Dell XPS 13 2-in-1 9310 2-in-1 Laptop User Manual

XPS 13 2-in-1 9310 2-in-1 Laptop

XPS 13 2-in-1 (9310 2n1)
Service Manual
Regulatory Model: P103G Regulatory Type: P103G002 September 2020 Rev. A00

Notes, cautions, and warnings
NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
© 2020 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks may be trademarks of their respective owners.

Contents

Chapter 1: Working inside your computer………………………………………………………………………….. 5 Before working inside your computer……………………………………………………………………………………………………………..5 Safety instructions………………………………………………………………………………………………………………………………………….. 5 Electrostatic discharge–ESD protection……………………………………………………………………………………………………… 6 ESD field service kit ………………………………………………………………………………………………………………………………………..6 Transporting sensitive components……………………………………………………………………………………………………………….. 7 After working inside your computer………………………………………………………………………………………………………………..7
Chapter 2: Removing and installing components………………………………………………………………… 8 Recommended tools……………………………………………………………………………………………………………………………………….. 8 Screw list…………………………………………………………………………………………………………………………………………………………. 8 Major components of XPS 13 2-in-1 (9310 2n1)……………………………………………………………………………………………..9 Base cover………………………………………………………………………………………………………………………………………………………. 11 Removing the base cover…………………………………………………………………………………………………………………………. 11 Installing the base cover……………………………………………………………………………………………………………………………13 Battery……………………………………………………………………………………………………………………………………………………………. 14 Lithium-ion battery precautions………………………………………………………………………………………………………………..14 Removing the battery………………………………………………………………………………………………………………………………. 15 Installing the battery………………………………………………………………………………………………………………………………….16 Display assembly……………………………………………………………………………………………………………………………………………..18 Removing the display assembly……………………………………………………………………………………………………………….. 18 Installing the display assembly………………………………………………………………………………………………………………….20 Speakers………………………………………………………………………………………………………………………………………………………… 22 Removing the speakers…………………………………………………………………………………………………………………………….22 Installing the speakers……………………………………………………………………………………………………………………………… 23 System board………………………………………………………………………………………………………………………………………………… 23 Removing the system board……………………………………………………………………………………………………………………. 23 Installing the system board……………………………………………………………………………………………………………………… 26 Keyboard assembly……………………………………………………………………………………………………………………………………….. 29 Removing the keyboard assembly…………………………………………………………………………………………………………… 29 Installing the keyboard assembly……………………………………………………………………………………………………………… 31 Palm-rest assembly………………………………………………………………………………………………………………………………………..34 Removing the palm-rest assembly………………………………………………………………………………………………………….. 34 Installing the palm-rest assembly……………………………………………………………………………………………………………. 34
Chapter 3: Drivers and downloads………………………………………………………………………………….. 36
Chapter 4: System setup………………………………………………………………………………………………. 37 BIOS overview………………………………………………………………………………………………………………………………………………..37 Entering BIOS setup program………………………………………………………………………………………………………………………..37 Navigation keys………………………………………………………………………………………………………………………………………………37 Boot Sequence……………………………………………………………………………………………………………………………………………….38 System setup options…………………………………………………………………………………………………………………………………….38 Clearing CMOS settings……………………………………………………………………………………………………………………………….. 47

Contents

Clearing BIOS (System Setup) and System passwords……………………………………………………………………………….47
Chapter 5: Troubleshooting……………………………………………………………………………………………48 Locate the Service Tag or Express Service Code of your Dell computer ……………………………………….48 Recovering the operating system………………………………………………………………………………………………………………… 48 SupportAssist | On-board Diagnostics…………………………………………………………………………………………………………. 48 System diagnostic lights………………………………………………………………………………………………………………………………..49 Flashing the BIOS…………………………………………………………………………………………………………………………………………..50 Flashing BIOS (USB key)……………………………………………………………………………………………………………………………… 50 WiFi power cycle…………………………………………………………………………………………………………………………………………… 50 Flea power release…………………………………………………………………………………………………………………………………………. 51
Chapter 6: Getting help and contacting Dell…………………………………………………………………….. 52

