Dewalt 20V Max* Pole Saw DCPS620 Instruction Manual

Instruction Manual
DCPS620
20V Max* Pole Saw

Definitions: Safety Alert Symbols and Words
This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk of personal injury or property damage.
DANGER: Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation that, if not avoided, may result in minor or moderate injury.
(Used without a word) Indicates a safety-related message.
NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in property damage.

COMPONENTS

1 Handle assembly
2 Center extension pole
3 Saw head assembly
4 Trigger switch
5 Lock button
6 Battery
7 Foam gripper
8 Threaded pole
9 Threaded sleeve		 10 Bar clamp
11 Sprocket cover
12 Hex head screws
13 Guide bar
14 Saw chain
15 Scabbard
16 Hex wrench
17 Oil cap
18 Branch removal hook

WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire, and/or serious injury.
WARNING: To reduce the risk of injury, read the instruction manual.
if you have any questions or comments about this or any DeWALT tool, call us toll-free at 1-800-4-DeWALT (1-800-433-9258).

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce risk of injury:
• Before any use, be sure everyone using this unit reads and understands all safety instructions and other information contained in this manual.
• Save these instructions and review them frequently.
WARNING: When using electric gardening appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury, including the following.

  1. Avoid Dangerous Environment – Don’t use appliances in damp or wet locations.
  2. Don’t Use In Rain.
  3. Keep Children Away – All visitors should be kept at a distance from the work area.
  4. Dress Properly – Do not wear loose clothing or jewelry.
    They can be caught in moving parts. Use of rubber gloves and substantial footwear is recommended when working outdoors. Wear protective hair covering to contain long hair.
  5. Use Safety Glasses – Always use a face or dust mask if the operation is dusty.
  6. Use Right Appliance – Do not use an appliance for any job except that for which it is intended.
  7. Don’t grasp the exposed cutting blades or cutting edges when picking up or holding the appliance.
  8. Don’t Force Appliance – It will do the job better and with less likelihood of a risk of injury at the rate for which it was designed.
  9. Don’t Overreach – Keep proper footing and balance at all times.
  10. Stay alert – Watch what you are doing. Use common sense. Do not operate appliances when you are tired.
  11. Disconnect Appliance – Remove the battery when not in use, before servicing, when changing accessories such as blades, and the like.
  12. Store Idle Appliances Indoors – When not in use, appliances should be stored indoors in dry, and high or locked-up places – out of reach of children.
  13. Maintain Appliance With Care – Keep the cutting edge sharp and clean for best performance and to reduce the risk of injury. Follow instructions for lubricating and
    changing accessories. Inspect appliance power source periodically, and if damaged, have it repaired by an authorized service facility. Keep handles dry, clean, and
    free from oil and grease.
  14. Check Damaged Parts – Before further use of the appliance, a guard or other part that is damaged should be carefully checked to determine that it will operate properly
    and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other condition that may affect its
    operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless indicated elsewhere in this manual.

SAVE THESE INSTRUCTIONS
WARNING – Do not operate near electrical power lines. The unit has not been designed to provide protection from electric shock in the event of contact with overhead electric lines, Consult local regulations for safe distances from overhead electric power lines and ensure that the operating position is safe and secure before operating the saw chain pole pruner.

  • Keep all parts of the body away from the saw chain.
    Do not remove cut material or hold material to be cut when blades are moving. Make sure the switch is off when clearing jammed material. Blades coast
    after turn off. A moment of inattention while operating the pole saw may result in serious personal injury.
  • Carry the pole saw by the handle with the saw chain stopped. When transporting or storing the pole saw always fit the saw chain device cover. Proper handling of
    the pole saw will reduce possible personal injury from the saw chain.
  • Hold the power tool by insulated gripping surfaces only, because the cutter blade may contact hidden wiring. A saw chain contacting a “live” wire may make
    exposed metal parts of the tool “live” and could give the operator an electric shock.
  • Do not use the pole saw in bad weather conditions, especially when there is a risk of lightning. This decreases the risk of being struck by lightning.
  • Always use two hands when operating the pole saw.
    Hold the pole saw with both hands to avoid loss of control.
  • Always use head protection when operating the pole saw overhead. Falling debris can result in serious personal injury.

