Sony MDR-Z1R Stereo Headphones User Guide
Stereo Headphones
MDR-Z1R
How to Use
- Gr ab the rubber part of the plug, insert the plug firmly until it clicks, then fasten the rotating part.
- Rotating part
- Plug
- L jack (silver)
- Tactile dot
- R jack (red)
- Red
- Silver
- Balanced-connection headphone cable (1.2 m)
- Headphone cable (3 m)
- L-type balanced standard plug
• You can connect devices that are compatible with the balanced standard plug, such as WALKMAN®, headphone amplifiers, etc. - WALKMAN® NW-WM1Z (sold separately), NW-WM1A (sold separately)
- Headphone amplifier TA-ZH1ES (sold separately)
- Stereo mini-plug
- Unmatched plug adaptor
- Headphones
- Hard case
- Open
- Close
- Headphone cable × 2
Specifications
Type: Closed, dynamic (circum-aural) / Driver unit: 70 mm, dome type (CCAW Voice Coil) / Power handling capacity: 2,500 mW (IEC*) / mpedance: 64 Ω at 1 kHz / Sensitivity: 100 dB/mW / Frequency response: 4 Hz – 120,000 Hz / Mass: Approx.
385 g (14 oz) without cable / Included items: Stereo headphones (1), Headphone cable (Approx. 3 m (118 1/8 in), silver-coated OFC strands, gold-plated stereo mini-plug) (1), Balanced-connection headphone cable (Approx. 1.2 m (47 1/4 in), silver-coated OFC strands, Gold plated balanced
standard plug) (1), Gold-plated unmatch plug adaptor (stereo phone plug
* IEC = International Electrotechnical commission
Design and specifications are subject to change without notice.
WALKMAN® and WALKMAN® logo are registered trademarks of Sony Corporation.
Precautions
- The supplied unmatch plug adaptor is only for the headphone cable; the balanced connection headphone cable cannot be used.
- To disconnect the headphone cable, pull it out by pulling the plug, not the cord. Otherwise, the cord may break.
- When connecting the headphone cable, make sure to fully insert the plug. If the plug is not fully inserted, the sound may not be output.
- When closing the hard case, be careful that your hands or cables are not caught in it.
- Press the catch of the hard case firmly until it clicks.
- Do not place a heavy object or sit on the hard case.
- Be sure to store the headphones with the jack facing upwards.
- Store the headphones by positioning both earpads against each other.
- You can store the headphones while attaching a cable to them.
- Natural leather is used for the headband and earpads. Unlike artificial leather, natural leather may have scars, creases, or lines resmbling the veins of a leaf from plants on its surface. Also, the texture and color shade may differ for each product.
- As leather is a soft material, it may be pockmarked when the headphones are stored wrapped around cables.
- To clean the headband and earpads, occasionally wipe them with a dry soft cloth. If it is still dirty, wipe and tap softly with a soft cloth moistened with hot water until it is cleaned. Do not use any detergent solution or maintenance agent for leather, otherwise, the leather may be damaged by discoloration, deformation, and degradation.
- When rain or sweat is attached, wipe the headphones with a soft dry cloth. If you leave it alone without any treatment, color deterioration or color migration may occur.
- Because the headphones are of a high-density enclosure, forcing them against your ears may result in eardrum damage. Avoid using headphones where they are liable to be struck by people or other objects, such as a ball, etc.
Pressing the headphones against your ears may produce a diaphragm click sound.
This is not a malfunction.
Only the supplied headphone cables and headphone cables for MDR-Z1R (sold separately) can be used with these headphones.
The validity of the CE marking is restricted to only those countries where it is legally enforced, mainly in the countries EEA (European Economic Area) and Switzerland.
Optional replacement earpads can be ordered from your nearest authorized Sony retailer or www.sony.com.
4-593-590-16(1)
©2016 Sony Corporation Printed in Japan