Contents

1
Working inside your computer
Before working inside your computer
About this task NOTE: The images in this document may differ from your computer depending on the configuration you ordered.
Steps 1. Save and close all open files and exit all open applications. 2. Shut down your computer. Click Start > Power > Shut down.
NOTE: If you are using a different operating system, see the documentation of your operating system for shut-down instructions.
3. Disconnect your computer and all attached devices from their electrical outlets. 4. Disconnect all attached network devices and peripherals, such as keyboard, mouse, and monitor from your computer.
CAUTION: To disconnect a network cable, first unplug the cable from your computer and then unplug the cable from the network device.
5. Remove any media card and optical disc from your computer, if applicable.
Safety instructions
Use the following safety guidelines to protect your computer from potential damage and to ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes that you have read the safety information that shipped with your computer.
WARNING: Before working inside your computer, read the safety information that is shipped with your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. WARNING: Disconnect your computer from all power sources before opening the computer cover or panels. After you finish working inside the computer, replace all covers, panels, and screws before connecting your computer to an electrical outlet.
CAUTION: To avoid damaging the computer, ensure that the work surface is flat, dry, and clean.
CAUTION: To avoid damaging the components and cards, handle them by their edges, and avoid touching the pins and the contacts. CAUTION: You should only perform troubleshooting and repairs as authorized or directed by the Dell technical assistance team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. See the safety instructions that is shipped with the product or at www.dell.com/regulatory_compliance. CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back of the computer. While you work, periodically touch an unpainted metal surface to dissipate static electricity which could harm internal components.

Working inside your computer

CAUTION: When you disconnect a cable, pull it by its connector or its pull tab, not the cable itself. Some cables have connectors with locking tabs or thumbscrews that you must disengage before disconnecting the cable. When disconnecting cables, keep them evenly aligned to avoid bending the connector pins. When connecting cables, ensure that the ports and the connectors are correctly oriented and aligned.
CAUTION: Press and eject any installed card from the media-card reader.
NOTE: The color of your computer and certain components may appear differently than shown in this document.
Electrostatic discharge–ESD protection
ESD is a major concern when you handle electronic components, especially sensitive components such as expansion cards, processors, memory DIMMs, and system boards. Very slight charges can damage circuits in ways that may not be obvious, such as intermittent problems or a shortened product life span. As the industry pushes for lower power requirements and increased density, ESD protection is an increasing concern.
Due to the increased density of semiconductors used in recent Dell products, the sensitivity to static damage is now higher than in previous Dell products. For this reason, some previously approved methods of handling parts are no longer applicable.
Two recognized types of ESD damage are catastrophic and intermittent failures. Catastrophic Catastrophic failures represent approximately 20 percent of ESD-related failures. The damage causes an
immediate and complete loss of device functionality. An example of catastrophic failure is a memory DIMM that has received a static shock and immediately generates a “No POST/No Video” symptom with a beep code emitted for missing or nonfunctional memory. Intermittent Intermittent failures represent approximately 80 percent of ESD-related failures. The high rate of intermittent failures means that most of the time when damage occurs, it is not immediately recognizable. The DIMM receives a static shock, but the tracing is merely weakened and does not immediately produce outward symptoms related to the damage. The weakened trace may take weeks or months to melt, and in the meantime may cause degradation of memory integrity, intermittent memory errors, etc.
The more difficult type of damage to recognize and troubleshoot is the intermittent (also called latent or “walking wounded”) failure.
Perform the following steps to prevent ESD damage: Use a wired ESD wrist strap that is properly grounded. The use of wireless anti-static straps is no longer allowed; they do
not provide adequate protection. Touching the chassis before handling parts does not ensure adequate ESD protection on parts with increased sensitivity to ESD damage. Handle all static-sensitive components in a static-safe area. If possible, use anti-static floor pads and workbench pads. When unpacking a static-sensitive component from its shipping carton, do not remove the component from the anti-static packing material until you are ready to install the component. Before unwrapping the anti-static packaging, ensure that you discharge static electricity from your body. Before transporting a static-sensitive component, place it in an anti-static container or packaging.
ESD field service kit
The unmonitored Field Service kit is the most commonly used service kit. Each Field Service kit includes three main components: anti-static mat, wrist strap, and bonding wire.
Components of an ESD field service kit
The components of an ESD field service kit are: Anti-Static Mat The anti-static mat is dissipative and parts can be placed on it during service procedures. When using an
anti-static mat, your wrist strap should be snug and the bonding wire should be connected to the mat and to any bare metal on the system being worked on. Once deployed properly, service parts can be removed from the ESD bag and placed directly on the mat. ESD-sensitive items are safe in your hand, on the ESD mat, in the system, or inside a bag. Wrist Strap and Bonding Wire The wrist strap and bonding wire can be either directly connected between your wrist and bare metal on the hardware if the ESD mat is not required, or connected to the anti-static mat to protect hardware that is temporarily placed on the mat. The physical connection of the wrist strap and bonding wire between your skin, the ESD

