JVC TH-E851B Soundbar with Wireless Subwoofer Instruction Manual

JVC TH-E851B Soundbar with Wireless SubwooferIMPORTANT SAFETY INSTRUCTIONS

The lightning flash with the arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude as to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to aler t the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Safety

Read these instructions – All the safety and operating instructions should be read before this product is operated.
Keep these instructions – The safety and operating instructions should be retained for future reference.
Heed all warnings – All warnings on the appliance and in the operating instructions should be adhered to.
Follow all instructions – All operating and usage instructions should be followed.
Do not use this apparatus near water – The appliance should not be used near water or moisture – for example, in a wet basement or near a swimming pool and the like.
Clean only with a dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heaters, stoves, or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding plug. A polarized plug has two blades with one wider than the other. A grounding plug has two blades and a third grounding prong. The wide blade orthe third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket or table specified by the manufacturer, or sold with the apparatus. When a cart or rack is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
Unplug the apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the unit has been exposed to rain or moisture, does not operate normally, or has been dropped.
This equipment is a Class II or double insulated electrical appliance. It has been designed in such a way that it does not require a safety connection to electrical earth.
The apparatus shall not be exposed to dripping or splashing. No objects filled with liquids, such as vases, shall be placed on the apparatus.
Minimum distance around the apparatus for sufficient ventilation is 5cm.
The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers,table-cloths, curtains, etc…
No naked flame sources, such as lighted candles, should be placed on the apparatus.
Batteries should be recycled or disposed of as per state and local guidelines.
The use of apparatus in moderate climates.

Caution

Use of controls or adjustments or performance of procedures other than those described herein, may result in hazardous radiation exposure or other unsafe operation.
To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The apparatus must not be exposed to dripping or splashing and objects filled with liquids, such as vases, must not be placed on apparatus.
The mains plug/appliance coupler is used as the disconnect device, the disconnect device must remain readily operable.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

Warning

The battery (batteries or battery pack) shall not be exposed to excessive heat such as sunshine, fire or the like.
Before operating this system, check the voltage of this system to see if it is identical to the voltage of your local power supply.
Do not place this unit close to strong magnetic fields.
Do not place this unit on the amplifier or receiver.
If any solid object or liquid falls into the system, unplug the system and have it checked by qualified personnel before operating it any further.
Do not attempt to clean the unit with chemical solvents as this may damage the finish. Use a clean, dry or slightly damp cloth.
When removing the power plug from the wall outlet, always pull directly on the plug, never yank on the cord.
Changes or modifications to this unit not expressly approved by the party responsible for compliance will void the user’s authority to operate the equipment.
The rating label is pasted on the bottom or back of the equipment.

Battery usage CAUTION

To prevent battery leakage which may result in bodily injury, property damage, or damage to the apparatus:
Install all batteries correctly, and as marked on the apparatus.
Do not mix old and new batteries.
Do not mix alkaline, standard (Carbon-Zinc) or rechargeable (Ni-Cd, Ni- MH, etc.) batteries.
Remove batteries when the unit is not used for a long time.

WHAT’S IN THE BOX

NOTE: Images, illustrations and drawings shown on this User Manual are for reference only, actual product may vary in appearance. Power cord quantity and plug type vary by regions.

IDENTIFYING THE PARTS

SOUNDBAR

Remote Control
Sensor Receive signal from the remote control.
Display Window
Show the current status.
Wall bracket screws
(ON/OFF) button
Switch the Soundbar between ON and Standby mode.
(SOURCE) button
Select the play function.
+/- (VOLUME) buttons
Increase/decrease the volume level.
AC~ Socket
Use to connect to power cable.
COAXIAL Socket
Use to connect to the COAXIAL OUT socket on an external device.
OPTICAL Socket
Use to connect to the OPTICAL OUT socket on an external device.
USB Socket
Insert the USB device to play music.
AUX Socket
Connect to an external audio device.
HDMI OUT (TV eARC/ARC) Socket
The port for connecting a TV. The port supports the eARC/ARC HDMI feature, which allows the soundbar to play audio that originates on the connected TV.
HDMI IN (1/2) Sockets
Two HDMI ports for connecting HDMI source devices, such as a DVD player, Blu-ray Disc™ player, or gaming console. Note that only one HDMI input is usable at a time.