SPECIFIC SAFETY RULES

WARNING: Some dust contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Some examples of these chemicals are:

  • compounds in fertilizers,
  • compounds in insecticides, herbicides, and pesticides,
  • arsenic and chromium from chemically treated lumber.
    To reduce your exposure to these chemicals, wear approved safety equipment such as dust masks that are specially designed to filter out microscopic particles.

Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote the absorption of harmful chemicals.
WARNING: Use of this tool can generate and/ or disburse dust, which may cause serious and permanent respiratory or another injury.
Always use NIOSH/OSHA-approved respiratory protection appropriate for dust exposure. Direct particles away from face and body.
CAUTION: Wear appropriate personal hearing protection during use. Under some conditions and duration of use, noise from this product may contribute to hearing loss.

Before Operating Pole Saw

  • For safe operation, read and understand all instructions before using the pole saw. Follow all safety instructions. Failure to follow all safety instructions listed below can result in serious personal injury.
  • Watch what you are doing. Use common sense. Do not operate a pole saw when you are tired.
  • Use pole saw for cutting tree branches only. Do not use a pole saw for purposes not intended. Do not use it for cutting other items.
  • Only well-instructed adults should operate the pole saws.
    Never allow children to operate.
  • Do not allow children or untrained individuals to use this unit.
  • Wear the following safety gear when operating pole saw:
    – heavy-duty gloves
    – steel-toed safety footwear with non-skid soles
    – safety glasses, goggles, or face screens that are marked to comply with ANSI Z87
    – safety hard hat that is marked to comply with ANSI Z89.1
    – ear mufflers or earplugs
    -face or dust mask (if working in dusty areas)
  • Wear heavy long pants and boots. Do not wear loose-fitting clothing, short pants, jewelry of any kind, or go barefoot.
  • Secure long hair so it is above shoulder level to prevent entanglement in any moving parts.
  • Before cutting, always provide the following:
    – clear work area
    – secure footing
    – planned retreat path from falling limbs
  • Inspect the tree before trimming. Make allowance for branches to fall freely to the ground.
  • Do not use your pole saw to fell saplings.

While Operating Pole Saw
DANGER: To reduce the risk of electric shock do not use it on wet surfaces. Do not expose to rain.
Store indoors.
DANGER: Avoid Unintentional Starting – with battery installed, don’t carry appliance with a finger on the switch. Be sure the switch is off when installing the battery.

  • Stay alert. Use common sense while operating the unit.
  • Keep work area clean. Cluttered areas invite injuries.
  • Always remove the battery from the pole saw when finished cutting or when left unattended.
  • Keep children, animals, and bystanders at least 50′ (15 m) away from the pole saw. Only pole saw users should be in the work area.
  • Do not use the pole saw to cut down trees.
  • Do not grasp the exposed saw chain when picking up or holding the pole saw.
  • Grip pole saw securely – one hand on the pole, the other on the handle.
  • Keep your finger off the trigger until ready to make the cut.
  • Before starting the pole saw, make sure the chain is not touching anything.
  • Keep all parts of the body away from the chain when the pole saw is running.
  • Do not force the pole saw while cutting. Apply light pressure. It will do the job better and safer at the rate for which it was intended.
  • Carry pole saw from one place to another:
    – with the battery removed,
    – fingers off/away from the trigger,
    – by holding the pole at the balance point, and
    -with a guide bar and chain to the rear and with a scabbard attached.
  • Do not cut small brushes and saplings with the pole saw. The slender matter may catch in the chain and be whipped toward you. This could also pull you off balance.
  • Do not operate in poor lighting.
  • Keep firm footing and balance. Do not overreach. Overreaching can result in loss of balance or exposure to hot surfaces.
  • Keep all parts of your body away from any moving part.
  • Do not, under any circumstance, use any attachment or accessory on this product, which was not provided with the product, or identified as appropriate for use with this product in this instruction manual.
  • Inspect pole saw before each use and after dropping or other impacts. Ensure there are no significant defects or damage.

Do Not Operate Pole Saw:

  • while under the influence of alcohol, medication, or drugs.
  • in rain or in damp or wet areas.
  • where highly flammable liquids or gases are present.
  • if pole saw is damaged, adjusted incorrectly, or not fully and securely assembled.
  • if the trigger does not turn the pole saw on and off. The chain must stop moving when you release the trigger. Has the faulty switch been replaced by the authorized service center? See Accessories under Maintenance.
  • while in a hurry.
  • while in a tree or on a ladder.
  • while on aerial booms, buckets, or platforms.
  • during high wind or storming weather.