Working inside your computer

mat, and the hardware is known as bonding. Use only Field Service kits with a wrist strap, mat, and bonding wire. Never use wireless wrist straps. Always be aware that the internal wires of a wrist strap are prone to damage from normal wear and tear, and must be checked regularly with a wrist strap tester in order to avoid accidental ESD hardware damage. It is recommended to test the wrist strap and bonding wire at least once per week. ESD Wrist Strap Tester The wires inside of an ESD strap are prone to damage over time. When using an unmonitored kit, it is a best practice to regularly test the strap prior to each service call, and at a minimum, test once per week. A wrist strap tester is the best method for doing this test. If you do not have your own wrist strap tester, check with your regional office to find out if they have one. To perform the test, plug the wrist-strap’s bonding-wire into the tester while it is strapped to your wrist and push the button to test. A green LED is lit if the test is successful; a red LED is lit and an alarm sounds if the test fails. Insulator Elements It is critical to keep ESD sensitive devices, such as plastic heat sink casings, away from internal parts that are insulators and often highly charged. Working Environment Before deploying the ESD Field Service kit, assess the situation at the customer location. For example, deploying the kit for a server environment is different than for a desktop or portable environment. Servers are typically installed in a rack within a data center; desktops or portables are typically placed on office desks or cubicles. Always look for a large open flat work area that is free of clutter and large enough to deploy the ESD kit with additional space to accommodate the type of system that is being repaired. The workspace should also be free of insulators that can cause an ESD event. On the work area, insulators such as Styrofoam and other plastics should always be moved at least 12 inches or 30 centimeters away from sensitive parts before physically handling any hardware components ESD Packaging All ESD-sensitive devices must be shipped and received in static-safe packaging. Metal, static-shielded bags are preferred. However, you should always return the damaged part using the same ESD bag and packaging that the new part arrived in. The ESD bag should be folded over and taped shut and all the same foam packing material should be used in the original box that the new part arrived in. ESD-sensitive devices should be removed from packaging only at an ESD-protected work surface, and parts should never be placed on top of the ESD bag because only the inside of the bag is shielded. Always place parts in your hand, on the ESD mat, in the system, or inside an anti-static bag. Transporting Sensitive Components When transporting ESD sensitive components such as replacement parts or parts to be returned to Dell, it is critical to place these parts in anti-static bags for safe transport.
ESD protection summary
It is recommended that all field service technicians use the traditional wired ESD grounding wrist strap and protective anti-static mat at all times when servicing Dell products. In addition, it is critical that technicians keep sensitive parts separate from all insulator parts while performing service and that they use anti-static bags for transporting sensitive components.
Transporting sensitive components
When transporting ESD sensitive components such as replacement parts or parts to be returned to Dell, it is critical to place these parts in anti-static bags for safe transport.
After working inside your computer
About this task
CAUTION: Leaving stray or loose screws inside your computer may severely damage your computer.
Steps
1. Replace all screws and ensure that no stray screws remain inside your computer. 2. Connect any external devices, peripherals, or cables you removed before working on your computer. 3. Replace any media cards, discs, or any other parts that you removed before working on your computer. 4. Connect your computer and all attached devices to their electrical outlets. 5. Turn on your computer.

Working inside your computer

Removing and installing components

NOTE: The images in this document may differ from your computer depending on the configuration you ordered.

Recommended tools

The procedures in this document may require the following tools:
Phillips screwdriver #00 Phillips screwdriver #0 Torx screwdriver T5 Flat-head screwdriver Plastic scribe

Screw list

NOTE: When removing screws from a component, it is recommended to note the screw type, the quantity of screws, and then place them in a screw storage box. This is to ensure that the correct number of screws and correct screw type is restored when the component is replaced.
NOTE: Some computers have magnetic surfaces. Ensure that the screws are not left attached to such surfaces when replacing a component.

NOTE: Screw color may vary with the configuration ordered.

Table 1. Screw list Component Base cover

Secured to Palm-rest assembly

Screw type M2x4.5

Quantity 8 Torx screws

Screw image

Battery

System board

Battery

Palm-rest assembly

Battery

Palm-rest assembly

Display-cable bracket System board

Display assembly

Palm-rest assembly

USB Type-C bracket

System board

USB Type-C bracket

System board

M1.6×3.4 M1.6×3 M1.2×4 M1.6×3 M2.5×3 M1.6×3 M1.6×2

1 Torx screw
7 2 1 captive screw on display-cable bracket 4
1 1

Removing and installing components

Table 1. Screw list (continued)

Component

Secured to

System board

Palm-rest assembly

System board

Palm-rest assembly

System board

Palm-rest assembly

Keyboard assembly Keyboard assembly

Palm-rest assembly Palm-rest assembly

Screw type M1.6×2.5
M1.2×3

Quantity 4
3

M1.2×4

1 captive screw

M1.2×1.4

M1.2×1.6

Screw image

Major components of XPS 13 2-in-1 (9310 2n1)
The following image shows the major components of XPS 13 2-in-1 (9310 2n1).