WIRELESS SUBWOOFER

AC~ Socket
Connect to power supply.
PAIR button
Press activate the pairing function between the Soundbar and the subwoofer.
PAIR Indicator
Light stops blinking once the subwoofer is paired with the soundbar.

REMOTE CONTROL

button
Switch the Soundbar between ON and STANDBY mode.
SOURCE buttons
Press to select the source.
Press and hold to activate the pairing function in Bluetooth mode or disconnect the existing paired Bluetooth device.
buttons
BASS +/- buttons
Adjust bass level.
TREBLE +/- buttons
Adjust treble level.
(MUTE) button Mute or resume the sound. +/- (VOLUME) buttons Increase/decrease the volume level.
VERTICAL/SURROUND button Adjust the surround ON/OFF.
EQ buttons
Select Equalizer (EQ) Effect.
DIMMER button
Adjust display brightness.

Prepare the Remote Control

The provided remote control allows the Soundbar to be operated from a distance.

Even if the remote control is operated within the effective range 6m (19,7 feet), remote control operation may be impossible if there are any obstacles between the Soundbar and the remote control.
If the remote control is operated near other products which generate infrared rays, or if other remote control devices using infrared rays are used near the Soundbar, it may operate incorrectly. Conversely, the other products may operate incorrectly.

Replace the Remote Control Battery

Press and slide the back cover to open the battery compartment of the remote control.
Insert two AAA size batteries (included). Make sure the and ends of the batteries match the and ends indicated in the battery compartment.
Close the battery compartment cover.
Precautions Concerning Batteries
Be sure to insert the batteries with correct positive and negative polarities.
Use batteries of the same type. Never use different types of batteries together.
Either rechargeable or non-rechargeable batteries can be used. Refer to the precautions on their labels.
Be aware of your fingernails when removing the battery cover and the battery.
Do not drop the remote control.
Do not allow anything to impact the remote control.
Do not spill water or any liquid on the remote control.
Do not place the remote control on a wet object.
Do not place the remote control under direct sunlight or near sources of excessive heat.
Remove the battery from the remote control when not in use for a long period of time, as corrosion or battery leakage may occur and result in physical injury, and/or property damage, and/or fire.
Do not use any batteries other than those specified.
Do not mix new batteries with old ones.
Never recharge a battery unless it is confirmed to be a rechargeable type.

PLACEMENT AND MOUNTING

Placement

Option A
If your TV is placed on a table, you can place the Soundbar on the table directly in front of the TV stand, centered with the TV screen.
Option B
If your TV is attached to a wall, you can mount the Soundbar on the wall directly below the TV screen.

Wall Mounting (if using Option B)

Installation must be carried out by qualified personnel only. Incorrect assembly can result in severe personal injury and property damage (if you intend to install this product yourself, you must check for installations such as electrical wiring and plumbing that may be buried inside the wall). It is the installer’s responsibility to verify that the wall will safely support the total load of the Soundbar and wall brackets.
Additional tools (not included) are required for the installation.
Do not overtighten screws.
Keep this instruction manual for future reference.
Use an electronic stud finder to check the wall type before drilling and mounting.
WARNING
To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions.
Suggested wall mounting height: ≤ 1,5 meters.

Drill 4 parallel holes (Ø 5,5-6 mm each according to wall type) in the wall. The distance between the holes should be 870 mm.
Firmly fix 1 dowel into each hole in the wall if necessary. Tighten the wall mount brackets on the wall with screws and a screwdriver (not included). Make sure that they are securely installed.
Remove the screws at the back of the Soundbar. Install the wall mounting screws into the back of the Soundbar.
Lift the Soundbar onto the wall mount brackets and slot into place.

GENERAL OPERATION

CONNECT POWER

Risk of product damage! Ensure that the power supply voltage corresponds to the voltage printed on the back or the underside of the Soundbar.
Before connecting the AC power cord, ensure you have completed all other connections.

