Motorola Multi-Unit Charger Kits Instructions

MAINTENANCE MULTI-UNIT CHARGER KITS
PMPN4308/PMPN4309/PMPN4310/
PMPN4311/PMPN4312/PMPN4319/
PMPN4320/PMPN4321/PMPN4322
QUICK START GUIDE

Important Safety Instructions

This document contains important safety and operating instructions. Please read these instructions carefully and save them for future reference. Before using the battery charger, read all the instructions and cautionary markings on (1) the charger and (2) the battery.

1. To reduce the risk of damage to the power cords, pull the plug rather than the! cord when disconnecting from the AC outlet or the charger.
2. An extension cord should not be used unless absolutely necessary. Use W A R N I N G of an improper extension cord could result in a risk of fire and electric shock. If an extension cord must be used, make sure that the cord size is 18 AWG for lengths of up to 6.5 feet (2.0 m), and 16 AWG for lengths up to 9.8 feet (3.0 m).
3. To reduce the risk of fire, electric shock, or injury, do not operate the charger if it has been broken or damaged in any way. Take it to a qualified Motorola Solutions service representative.
4. Do not disassemble the charger. It is not repairable and replacement parts are not available. Disassembly of the charger may result in a risk of electric shock or fire.
5. To reduce the risk of electric shock, unplug the charger power cord from the AC outlet before attempting any maintenance or cleaning.
6. To reduce the risk of injury, charge only the rechargeable Motorola Solutions authorized batteries listed in Table 4. Other batteries may explode, causing personal injury and damage.
7. Use of accessories not recommended by Motorola Solutions may result in a risk of fire, electric shock, or injury.

Operational Safety Guidelines

•  This equipment is not suitable for outdoor use. Use only in dry locations and conditions.
• Maximum ambient temperature around the charger must not exceed 40 °C (104 °F).
• Connect the charger to the power supply listed in Table 2 with an appropriate power cord listed in Table 3.
• The AC outlet to which the power cord is connected should be closed and easily accessible.
• Make sure the power cord is located where it will not be stepped on, tripped over, or subjected to water, damage, or stress.
• Connect the power cord only to an appropriately fused and wired AC outlet with the correct voltage, as specified on the product.
• Disconnect from line voltage by removing the power cord from the AC outlet.
• The Maintenance Charger charges the batteries listed in Table 4.

Table 1: Multi-Unit Charger

Table 2: Motorola Solutions Authorized Power Supply

Table 3: Motorola Solutions Authorized Power Cords

Table 3: Motorola Solutions Authorized Power Cords (Continued)

Table 4: Motorola Solutions Authorized Batteries

Charger Overview

Figure 1: Charger Overview

Table 5: Charger Overview and Description

Operating Instructions

• Batteries charge best at room temperature.
• DO NOT leave batteries in the charger after charging is complete.

Charging Procedure

Figure 2: Charging Procedure

1.  Place the Multi-Unit Charger (MUC) on a flat surface.
2. Firmly insert the power supply into the charger DC Inlet Socket at the back of the charger.
3. Plug the power supply power cord into a matching power outlet.
4. Upon successful power-up, each pocket LED shows Green for one second and
   IMPRES 2 MAINTENANCE CHGR is displayed. If the LEDs do not flash and no message is displayed, check power cord connections.
5. Insert the battery into an available pocket.
6. When the battery is properly seated in the pocket:
   – Charging status of a battery is indicated by the LED Status Indicator of the associated pocket on the MUC.
   – The Display of the MUC shows the charging status of Pocket 1 only.
7. The battery is ready when LED is Steady Green (for non-IMPRES or non-IMPRES 2
   Motorola Solutions battery) or Alternating Amber/Green (for IMPRES or IMPRES 2 Motorola Solutions battery).

Display Messages and Led Indications

Table 6: IMPRES 2™ or IMPRES™ Battery for Long-Term Storage

Table 7: Other Motorola Solutions Batteries for Long-Term Storage

Table 8: IMPRES 2™ or IMPRES™ Lithium-ion Battery for Shipment

Table 9: Other Motorola Solutions Lithium-ion Batteries for Shipment

Optional equipment
A wall mount bracket (Part Number BR000271A01) is available for the Multi-Unit Charger (MUC). Contact your local dealer to order this item. Installation of the wall mount bracket is as follows:

Figure 3: Mounting Multi-Unit Charger to Wall Bracket

Mounting Multi-Unit Charger to Wall Bracket

1. Position the wall mount bracket in the desired position, and mark the location of the mounting holes on the wall surface.
   Ensure the area behind the mounting surface is always free of electrical wires, cables, and pipes before cutting, drilling, or installing the mounting screws.
2. Mount bracket to wall using the appropriate mounting hardware required for the type of wall material fixture it is being mounted to. Drill based on the marked mounting holes on the wall surfaces.
3. Secure the wall bracket in position by installing mounting hardware over the mounting holes on the wall bracket tightly.
   Note: It is recommended to use 10-16×1-1/2” tapping screw and washer (not included) on wood stud and solid-flat concrete/brick wall.
4. Hang the MUC on wall bracket as shown in Figure 3.

Additional Features and Information
The complete online user guide is available through publication part number MN003725A01 at  https://www.motorolasolutions.com/content/learning/en_us/documentation-portal/accessories-_-energy/chargers.html. This guide provides information on features of the IMPRES 2™ Maintenance Multi-Unit Chargers.

EU Contact:
Motorola Solutions, Czerwone Maki 82,
30-392 Krakow, Poland.

MOTOROLA, MOTO, MOTOROLA SOLUTIONS, and the Stylized M Logo are trademarks or
registered trademarks of Motorola Trademark Holdings, LLC and are used under license.
All other trademarks are the property of their respective owners.
© 2017 and 2020 Motorola Solutions, Inc. All rights reserved.

Printed in