Removing and installing components

1. Base cover 2. Battery 3. System board 4. Left fan 5. Left keyboard bracket

Removing and installing components

6. Palm-rest assembly 7. Left speaker 8. Display assembly 9. Right speaker 10. Keyboard assembly 11. USB Type-C port bracket 12. Right fan
NOTE: Dell provides a list of components and their part numbers for the original system configuration purchased. These parts are available according to warranty coverages purchased by the customer. Contact your Dell sales representative for purchase options.
Base cover
Removing the base cover
Prerequisites 1. Follow the procedure in Before working inside your computer.
About this task The following images indicate the location of the base cover and provide a visual representation of the removal procedure.

Removing and installing components

Steps 1. Remove the eight Torx screws (M2x4.5) that secure the base cover to the palm-rest assembly. 2. Starting from the bottom-left corner, pry the base cover in the direction of the arrows to release it from the palm-rest
assembly. CAUTION: Do not pull on or pry the base cover from the top as it may damage the base cover.
3. Hold both sides of the base cover and rotate from front to back to remove from palm rest assembly. NOTE: The pins at the bottom of the base cover for grounding the antennas and the audio board are fragile. Place the base cover on a clean surface to avoid damage to the pins.
Installing the base cover
Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure.
About this task The following images indicate the location of the base cover and provide a visual representation of the installation procedure.

Removing and installing components

Steps 1. Align and secure the back of the base cover on the palm-rest assembly, and then snap the base cover into place. 2. Replace the eight Torx screws (M2x4.5) that secure the base cover to the palm-rest assembly.
Next steps 1. Follow the procedure in After working inside your computer.
Battery
Lithium-ion battery precautions
CAUTION: Exercise caution when handling Lithium-ion batteries. Discharge the battery completely before removing it. Disconnect the AC power adapter from the system and
operate the computer solely on battery power–the battery is fully discharged when the computer no longer turns on when the power button is pressed. Do not crush, drop, mutilate, or penetrate the battery with foreign objects. Do not expose the battery to high temperatures, or disassemble battery packs and cells.

Removing and installing components

Do not apply pressure to the surface of the battery. Do not bend the battery. Do not use tools of any kind to pry on or against the battery. Ensure any screws during the servicing of this product are not lost or misplaced, to prevent accidental
puncture or damage to the battery and other system components. If the battery gets stuck inside your computer as a result of swelling, do not try to release it as puncturing,
bending, or crushing a lithium-ion battery can be dangerous. In such an instance, contact Dell technical support for assistance. See www.dell.com/contactdell. Always purchase genuine batteries from www.dell.com or authorized Dell partners and resellers.
Removing the battery
Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the base cover.
About this task The following image indicates the location of the battery and provides a visual representation of the removal procedure.

Removing and installing components

Steps 1. Remove the Torx 5 screw (M1.6×3.4) that secures the battery cable to the system board. 2. Disconnect the battery cable from the interposer board.
NOTE: Remove the interposer board immediately after disconnecting the battery cable to avoid misplacing it. Hold the edges of the interposer board to avoid damaging the pins on it.
NOTE: The interposer board is not polarity sensitive and both sides are compatible.
3. Remove the interposer board from the system board. 4. Remove the seven screws (M1.6×3) that secure the battery to the palm-rest assembly. 5. Remove the two screws (M1.2×4) that secure the battery to the system board. 6. Lift the battery off the palm-rest assembly. 7. Turn the battery over. 8. Using a plastic scribe, push to remove the magnet and the metal bar from the battery.
NOTE: Keep the magnet and the metal bar as they need to be installed on the new battery.
Installing the battery
Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure.
About this task The following image indicates the location of the battery and provides a visual representation of the installation procedure.

Removing and installing components

Steps 1. Adhere the magnet and the metal bar to the battery.
NOTE: Install the magnet and the metal bar from the faulty battery.
2. Align the screw holes on the battery with the screw holes on the system board and palm-rest assembly. 3. Replace the two screws (M1.2×4) that secure the battery to the system board. 4. Replace the seven screws (M1.6×3) that secure the battery to the palm-rest assembly. 5. Place the interposer board to the connector on the system board.
NOTE: The interposer board is not polarity sensitive and both sides are compatible.
6. Connect the battery cable to the interposer board. 7. Replace the Torx 5 screw (M1.6×3.4) that secures the battery cable to the system board.
Next steps 1. Install the base cover. 2. Follow the procedure in After working inside your computer.

Removing and installing components

Display assembly
Removing the display assembly
Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the base cover. 3. Remove the battery.
About this task The following images indicate the location of display assembly and provide a visual representation of the removal procedure.

