Honeywell T6R-HW Smart Thermostat Installation Guide
T6R-HW SMART THERMOSTAT
Need help? For assistance please visit: getconnected.honeywellhome.com Resideo, 200 Berkshire Place, Winnersh Triangle, Berkshire RG41 5R Phone: 0300 130 1299
Approvals
Hereby, Pittway Sarl declares that the radio equipment type T6R-HW is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://hwllhome.co/DoC
RF (868MHz): Receiver Category 2, Max RF Power 25mW, 868868.6MHz (868.3MHz)
Wi-Fi (2.4GHz): Max Power 100mW, 2.42.458GHz
ErP: Class V (+3%), (EU) 811/2013
Read these instructions carefully. Failure to follow these instructions can damage the product or cause a hazardous condition.
Turn OFF the power and remove the old thermostat
To ensure your safety, always make sure mains power is switched OFF before accessing wiring.
In case of removing the old thermostat be aware that the existing wiring will no longer be used
The T6R-HW thermostat should not be placed near draughts, in direct sunlight or near heat sources.
WEEE Directive 2012/19/EC
Waste Electrical and Electronic Equipment directive
At the end of the product, life disposes of the packaging and product in a corresponding recycling center. Do not dispose of the unit with the usual domestic refuse. Do not burn the product.
Prepare Receiver Box for installation
Before installation of the
Receiver Box
housing.
Loosen the front screw to remove the cover or tighten it when the cover is back in place.
Needed during installation:
- Cable with 2 wires from the boiler to Receiver Box.
- The Receiver Box requires 230V power
Install the Receiver Box
A) Wall box or Rear Wiring
Hinge open the terminal block flap to access the cables and wall box screw holes. |
B) Surface wiring
Use the cable clamps to secure the surface wiring. |
C) Replace the cover
Locate the hinges at the top of the cover and wall plate, close the cover and secure with the screw. |
Install the T6 thermostat
Choose the appropriate plug.
Place the thermostat on an even, horizontal surface and plug it in.
Complete installation
Turn ON mains power to the Heating Appliance and Receiver Box. No binding is needed, the Receiver Box and Thermostat are pre-bound.
The LED on the receiver box will blink yellow to indicate the box is in binding mode. On the thermostat press
Set Up and configuration
1) Touch setting up the thermostat. |
2) Select your language. | 3) Set the clock format, time and date. |
4) Touch |
Once setup is completed, if you need to change more settings go to the advanced menu. To access the advanced menu
press
Menu Item | Default | Options |
LANGUAGE | English | 0 = English, 1 = Français, 2 = Español 3 = Deutsch, 4 = Nederlands, 5 = Italiano |
SYSTEM TYPE | Heat+HW | Heating only, Heating + Hot Water, Heating + Cooling |
OPENTHERM | – | OpenTherm boiler data when available |
CYCLE RATE | 6 | 3, 6, 9 or 12 |
MINIMUM ON TIME | 1 minute | 1, 2, 3, 4 or 5 minutes |
HEAT RANGE | Min = 5.0ºC Max = 35.0ºC |
1 = Daily schedule, 2 = 5+2 days schedule |
SCHEDULE OPTIONS | Daily | Min: 5ºC to 21ºC, Max: 21ºC to 35ºC |
OPTIMISE | Opt. start OFF Opt. stop OFF |
Opt. start: 0 = off, 1 = on, 2 = Delayed start Opt. stop: 0 = off, 1 = on |
CLOCK | Format: 24h Time: –:-Date: 01/09/16 |
Clock format: 1 = 12h, 2 = 24h Setup time and date |
LOW LOAD CONTROL | ON | 0 = off, 1 = on |
TEMPERATURE OFFSET | 0.0ºC | 1.5 ºC to 1.5ºC |
BINDING | – | Bind, check RF, and clear bind. |
RESET | – | Factory, schedule, WiFi, and HomeKit reset |
FAILSAFE | OFF | 0 = off, 1 = on |
Wiring Diagrams
A) Sundial S-plan
B) Sundial Y-plan
C) Combi boiler
D) OpenTherm boiler
For other wiring diagrams visit:
http://www.honeywelluk.com/professional-zone/resource-centre/Wiring-Diagrams/
https://hwllhome.co/uk-wiring
* See boiler specifications for correct terminals
www.resideo.com
Pittway Sarl, Z.A. La Pièce 4,
1180 Rolle, Switzerland
Country of origin: UK
© 2020 Resideo Technologies, Inc. All rights reserved.
The Honeywell Home trademark is used under license from Honeywell International Inc.
This product is manufactured by Resideo Technologies, Inc. and its affiliates.