GENERAL SAFETY RULES

DANGER: Shock Hazard. Serious injury or death from electrocution if power lines are contacted. Never use near any electrical source, wires, or power lines.
WARNING: For safe operation read and understand the owner’s manual. Wear a face shield (and/or safety glasses) and a hard hat to protect against falling debris. Always have a clear work area, retreat path, and be aware of limb/branch location to avoid falling limbs and debris. Keep bystanders 50 ft (15 m) away when operating the saw. To reduce the risk of electric shock do not use it on wet surfaces. Do not expose to rain. Store indoors.

  • To protect yourself from falling branches do not stand directly under the branch or limb being cut. This unit should not be held at an angle over 60° from ground level.
  • Keep the handles dry, clean, and free of oil.
  • Before you start the unit, make sure the chain is not contacting any object.
  • Make sure the cutting chain has stopped before setting the unit down.

Service

  • Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury. Refer to the Maintenance section of this manual.
  • When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury.

Guard Against Kickback

WARNING: KICKBACK may occur when the nose or tip of the guide bar touches an object, or when the wood closes in and pinches the saw chain in the cut.
Tip contact in some cases may cause a lightning-fast reverse reaction, kicking the guide bar up and back towards the operator. Pinching the saw chain along the top of the guide bar may push the guide bar rapidly back towards the operator. Either of these reactions may cause you to lose control of the saw which could result in serious injury to the user.
The following precautions should be followed to minimize kickback:

  • Grip pole saw firmly. Hold the saw firmly with both hands when the unit is running. Use a firm grip with thumbs and fingers encircling the saw handle and pole.
  • Do not overreach.
  • Keep proper footing and balance at all times.
  • Don’t let the noise of the guide bar contact a log, branch, ground, or other obstruction.
  • Do not extend the pole saw handle above shoulder height.
  • Use devices such as reduced kickback chain, chain braking system, and special guide bars that reduce the risks associated with kickback.
  • Only use replacement bars and chains specified by the manufacturer or the equivalent.
  • Never let the moving chain contact any object at the tip of the guide bar.
  • Keep the working area free from obstructions such as other trees, branches, rocks, fences, stumps, etc. Eliminate or avoid any obstruction that your saw chain could hit
    while you are cutting through a particular log or branch.
  • Keep your saw chain sharp and properly tensioned. A loose or dull chain can increase the chance of kickback. Check tension at regular intervals with the motor stopped and battery removed.
  • Begin and continue cutting only with the chain moving at full speed. If the chain is moving at a slower speed, there is a greater chance for a kickback to occur.
  • Cut one branch at a time.
  • Use extreme caution when re-entering a previous cut.
    Engage spiked bumpers into the wood and allow the chain to reach full speed before proceeding with the cut.
  • Do not attempt plunge cuts or bore cuts.
  • Watch for shifting branches or other forces that could close a cut and pinch or fall into the chain.

Kickback Safety Features

WARNING: The following features are included on your pole saw to help reduce the hazard of kickback; however such features will not totally eliminate this dangerous reaction. As a pole saw users do not rely only on safety devices. You must follow all safety precautions, instructions, and maintenance in this manual to help avoid kickback and other forces which can result in serious injury.

  • Reduced-Kickback Guide Bar, designed with a small radius tip which reduces the size of the kickback danger zone on bar tip. A reduced- kickback guide bar is one that has been demonstrated to significantly reduce the number and seriousness of kickbacks when tested in accordance with safety requirements for electric chain saws.
  • Reduced Kickback Chain, designed with a contoured depth gauge and guard link which deflect kickback force and allow the wood to gradually ride into the cutter. A reduced-kickback chain is a chain that has met the kickback performance requirements of ANSI B175.1–2012. when tested on the representative sample of chain saws.