Removing and installing components

Steps
1. Loosen the captive screw (M1.6×3) that secures the display-cable bracket to the system board. 2. Lift the display-cable bracket off the system board. 3. Peel the tapes that secure the display cable and camera cable to the system board. 4. Using the tape as a pull tab, disconnect the display cable and camera cable from the system board. 5. Remove the display cable and camera cable from the routing guides on the system board. 6. Remove the four screws (M2.5×3) that secure the display hinges to the palm-rest assembly. 7. Slide the palm-rest assembly off the display assembly.

Removing and installing components

Installing the display assembly
Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure.
About this task The following images indicate the location of display assembly and provide a visual representation of the installation procedure.

Removing and installing components

Steps
1. Slide the palm-rest assembly under the display assembly. 2. Align the screw holes on the palm-rest assembly with the screw holes on the display hinges. 3. Replace the four screws (M2.5×3) that secure the display hinges to the palm-rest assembly. 4. Route the display cable and camera cable through the routing guides on the system board.

Removing and installing components

5. Connect the display cable and camera cable to the system board. 6. Adhere the tapes that secure the display cable and camera cable to the system board. 7. Align and place the display-cable bracket on the system board. 8. Tighten the captive screw (M1.6×3) that secures the display-cable bracket to the system board.
Next steps 1. Install the battery. 2. Install the base cover. 3. Follow the procedure in After working inside your computer.
Speakers
Removing the speakers
Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the base cover. 3. Remove the battery.
About this task The following image indicates the location of speakers and provides a visual representation of the removal procedure.

Steps
1. Disconnect the speaker cable from the system board. 2. Note the routing of the speaker cable and remove the speaker cable from the routing guides on the palm-rest assembly. 3. Using a plastic scribe, pry the speakers off the palm-rest assembly.

Removing and installing components

Installing the speakers
Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure.
About this task The following image indicates the location of speakers and provides a visual representation of the installation procedure.

Steps 1. Slide the speakers into the slots on the palm-rest assembly.
NOTE: Ensure that there is no adhesive residue from the faulty speakers that are removed previously.
2. Route the speaker cable through the routing guides on the palm-rest assembly. 3. Connect the speaker cable to the system board.
Next steps 1. Install the battery. 2. Install the base cover. 3. Follow the procedure in After working inside your computer.
System board
Removing the system board
Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the base cover. 3. Remove the battery.

Removing and installing components

About this task The following image indicates the connectors on your system board.

Figure 1. System-board connectors
1. Speaker cable 3. Display cable 5. Keyboard-controller board cable

2. Fingerprint-reader cable 4. Camera cable

The following images indicate the location of system board and provide a visual representation of the removal procedure.

Removing and installing components

5. Remove the display cable and camera cable from the routing guides on the system board. 6. Remove the screw (M1.6×3) and the screw (M1.6×2) that secures the type-C bracket to the system board.
NOTE: The M1.6×2 screw has a bigger head than the M1.6×3 screw.
7. Lift the type-C bracket off the system board. 8. Disconnect the speaker cable from the system board. 9. Open the latch and disconnect the fingerprint-reader cable from the system board. 10. Peel off the fingerprint-reader daughter-board from the system board. 11. Open the latch and disconnect the keyboard-controller board cable from the system board. 12. Remove the four screws (M1.6×2.5), three screws (M1.2×3), and one captive screw (M1.2×4) that secure the system board
to the palm-rest assembly. 13. Lift the system board off the palm-rest assembly. 14. Remove the power-button and fingerprint reader bracket from the palm-rest assembly. 15. Place the bracket and the system board on a dry, flat, and clean surface.
Installing the system board
Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure.
About this task The following image indicates the connectors on your system board.

Figure 2. System-board connectors
1. Speaker cable 3. Display cable 5. Keyboard-controller board cable

2. Fingerprint-reader cable 4. Camera cable

The following images indicate the location of system board and provide a visual representation of the installation procedure.

Removing and installing components

Steps 1. Align and place the power-button and fingerprint reader bracket on the palm-rest assembly. 2. Align the screw holes on the system board with the screw holes on the palm-rest assembly. 3. Replace the fours screws (M2x4), three screws (M1.2×3), and one screw (M1.2×4) that secure the system board to the
palm-rest assembly. 4. Connect the keyboard-controller board cable to the system board and close the latch to secure the cable. 5. Connect the speaker cable to the system board. 6. Adhere the fingerprint-reader board to the slot on the system board. 7. Connect the fingerprint-reader cable to the system board and close the latch to secure the cable. 8. Align the screw holes on the USB Type-C bracket to the screw holes on the system board. 9. Replace the screw (M1.6×3) and the screw (M1.6×2) that secures the USB Type-C port bracket to the system board.
NOTE: The M1.6×2 screw has a bigger head than the M1.6×3 screw.
10. Route the display cable and camera cable through the routing guides on the system board. 11. Connect the display cable and camera cable to the system board.

