in-ear. Figure 4: Push earpiece fully into the ear canal. Make sure the earpiece sits comfortable and snug inside your ear.
    Figure 5: Route the cable behind the ear. This step helps to hold the earpiece in place. Figure 6: Test earpiece on radio. Audio clarity may differ for different users depending on the earpiece fitting.
  4. Turn the radio ON.
    Do not set the volume level
    too loud.

    Note: Once the kit has been installed, the radio microphone and the radio speaker will be disabled. The user must use the Bone Conduction Ear Microphone to transmit and receive calls.

  5.  Press accessory PTT button to transmit (the radio-in-transmission light (LED) will be illuminated) and release the button to receive.
  6. Always turn the radio OFF before disconnecting the kit.

    7. ADDITIONAL FEATURES
    This Bone Conduction Ear Microphone has a programmable button.
    Using the Programmable Button
    The Accessory No Dot button is programmable through the radio’s CustomerProgramming Software (CPS). Your radio user guide contains full description of the programmable functions that are available through this button. Check with your local dealer for more information supporting the programmable button.
    SERVICE
    The replacement and alternative parts shown in Table 1 are available for the Bone Conduction Ear Microphone kit. Please contact your local Motorola Solutions Representative or Dealer for details.

    Part Description Part Number
    Eartip size M PMLN5510
    Eartip size S PMLN5511
    Isolator PMLN5512

    Table 1. Replacement Parts

    EARTIP REPLACEMENT
    There are two sizes of eartip available. The Bone Conduction Ear Microphone is shipped with a size M ear tip, while a size S ear tip is included separately in the package.
    Detach
    Position the earpiece so that it points up. Remove the ear tip in a turning motion and pull.

    Attach
    Insert the ear tip into the earpiece.

    Note: Ensure that the ear tip is properly attached to the earpiece. Even a slight gap diminishes performance quality.

    Note: Take extra caution not to lose the sound tube attached to the earpiece when removing the ear tip. Without it, the microphone may not function properly.

    MOTOROLA, MOTO, MOTOROLA SOLUTIONS, and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners.
    © 2011 and 2021 Motorola Solutions, Inc. All rights reserved.