Pole Saw Names and Terms

  • Drive Sprocket or Sprocket – The toothed part that drives the saw chain.
  • Guide Bar – A solid railed structure that supports and guides the saw chain.
  • Guide Bar Scabbard – Enclosure fitted over guide bar to prevent tooth contact when the saw is not in use.
  • Kickback – The backward or upward motion, or both of the guide bar occurring when the saw chain near the nose of the top area of the guide bar contacts any object
    such as a log or branch, or when the wood closes in and pinches the saw chain in the cut.
  • Reduced Kickback Chain – A chain that complies with the kickback performance requirements of ANSI B175.1–2012. (when tested on a representative sample of chain saws.
  • Reduced Kickback Guide Bar – A guide bar that has been demonstrated to reduce kickback significantly.
  • Replacement Saw Chain – A chain that complies with kickback performance requirements of ANSI B175.1–2012.
    when tested with specific chain saws. It may not meet the ANSI performance requirements when used with other saws.
  • Saw Chain – A loop of the chain having cutting teeth, that cut the wood, and that is driven by the motor and is supported by the guide bar.
  • Spiked Bumper (Spike) – The pointed tooth or teeth for use when pruning to pivot the saw and maintain position while sawing.
  • switch – A device that when operated will complete or interrupt an electrical power circuit to the motor of the chain saw.
  • Switch Lockout – A movable stop that prevents the unintentional operation of the switch until manually actuated.
  • Trimming (Pruning) – Process of cutting limbs from a tree.
  • Undercut – An upward cut from the underside of a log or limb. This is done while in the normal cutting position and cutting with the top of the guide bar.

Storage

  1. Store indoors. The best storage place is one that is cool and dries away from direct sunlight, excess heat, or cold and out of the reach of children.
  2. Always reduce the tension off the chain again after finishing work. The chain contracts as it cools down.
    If tension is not reduced, it can damage the saw.

The label on your tool may include the following symbols. The symbols and their definitions are as follows:

V volts or AC alternating current
Hz hertz
Class II Construction (double insulated)
min minutes no no-load speed
or DC direct current n rated speed
 Class I Construction (grounded) earthing terminal
…/min per minute safety alert symbol
BPM beats per minute visible radiation
IPM impacts per minute wear respiratory protection
RPM  revolutions per minute wear eye protection
sfpm  surface feet per minute wear hearing protection
SPM strokes per minute read all documentation
A amperes ** **
W watts ** **

BATTERIES AND CHARGERS

The battery pack is not fully charged out of the carton.
Before using the battery pack and charger, read the safety instructions below and then follow the charging procedures outlined. When ordering replacement battery packs, be sure to include the catalog number and voltage.
Your tool uses a DeWALT charger. Be sure to read all safety instructions before using your charger. Consult the chart at the end of this manual for compatibility of chargers and battery packs.
READ ALL INSTRUCTIONS
Important Safety Instructions for All Battery Packs
WARNING: Read all safety warnings and all instructions for the battery pack, charger, and power tool. Failure to follow the warnings and instructions may result in electric shock, fire, and/ or serious injury.

  • Do not charge or use the battery pack in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Inserting or removing the battery pack from the charger may ignite the dust or fumes.
  • NEVER force the battery pack into the charger. DO NOT modify the battery pack in any way to fit into a non-compatible charger as the battery pack may
    rupture causing serious personal injury. Consult the chart at the end of this manual for compatibility of batteries and chargers.
  • Charge the battery packs only in designated DeWALT chargers.
  • DO NOT splash or immerse in water or other liquids.
  • Do not store or use the tool and battery pack in locations where the temperature may reach or exceed 104 °F (40 °C) (such as outside sheds or metal
    buildings in summer). For best life store battery packs in a cool, dry location.
    NOTE: Do not store the battery packs in a tool with the trigger switch locked on. Never tape the trigger switch in the ON position.
  • Do not expose the battery pack or tool/appliance to fire or excessive temperature. Exposure to fire or temperature above 265°F (130°C) may cause an explosion.
  • Do not incinerate the battery pack even if it is severely damaged or is completely worn out. The battery pack can explode in a fire. Toxic fumes and materials are created when lithium-ion battery packs are burned.
  • If battery contents come into contact with the skin, immediately wash the area with mild soap and water. If battery liquid gets into the eye, rinse water over the open
    eye for 15 minutes or until irritation ceases. If medical attention is needed, the battery electrolyte is composed of a mixture of liquid organic carbonates and lithium salts.
  • Contents of opened battery cells may cause respiratory irritation. Provide fresh air. If symptoms persist, seek medical attention.