Soundbar
Connect the mains cable to the AC~ socket of the Soundbar and then into a mains socket.
Subwoofer
Connect the mains cable to the AC~ socket of the Subwoofer and then into a mains socket.
Note: If there is no power, ensure the power cord and plug are fully inserted and the power is turned on.

PAIR UP WITH THE SUBWOOFER

Automatic pairing
The subwoofer and soundbar will automatically pair when both units are plugged into the mains sockets and turned on. No cable is needed for connecting the two units.
Determine the status based on the wireless Subwoofer indicator:

Fast blink > Subwoofer in pairing mode
Constant on > Connected / Pairing successful
Slow blink > Connection / Pairing Failed
Fast blink > Subwoofer in pairing mode
Constant on > Connected / Pairing successful
Slow blink > Connection / Pairing Failed

Manual pairing

Ensure that all the cables are well connected and the Soundbar is in Standby mode.
Press and hold the PAIR button on the rear of the subwoofer for a few seconds. The subwoofer will enter the pairing mode and the Pair Indicator will blink quickly.
Press the button on the Soundbar or on the remote control to switch the Soundbar on.
After the wireless connection succeeded, the Pair Indicator will light up.
If the Pair indicator blinks, the wireless connection has failed. Unplug the cable of the subwoofer and then reconnect the main cable after 4 minutes. Repeat step 1 ~ 4.
NOTE:
If the wireless connection fails again, check if there is conflict or strong interference (for example, interference from an electronic device) around your location. Remove these conflicts or strong interferences and repeat the above procedures.
The subwoofer should be within 6 m (19,7 feet) of the soundbar in an open area.
If the Soundbar is not connected with the subwoofer and it is in On mode, the POWER Indicator will flash. Follow step 1 ~ 4 above to pair the subwoofer to the Soundbar.

STANDBY/ON

When you first connect the Soundbar to the mains socket, the Soundbar will be in Standby mode.

Press the button on the Soundbar or on the remote control to switch the Soundbar ON.
Press the button again to switch the Soundbar back to STANDBY mode.
Disconnect the mains plug from the mains socket if you want to switch the Soundbar OFF completely.

Automatic Power Off Function
The Soundbar automatically turns to Standby mode after about 15 minutes if the TV or the external unit is disconnected, switched off or the volume is too close to mute.

To switch the Soundbar off completely, remove the mains plug from the mains socket.
Please turn the Soundbar off completely to save energy when not in use.

SELECT MODES
Press the (SOURCE) button on the Soundbar or the AUX, , OPT/COA, HDMI 1/2, HDMI eARC and USB buttons on the remote control to select the desired mode. The selected mode will show on the display.
ADJUST THE BASS/TREBLE LEVEL
Press the BASS +/- buttons on the remote control to adjust bass level. Press the TREBLE +/- buttons on the remote control to adjust treble level.
TURN THE SURROUND SOUND ON/OFF
Press the VERTICAL/SURROUND button on the remote control to turn on the surround sound. Press this button again to turn off the surround sound.
SELECT EQUALIZER (EQ) EFFECT
Press the VOICE / SPORT / MOVIE / MUSIC buttons on the remote control to select your desired preset equalizer effects.
ADJUST THE VOLUME
Press the +/- (VOLUME) buttons on the Soundbar or on the remote control to adjust the volume. If you wish to turn the sound off, press the (MUTE) button on the remote control. Press the (MUTE) button again or press the +/- (VOLUME) buttons on the Soundbar or on the remote control to resume normal listening.
ADJUST THE BRIGHTNESS
Press the DIMMER button on the remote control to select brightness level.