Removing and installing components

12. Adhere the tapes that secure the display cable and camera cable to the system board. 13. Align and place the display-cable bracket on the system board. 14. Tighten the captive screw (M1.6×3) that secures the display-cable bracket to the system board.
Next steps 1. Install the battery. 2. Install the base cover. 3. Follow the procedure in After working inside your computer.
Keyboard assembly
Removing the keyboard assembly
Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the base cover. 3. Remove the battery. 4. Remove the system board.
About this task The following images indicate the location of keyboard assembly and provide a visual representation of the removal procedure.

Removing and installing components

Steps 1. Peel the fingerprint reader cable from the keyboard. 2. Remove the speaker cable from the routing guides on the left keyboard bracket. 3. Loosen the captive screw that secures the left keyboard bracket to the palm-rest assembly. 4. Using a plastic scribe, pry the left keyboard bracket off the palm-rest assembly. 5. Loosen the captive screw that secures the right keyboard bracket to the palm-rest assembly. 6. Using a plastic scribe, pry the right keyboard bracket off the palm-rest assembly. 7. Disconnect the keyboard cable and keyboard backlight cable from the keyboard controller board. 8. Peel the keyboard controller board cable from the keyboard. 9. Remove the 38 screws (M1.2×1.4) and ten screws (M1.2×1.6) that secure the keyboard to the palm-rest assembly.
NOTE: Peel off the three copper foil from the palm-rest assembly, and then peel off the two conductive tapes on the keyboard assembly to separate the keyboard assembly and the palm-rest assembly.
10. Lift the keyboard off the palm-rest assembly.
Installing the keyboard assembly
Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure.
About this task The following images indicate the location of keyboard assembly and provide a visual representation of the installation procedure.

Removing and installing components

Steps 1. Align the screw holes on the keyboard with the screw holes on the palm-rest assembly.
NOTE: Adhere the two conductive tapes on the keyboard, and then adhere the three copper foils on the palm-rest assembly to secure the keyboard assembly to the palm-rest assembly.
2. Replace the 38 screws (M1.2×1.4) and ten screws (M1.2×1.6) that secure the keyboard to the palm-rest assembly. NOTE: Do not install keyboard assembly screws into locations that are marked with MB. Those screw holes are reserved for system board screws.
3. Adhere the keyboard controller board cable to the keyboard. 4. Connect the keyboard cable and keyboard backlight cable to the keyboard controller board. 5. Adhere the right keyboard bracket in the slots on the palm-rest assembly. 6. Tighten the captive screw that secures the right keyboard bracket to the palm-rest assembly. 7. Adhere the right keyboard bracket in the slots on the palm-rest assembly. 8. Tighten the captive screw that secures the left keyboard bracket to the palm-rest assembly. 9. Route the speaker cable through the routing guides on the left keyboard assembly. 10. Adhere the fingerprint reader cable to the keyboard.
Next steps 1. Install the system board. 2. Install the battery. 3. Install the base cover. 4. Follow the procedure in After working inside your computer.

Removing and installing components

Palm-rest assembly
Removing the palm-rest assembly
Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the base cover. 3. Remove the battery. 4. Remove the display assembly. 5. Remove the speakers. 6. Remove the system board. 7. Remove the keyboard assembly.
About this task The following image indicates the palm-rest assembly and provides a visual representation of the removal procedure.

Steps The palm-rest assembly is left after performing the steps in the prerequisites.
NOTE: Keep the power-button and fingerprint reader bracket if you must replace the palm-rest assembly as the bracket is a separate service part for reuse.
NOTE: If the power-button and fingerprint reader bracket is not found on the palm-rest assembly, the bracket should be on the system board.
Installing the palm-rest assembly
Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure.

Removing and installing components

About this task The following image indicates the palm-rest assembly and provides a visual representation of the installation procedure.

Steps Place the palm-rest assembly on a flat surface.
NOTE: If you are installing components to a new palm-rest assembly, use the power-button and fingerprint reader bracket from the previous palm-rest assembly.
Next steps 1. Install the keyboard assembly. 2. Install the system board . 3. Install the speakers. 4. Install the display assembly. 5. Install the battery. 6. Install the base cover. 7. Follow the procedure in After working inside your computer.

Removing and installing components

3
Drivers and downloads
When troubleshooting, downloading or installing drivers it is recommended that you read the Dell Knowledge Based article, Drivers and Downloads FAQ SLN128938.

