Sony XS-160ES 6.5″ Mobile ES 2-Way Coaxial Speaker Instruction Manual

SONY XS-160ES 2-Way Speaker Instruction Manual

5-026-672-11(1)

 

Dimensions

A Reference Point
B Reference Plane
C Reference Axis

Notice for customers: the following information is only applicable to equipment sold in countries applying EU directives
This product has been manufactured by or on behalf of Sony Corporation.
EU Importer: Sony Europe B.V.
Inquiries to the EU Importer or related to product compliance in Europe should be sent to the manufacturer’s authorized representative, Sony Belgium, bijkantoor van Sony Europe B.V., Da Vincilaan 7-D1, 1930 Zaventem, Belgium.

Disposal of old electrical & electronic equipment (applicable in the European Union and other countries with separate collection systems)

This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the appropriate collection point for the recycling of electrical and electronic equipment. By ensuring that this product is disposed of correctly, you will help to prevent potential negative consequences for the environment and human health, which could be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.

Precautions

  • Do not continuously use the speaker system beyond the peak power handling capacity.
  • Keep recorded tapes, watches, and personal credit cards using magnetic coding away from the speaker system to protect them from damage caused by the magnets in the speakers.
  • Please note the following when installing the units; otherwise malfunction and/or deterioration in sound quality may result.
    • Do not touch the diaphragms and/or speaker cones by hand or with tools.
    • Do not put your fingers through the holes of the frame.
    • Do not drop foreign objects in the units.
  • Do not place this product close to medical devices.
    • This product (including accessories) has magnet(s) which may interfere with pacemakers, programmable shunt valves for hydrocephalus treatment, or other medical devices. Do not place this product close to persons who use such medical devices. Consult your doctor before using this product if you use any such medical device.

If you cannot find an appropriate mounting location, consult your car dealer or your nearest Sony dealer before mounting.

Specifications

Speaker

Coaxial 2 way:
Woofer 16.5 cm (6 1 /2 in) cone type
Tweeter 2.0 cm (13/16 in) dome type

Short-term maximum power*1

270 W*2

Rated power

60 W*2

CTA 2031 RMS Power

90 W

Rated impedance

4 Ω

Output sound pressure level

89±2 dB (1 W, 1 m)*2

Effective frequency range

45 – 40,000 Hz*2

Mass

Woofer: Approx. 990 g (2 lb 3 oz) per speaker

Supplied accessories

Parts for installation

Design and specifications are subject to change without notice.

*1 “Short-term maximum power” may also be referred to as “Peak Power”.
*2 Testing Condition: IEC 60268-5 (2003-05)

Mounting

Before mounting

A depth of at least 53.5 mm (2 1 /8 in) is required to mount the woofer. Measure the depth of the area where you are to mount the speaker, and ensure that the speaker is not obstructing any other components of the car. Keep the followings in mind when choosing a mounting location:

  • Make sure that nothing is obstructing around the mounting location of the door (front or rear) where you are to mount the speaker.
  • A hole for mounting may already be cut out of the inner panel of the door (front or rear). In this case, you need to modify the board only.
  • If you are to mount this speaker system in the door (front or rear), make sure that the speaker terminals, frame or magnet do not interfere with any inner parts, such as the window mechanism in the door (when you open or close the window), etc. Also make sure that the speaker grille does not touch any inner fittings, such as the window cranks, door handles, arm rests, door pockets, lamps or seats etc.
  • If you are to mount this speaker system in the rear tray, make sure that the speaker terminals, frame or magnet do not touch any inner parts of the car, such as the torsion bar springs (when you open or close the trunk lid), etc. Also make sure that the speaker grille does not touch any inner fittings, such as seat belts, head rests, center brake lights, inner covers of the rear wipers, curtains or air purifiers, etc.

Parts list

Mounting from the car interior

DOOR (FRONT/REAR)

  1. Mark the 4 bolt holes and make them 3.2 mm (1 /8 in) in diameter.
    Door panel
    Unit: mm (in)
  2. Standard connection
    Speaker cord (not supplied)

    Power amplifier, etc.
  3. Speaker cord (not supplied)

Connections

*1 Left speaker
*2 Right speaker

Standard connection

*1 Left speaker
*2 Right speaker