CONNECTIONS

HDMI CONNECTION

Some 4K HDR TVs require the HDMI input or picture settings to be set for HDR content reception. For further setup details on HDR display, please refer to the instruction manual of your TV.
eARC / ARC (Enhance Audio Return Channel)
The eARC / ARC (Enhance Audio Return Channel) function allows you to send audio from your ARCcompliant TV to your soundbar through a single HDMI connection. To enjoy the ARC function, please ensure your TV is both HDMI-CEC and ARC compliant and set up accordingly. When correctly set up, you can use your TV remote control to adjust the volume output (VOLUME +/- and MUTE) of the soundbar.
Connect the HDMI cable (included) from unit’s HDMI OUT (TV eARC/ARC) socket to the HDMI (ARC) socket on your ARC-compliant TV. Then press the remote control to select ARC.NOTE:
Your TV must support the HDMI-CEC and ARC function. HDMI-CEC and ARC must be set to On. The setting method of HDMI-CEC and ARC may differ depending on the TV. For details about ARC function, please refer to the owner’s manual. ARC only works with devices that are HDMI ARC capable as well as with an HDMI 1.4 cable (and higher).

Standard HDMI

If your TV is not HDMI ARC-compliant, connect your soundbar to the TV through a standard HDMI connection.Use an HDMI cable to connect the soundbar’s HDMI OUT (TV eARC/ARC) socket to the TV’s HDMI IN socket.
Use an HDMI cable to connect the soundbar’s HDMI IN (1 or 2) socket to your external devices (e.g. games consoles, DVD players and Blu-ray).

USE THE OPTICAL SOCKET

Remove the protective cap of the OPTICAL socket, then connect an OPTICAL cable (not included) to the TV’s OPTICAL OUT socket and the OPTICAL socket on the Soundbar.

USE THE COAXIAL SOCKET

You also can use the COAXIAL cable (not included) to connect the TV’s COAXIAL OUT socket and COAXIAL socket on the Soundbar.

USE THE AUX SOCKET

Use a 3,5mm to 3,5mm audio cable (not included) to connect the TV’s or external audio device headphone socket to the AUX socket on the Soundbar.
Use a RCA to 3,5mm audio cable (included) to connect the TV’s audio output sockets to the AUX socket on the Soundbar.

AUX / OPTICAL / COAXIAL / HDMI OPERATION

Ensure that the Soundbar is connected to the TV or audio device.
Press the (SOURCE) button repeatedly on the Soundbar or press the AUX, OPT/COA, HDMI 1/2, HDMI eARC buttons on the remote control to select the desired mode.
the selected mode will show on the display.
Press the +/- (VOLUME) button to adjust the volume to your desired level.

NOTE:
The Soundbar may not be able to decode all digital audio formats from the input source. In this case, the Soundbar will mute. This is NOT a defect. Ensure that the audio setting of the input source (e.g. TV, game console, DVD player, etc.) is set to PCM or Dolby Digital (Refer to the user manual of the input source device for its audio setting details) with HDMI 1 / HDMI 2 / HDMI ARC / OPTICAL / COAXIAL input. When selecting a different audio format, the Soundbar will display the following as follows:

Audio (abbreviation) Display
LPCM 2ch, LPCM 5.1ch, LPCM 7.1ch PCM AUDIO
Dolby Digital, Dolby TrueHD, Dolby Digital Plus DOLBY AUDIO
Dolby Atmos – Dolby TrueHD, Dolby Atmos – Dolby Digital Plus DOLBY ATMOS

BLUETOOTH® OPERATION

Pairing the Soundbar with a Bluetooth® device to listen to music.

First time pairing

Press the (SOURCE) button repeatedly on the Soundbar or press the button on the remote control to select Bluetooth® mode. The display will show NO BT.
Activate your Bluetooth® device and select the search mode. “TH-E851B” will appear on your Bluetooth® device list.
Select “TH-E851B” enter “0000” for the password if necessary. The Soundbar will voice “Paired” and the display will show BT.

Pairing a new device

In Bluetooth® mode, press and hold the or button to clear all pairing. The Soundbar will enter pairing mode. The Soundbar will voice “Pairing“ and the display will show PAIR.
Follow step 2-3 in “First time pairing“ above to pair a new Bluetooth® device.

Listen to Music from Bluetooth® device
If your Bluetooth® device supports A2DP, play music via your device.
If your Bluetooth® device supports AVRCP, use the supplied remote control to control play.