WARNING: Burn hazard. Battery liquid may be flammable if exposed to spark or flame.
WARNING: Fire hazard. Never attempt to open the battery pack for any reason. If the battery pack case is cracked or damaged, do not insert it into the charger.
Do not crush, drop or damage the battery pack. Do not use a battery pack or charger that has received a sharp blow, been dropped, run over, or damaged in any way (e.g., pierced with a nail, hit with a hammer, stepped on). Damaged battery packs should be returned to the service center for recycling.
Transportation
WARNING: Fire hazard. Do not store or carry the battery pack so that metal objects can contact exposed battery terminals. For example, do not place the battery pack in aprons, pockets, tool boxes, product kit boxes, drawers, etc., with loose nails, screws, keys, etc. Transporting batteries can possibly cause fires if the battery terminals inadvertently come in contact with conductive materials such as keys, coins, hand tools, and the like. The US Department of Transportation Hazardous Material Regulations (HMR) actually prohibits transporting batteries in commerce or on airplanes in carry-on baggage UNLESS they are properly protected from short circuits. So when transporting individual battery packs, make sure that the battery terminals are protected and well insulated from materials that could contact them and cause a short circuit.
NOTE: Lithium-ion batteries should not be put in checked baggage. shipping the DeWALT FlEXVOlT™ Battery The DeWALT FLEXVOLT™ battery has two modes: Use and shipping.
Use Mode: When the FLEXVOLT™ battery stands alone or is in a DeWALT 20V Max* product, it will operate as a 20V Max* battery. When the FLEXVOLT™ battery is in a 60V Max* or a 120V Max* (two 60V Max* batteries) product, it will operate as a 60V Max* battery. shipping Mode: When the cap is attached to the FLEXVOLT™ battery, the battery is in Shipping Mode. Strings of cells are electrically disconnected within the pack resulting in three batteries with a lower Watt-hour (Wh) rating as compared to one battery with a higher Watt hour rating. This increased quantity of three batteries with the lower Watt hour rating can exempt the pack from certain shipping regulations that are imposed upon the higher Watt hour batteries. The battery label indicates two Watt-hour ratings (see
example). Depending on how the battery is shipped, the appropriate Watt-hour rating must be used to determine the applicable shipping requirements. If utilizing the shipping cap, the pack will be considered 3 batteries at the Watt-hour rating indicated for “Shipping”. If shipping without the cap or in a tool, the pack will be considered one battery at the Watt-hour rating indicated next to “Use”.
Example of Use and Shipping Label Marking
USE: 120 Wh Shipping: 3 x 40 Wh For example, the Shipping Wh rating might indicate 3 x 40 Wh, meaning 3 batteries of 40 Watt-hours each. The Use Wh rating might indicate 120 Wh (1 battery implied).
Fuel Gauge Battery Packs
Some DeWALT battery packs include a fuel gauge which consists of three green LED lights that indicate the level of charge remaining in the battery pack.
The fuel gauge is an indication of approximate levels of charge remaining in the battery pack according to the following indicators:

75–100% charged

51–74% charged

< 50% charged

The pack needs to be charged

To actuate the fuel gauge, press and hold the fuel gauge button. A combination of the three green LED lights will illuminate designating the level of charge left. When the level of charge in the battery is below the usable limit, the fuel gauge will not illuminate and the battery will need to be recharged.
NOTE: The fuel gauge is only an indication of the charge left on the battery pack. It does not indicate tool functionality and is subject to variation based on product components, temperature, and end-user application.
For more information regarding fuel gauge battery packs, please call 1-800-4-DeWALT (1-800-433-9258) or visit our website www.dewalt.com.


The RBRC® Seal
The RBRC® (Rechargeable Battery  Recycling Corporation) Seal on the nickel-cadmium, nickel-metal hydride, or lithium-ion batteries (or battery packs) indicates that the costs
to recycle these batteries (or battery packs) at the end of their useful life have already been paid by DeWALT. In some areas, it is illegal to place spent nickel-cadmium, nickel-metal hydride, or lithium-ion batteries in the trash or municipal solid waste stream and the Call 2 Recycle® program provides an environmentally conscious alternative. Call 2
Recycle, Inc., in cooperation with DeWALT and other battery users, has established the program in the United States and Canada to facilitate the collection of spent nickel-cadmium, nickel-metal hydride, or lithium-ion batteries. Help protect our environment and conserve natural resources by returning the spent nickel-cadmium, nickel-metal hydride, or lithium-ion batteries to an authorized DeWALT service center or to your local retailer for recycling. You may also contact your local recycling center for information on where to drop off the spent battery. RBRC® is a registered trademark of Call 2 Recycle, Inc.