Drivers and downloads

System setup

CAUTION: Unless you are an expert computer user, do not change the settings in the BIOS Setup program. Certain changes can make your computer work incorrectly.
NOTE: Depending on the computer and its installed devices, the items listed in this section may or may not be displayed.
NOTE: Before you change BIOS Setup program, it is recommended that you write down the BIOS Setup program screen information for future reference.
Use the BIOS Setup program for the following purposes: Get information about the hardware installed in your computer, such as the amount of RAM and the size of the hard drive. Change the system configuration information. Set or change a user-selectable option, such as the user password, type of hard drive installed, and enabling or disabling
base devices.

BIOS overview
The BIOS manages data flow between the computer’s operating system and attached devices such as hard disk, video adapter, keyboard, mouse, and printer.

Entering BIOS setup program

About this task Turn on (or restart) your computer and press F2 immediately.

Navigation keys

NOTE: For most of the System Setup options, changes that you make are recorded but do not take effect until you restart the system.

Table 2. Navigation keys Keys Up arrow Down arrow Enter
Spacebar Tab

Navigation Moves to the previous field. Moves to the next field. Selects a value in the selected field (if applicable) or follow the link in the field. Expands or collapses a drop-down list, if applicable. Moves to the next focus area.
NOTE: For the standard graphics browser only.

Esc

Moves to the previous page until you view the main screen.

Pressing Esc in the main screen displays a message that

prompts you to save any unsaved changes and restarts the

system.

System setup

Boot Sequence
Boot Sequence allows you to bypass the System Setupdefined boot device order and boot directly to a specific device (for example: optical drive or hard drive). During the Power-on Self Test (POST), when the Dell logo appears, you can:
Access System Setup by pressing F2 key Bring up the one-time boot menu by pressing F12 key The one-time boot menu displays the devices that you can boot from including the diagnostic option. The boot menu options are:
Removable Drive (if available) STXXXX Drive (if available)
NOTE: XXX denotes the SATA drive number.
Optical Drive (if available) SATA Hard Drive (if available) Diagnostics The boot sequence screen also displays the option to access the System Setup screen.

System setup options

NOTE: Depending on this computer and its installed devices, the items that are listed in this section may or may not be displayed.
Table 3. System setup options–System information menu Overview

BIOS Version Service Tag Asset Tag Ownership Tag Manufacture Date Ownership Date Express Service Code Ownership Tag Signed Firmware Update Battery Primary Battery Level Battery State Health AC Adapter Processor Information Processor Type Maximum Clock Speed Core Count Processor L2 Cache Processor ID

Displays the BIOS version number. Displays the Service Tag of the computer. Displays the Asset Tag of the computer. Displays the ownership tag of the computer. Displays the manufacture date of the computer. Displays the ownership date of the computer. Displays the express service code of the computer. Displays the ownership tag of the computer. Displays whether the signed firmware update is enabled. Displays the battery health information. Displays the primary battery. Displays the battery level. Displays the battery state. Displays the battery health. Displays whether an AC adapter is installed.
Displays the processor type. Displays the maximum processor clock speed. Displays the number of cores on the processor. Displays the processor L2 Cache size. Displays the processor identification code.

System setup

Table 3. System setup options–System information menu (continued)

Overview

Processor L3 Cache

Displays the processor L3 Cache size.

Current Clock Speed

Displays the current processor clock speed.

Minimum Clock Speed

Displays the minimum processor clock speed.

Microcode Version

Displays the microcode version.

Intel Hyper-Threading Capable

Displays whether the processor is Hyper-Threading (HT) capable.

64-Bit Technology

Displays whether 64-bit technology is used.

Memory Information

Memory Installed

Displays the total computer memory installed.

Memory Available

Displays the total computer memory available.

Memory Speed

Displays the memory speed.

Memory Channel Mode

Displays single or dual channel mode.

Memory Technology

Displays the technology that is used for the memory.

Device Information

Video Controller

Displays the integrate graphics information of the computer.

Video BIOS Version

Displays the video BIOS version of the computer.

Video Memory

Displays the video memory information of the computer.

Panel Type

Displays the Panel Type of the computer.

Native Resolution

Displays the native resolution of the computer.

Audio Controller

Displays the audio controller information of the computer.

Wi-Fi Device

Displays the wireless device information of the computer.

Bluetooth Device

Displays the Bluetooth device information of the computer.

Table 4. System setup options–Boot options menu

Boot options

Advanced Boot Options Enable UEFI Network Stack

Enables or disables UEFI Network Stack. Default: OFF.

Boot Mode Boot Mode: UEFI only Enable Boot Devices Boot Sequence BIOS Setup Advanced Mode

Displays the boot mode of this computer. Enables or disables boot devices for this computer. Displays the boot sequence. Enables or disables advanced BIOS settings. Default: ON.