To increase/decrease the volume, press +/- (VOLUME) button.
To pause/resume playback, press button.
To skip to a track, press button.
To disconnect the Bluetooth® function,you can:
Switch to another source on the Soundbar;
Disable the function from your Bluetooth® device.

NOTE:
The operational range between the Soundbar and the device is approximately 8 metres.
Before connecting a Bluetooth® device to the Soundbar, ensure you know the device’s capabilities. Compatibility with all Bluetooth® devices is not guaranteed.
Any obstacle between the device and the Soundbar can reduce operational range.
Keep this player away from other electronic devices that may cause interference.
The player will also be disconnected when your device is moved beyond the operational range.

USB OPERATION

By connecting a USB mass storage device (e.g. USB flash drive) to this unit, you can enjoy the device’s stored music through the Soundbar.

Press the (SOURCE) button on the Soundbar or press the USB button on the remote control to select USB mode.
Press button 2. Press button
To skip to a track, press / button.
NOTE:
The player supports the USB music file format of MP3 only.
The Soundbar can support USB devices with up to 32 GB of memory.
The Soundbar may not be compatible with all USB devices, this is not an indication of a problem with the unit.

DOLBY ATMOS®

Dolby Atmos® gives you immersive listening experience by delivering sound in three dimensional space, and all the richness, clarity, and power of Dolby sound. For more information, please visit dolby.com/technologies/dolby-atmos
For using Dolby Atmos®

Dolby Atmos® is available only in HDMI mode. For the details of the connection, please refer to “HDMI Connection”.
To use Dolby Atmos® in HDMI1, HDMI2 and HDMI ARC/eARC mode, your TV has to support Dolby Atmos®.
Make sure that “No Encoding“ is selected for bitstream in the audio output of the connected external device (e.g. Blu-ray DVD player, TV etc.).
NOTE:
The full Dolby Atmos experience is only available when the soundbar is connected to the source via a HDMI 2.0 cable.
The soundbar will still function when connected via other methods (such as a Digital Optical cable) but these are unable to support all of the Dolby features. Given this, our recommendation is to connect via HDMI, in order to ensure full Dolby support.

LICENCE NOTIFICATION

Bluetooth®

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Zhong Shan City Richsound Electronic Industrial Ltd. is under license. Other trademarks and trade names are those of their respective owners.
Dolby Atmos
Dolby, Dolby Atmos, and the double-D symbol are registered trademarks of Dolby Laboratories Licensing Corporation. Manufactured under license from Dolby Laboratories. Confidential unpublished works. Copyright © 2012-2021 Dolby Laboratories. All rights reserved.
HDMI
The Adopted Trademarks HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries.

TROUBLESHOOTING

To keep the warranty valid, never try to repair the system yourself. If you encounter problems when using this unit, check the following points before requesting service. SPECIFICATIONS

WE RESERVE THE RIGHT TO CHANGE TECHNICAL SPECIFICATIONS.
WARNING: DO NOT USE THIS PRODUCT NEAR WATER, IN WET AREAS TO AVOID FIRE OR INJURY OF ELECTRIC CURRENT. ALWAYS TURN OFF THE PRODUCT WHEN YOU DON’T USE IT OR BEFORE A REVISION. THERE AREN’T ANY PARTS IN THIS APPLIANCE WHICH ARE REPARABLE BY CONSUMER. ALWAYS APPEAL TO A QUALIFIED AUTHORIZED SERVICE. THE PRODUCT IS UNDER A DANGEROUS TENTION.
TO AVOID DANGER OF SUFFOCATION, KEEP THE PLASTIC BAG AWAY FROM BABIES AND CHILDREN. DO NOT USE THIS BAG IN CRIBS, BEDS, CARRIAGES OR PLAYPENS. THIS BAG IS NOT A TOY.

Disposal of old Electrical & Electronic Equipment

(Applicable in the European Union and other European countries with separate collection systems) This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.
Hereby, ETA a.s. declares that the radio equipment type TH-E851B is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.JVCAUDIO.cz/doc

Download

JVC TH-E851B Soundbar with Wireless Subwoofer Instruction Manual

Was this manual helpful?