Important Safety Instructions for All Battery Chargers

WARNING: Read all safety warnings and all instructions for the battery pack, charger, and power tool. Failure to follow the warnings and instructions may result in electric shock, fire, and/ or serious injury.

  • DO NOT attempt to charge the battery pack with any chargers other than the ones in this manual.
    The charger and battery pack are specifically designed to work together.
  • These chargers are not intended for any uses other than charging DeWALT rechargeable batteries. Any other uses may result in a risk of fire, electric shock, or electrocution.
  • Do not expose the charger to rain or snow.
  • Pull by the plug rather than the cord when disconnecting the charger. This will reduce the risk of damage to the electric plug and cord.
  • Make sure that the cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress.
  • Do not use an extension cord unless it is absolutely necessary. Use of improper extension cord could result in a risk of fire, electric shock, or electrocution.
  • When operating a charger outdoors, always provide a dry location and use an extension cord suitable for outdoor use. The use of a cord suitable for outdoor use reduces the risk of electric shock.
  • An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety. The smaller the gauge number of the wire, the greater the capacity of the cable, that is, 16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. When using more than one extension to make up the total length, be sure each individual extension contains at least the minimum wire size. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The lower the gauge number, the heavier the cord.
    Minimum gauge for Cord sets

    Volts

    The total length of Cord in Feet (meters)

    120 V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)
    240 V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

    Ampere Rating

    American Wire gauge

    More Than

    not More Than

    0 6 18 16 16 14
    6 10 18 16 14 12
    10 12 16 16 14 12
    12 16 14 12

    Not Recommended

  • Do not place any object on top of the charger or place the charger on a soft surface that might block the ventilation slots and result in excessive internal heat. Place the charger in a position away from any heat source. The charger is ventilated through slots in the top and the bottom of the housing.
    • Do not operate the charger with a damaged cord or plug.
  • Do not operate the charger if it has received a sharp blow, been dropped, or otherwise damaged in any way. Take it to an authorized service center.
    • Do not disassemble the charger; take it to an authorized service center when service or repair is required. Incorrect reassembly may result in a risk of electric shock, electrocution, or fire.
    • Disconnect the charger from the outlet before attempting any cleaning. This will reduce the risk of electric shock. Removing the battery pack will not reduce
    this risk.
    • NEVER attempt to connect 2 chargers together.
    • The charger is designed to operate on standard 120V household electrical power. Do not attempt to use it on any other voltage. This does not apply to the
    vehicular charger.
    WARNING: Shock hazard. Do not allow any liquid to get inside the charger. Electric shock may result.
    WARNING: Burn hazard. Do not submerge the battery pack in any liquid or allow any liquid to enter the battery pack. Never attempt to open the battery pack for any reason. If the plastic housing of the battery pack breaks or cracks, return it to a service center for recycling.
    CAUTION: Burn hazard. To reduce the risk of injury, charge only DeWALT rechargeable battery packs.
    Other types of batteries may overheat and burst to result in personal injury and property damage.
    NOTICE: Under certain conditions, with the charger plugged into the power supply, the charger can be shorted by foreign material. Foreign materials of a conductive nature, such as, but not limited to, grinding dust, metal chips, steel wool, aluminum foil, or any buildup of metallic particles should be kept away from the charger cavities. Always unplug the charger from the power supply when there is no battery pack in the cavity. Unplug the charger before attempting to clean.

    • Charging a Battery

  1. Plug the charger into an appropriate outlet before inserting the battery pack.
  2. Insert the battery pack  6  into the charger, making sure the battery pack is fully seated in the charger. The red (charging) light will blink continuously indicating that
    the charging process has started.
  3. The completion of the charge will be indicated by the red light remaining ON continuously. The battery pack is fully charged and may be used at this time or left in the charger. To remove the battery pack from the charger, push the battery release button  23  on the battery pack and then slide the battery pack out of the charger.

NOTE: To ensure maximum performance and life of lithium-ion battery packs, charge the battery pack fully before first use.

 

 

 

If you have questions or comments, contact us.
1-800-4-DeWALT