UEFI Boot Path Security

Enables or disables the system to prompt the user to enter the Admin password when booting a UEFI boot path from the F12 boot menu.
Default: Always Except Internal HDD.

Table 5. System setup options–System Configuration menu System Configuration
Date/Time

System setup

Table 5. System setup options–System Configuration menu (continued)

System Configuration Date
Time
Storage Interface Port Enablement SATA Operation

Sets the computer date in MM/DD/YYYY format. Changes to the date take effect immediately. Sets the computer time in HH/MM/SS 24-hour format. You can switch between 12-hour and 24-hour clock. Changes to the time take effect immediately.
Enables the selected onboard drives. Configures operating mode of the integrated SATA hard drive controller. Default: RAID. SATA is configured to support RAID (Intel Rapid Restore Technology).

Drive Information Enable Audio

Displays the information of various onboard drives. Enables or disables all integrated audio controller. Default: ON.

Enable Microphone

Enables or disables microphone. Default: ON.

Enable Internal Speaker

Enables or disables internal speaker. Default: ON.

USB Configuration Enable Boot Support

Enables or disables booting from USB mass storage devices such as external hard drive, optical drive, and USB drive.
Default: ON.

Enable External USB Ports

Enables or disables USB ports to be functional in an operating system environment.
Default: ON.

Enable Thunderbolt Technology Support Enables or disables Thunderbolt Technology Support. Default: ON.

Enable Thunderbolt Boot Support

Enables or disables Thunderbolt Boot Support. Default: OFF.

Miscellaneous Devices Enable Camera

Enables or disables various onboard devices. Enables or disables the camera. Default: ON.

Touchscreen

Enables or disables the touchscreen for the operating system. NOTE: Touchscreen will always work in the BIOS setup irrespective of this setting.
Default: ON.

Enable Fingerprint Reader Device

Enables or disables the Fingerprint Reader Device. Default: ON.

Enable Fingerprint Reader Single Sign On Enables or disables the Fingerprint Reader Device’s Single Sign On capability. Default: ON.

Enable MediaCard

Enables to switch all media cards On/Off or set the media card to read-only state.

System setup

Table 5. System setup options–System Configuration menu (continued)

System Configuration

Default: Enable Secure Digital (SD) Card.

Keyboard Illumination

Configures the operating mode of the keyboard illumination feature.
Default: Bright. Enable the keyboard illumination feature at 100% brightness level.

Keyboard Backlight Timeout on AC

Configures the timeout value for the keyboard when an AC adapter is connected to the computer. The keyboard backlight timeout value is only effect when the backlight is enabled.
Default: 10 seconds.

Keyboard Backlight Timeout on Battery

Configures the timeout value for the keyboard when the computer is running on battery. The keyboard backlight timeout value is only effect when the backlight is enabled.
Default: 10 seconds.

Table 6. System setup options–Video menu

Video

LCD Brightness

Brightness on battery power

Sets the screen brightness when the computer is running on battery power.

Brightness on AC power

Sets the screen brightness when the computer is running on AC power.

Table 7. System setup options–Security menu

Security

Enable Admin Setup Lockout

Enables or disables the user from entering BIOS Setup when an Admin Password is set.

Default: OFF.

Password Bypass

Bypass the System (Boot) Password and the internal hard drive password prompts during a system restart.
Default: Disabled.

Enable Non-Admin Password Changes

Enables or disables the user to change the system and hard drive password without the need for admin password.
Default: ON.

Non-Admin Setup Changes Allow Wireless Switch Changes

Enables or disables changes to the setup option when an Administrator password is set.
Default: OFF.

Enable UEFI Capsule Firmware Updates Absolute

Enables or disables BIOS updates through UEFI capsule update packages.
Enables, disables or permanently disable the BIOS module interface of the optional Absolute Persistence Module service from Absolute Software.
Default: Enable Absolute.

TPM 2.0 Security On

Select whether or not the Trusted Platform Model (TPM) is visible to the OS. Default: ON.

PPI Bypass for Enable Commands

Enables or disables the OS to skip BIOS Physical Presence Interface (PPI) user prompts when issuing TPM PPI enabled and activate commands.
Default: OFF.

System setup

Table 7. System setup options–Security menu (continued)

Security

PPI Bypass for Disable Commands

Enables or disables The OS to skip BIOS PPI user prompts when issuing TPM PPI Disable and Deactivate commands.

Default: OFF.

PPI Bypass for Clear Commands

Enables or disables the operating system to skip BIOS Physical Presence Interface (PPI) user prompts when issuin

Download

Dell XPS 13 2-in-1 9310 2-in-1 Laptop User Manual

Was this manual helpful?