Beko WUE 8512 PAR Washing Machine User Manual

WUE 8512 PAR Washing Machine

Washing Machine
User’s Manual

WUE 8512 PAR EN/EL
Document Number=1911861417_EN / 27-08-20.(14:54)

This product was manufactured using the latest technology in environmentally friendly conditions.

1 General safety nstruct ons
This section includes security instructions which may help prevent the injuries and material damage risks. All kinds of warranties shall be invalid if these instructions are not observed.
1.1 L fe and property safety Never place the product on a carpet-covered floor. Electr cal parts w ll get overheated s nce a r cannot c rculate from under the dev ce. Th s w ll cause problems w th your product. Unplug the product f t s not n use. Always have the nstallat on and repa r ng procedures carr ed out by the Author sed Serv ce Agent. The manufacturer shall not be held l able for damages that may ar se from procedures carr ed out by unauthor sed persons. The water supply and dra n ng hoses must be securely fastened and rema n undamaged. Otherw se, water leak may occur. Wh le there s st ll water ns de the product, never open the load ng door or remove the f lter. Otherw se, r sk of flood ng and njury from hot water w ll occur. Do not force open the locked load ng door. Door can be opened a few m nutes after the wash ng cycle ends. In case of forc ng the load ng door to open, the door and the lock mechan sm may get damaged. Use detergents, softeners and supplements su table for automat c wash ng mach nes only. Follow the nstruct ons on the label of text les and the detergent package.
1.2 Ch ldren’s safety Th s product can be used by the ch ldren who are at the age of 8 and over and the people whose phys cal, sensory or mental sk lls are not fully developed or who do not have necessary requ red exper ence and knowledge as long as they are superv sed or tra ned about the safe use of the product and ts r sks. Ch ldren should not play w th the dev ce. Clean ng and ma ntenance works should not be performed by ch ldren unless they are superv sed by someone. Ch ldren of less than 3 years should be kept away unless cont nuously superv sed. Packag ng mater als may be dangerous for the ch ldren. Keep packag ng mater als n a safe place away from reach of the ch ldren.

Wash ng Mach ne / User’s Manual

3 / EN

Electr cal products are dangerous for the ch ldren. Keep the ch ldren away from the product when t s n use. Do not allow them to play w th the product. Use ch ld lock to prevent ch ldren from nterven ng w th the product.
Do not forget to close the load ng door when leav ng the room where the product s located.
Store all detergents and add t ves n a safe place away from the reach of the ch ldren by clos ng the cover of the detergent conta ner or seal ng the detergent package.
1.3 Electr cal safety If the product has a fa lure, t should not be operated unless t s repa red by the Author sed Serv ce Agent. R sk of electr c shock! Th s product s des gned to resume operat ng n the event of power ng on after a power nterrupt on. If you w sh to cancel the programme, see “Cancell ng the programme” sect on. Plug the product nto a grounded outlet protected by a 16 A fuse. Do not neglect to have the ground ng nstallat on made by a qual f ed electr c an. Our company shall not be l able for any damages that w ll ar se when the product s used w thout ground ng n accordance w th the local regulat ons. Do not wash the product by spray ng or pour ng water onto t! R sk of electr c shock! Never touch the power cable plug w th wet hands! Do not grab the power cord to unplug the mach ne, always unplug t by hold ng the socket w th one hand, and pull ng the plug w th the other hand. Product should be unplugged dur ng nstallat on, ma ntenance, clean ng and repa r procedures. If the power cable s damaged, t must be replaced by the manufacturer, after sales serv ce or a s m larly qual f ed person (preferably an electr c an) or someone des gnated by the mporter n order to avo d poss ble r sks.
1.4 Hot surface safety
While washing the laundry at high temperatures, the loading door glass will get hot. Considering this fact, during washing operation keep the children away from the loading door of the product to prevent them touching it.

4 / EN

Wash ng Mach ne / User’s Manual

2 Important instructions for environment
Compliance with the WEEE Directive and Disposing of the Waste Product:
This product complies with EU WEEE Directive (2012/19/EU). This product bears a classification symbol for waste electrical and electronic equipment (WEEE).
This symbol indicates that this product shall not be disposed with other household wastes at the end of its service life. Used device must be returned to offical collection point for recycling of electrical and electronic devices. To find these collection systems please contact to your local authorities or retailer where the product was puchased. Each household performs important role in recovering and recycling of old appliance. Appropriate disposal of used appliance helps prevent potential negative consequences for the environment and human health.
Compliance with RoHS Directive
The product you have purchased complies with EU RoHS Directive (2011/65/EU). It does not contain harmful and prohibited materials specified in the Directive.
Package nformat on
Packaging materials of the product are manufactured from recyclable materials in accordance with our National Environment Regulations. Do not dispose of the packaging materials together with the domestic or other wastes. Take them to the packaging material collection points designated by the local authorities.
3 Intended use
· This product has been designed for domestic use. It is not for commercial purposes or it should not be used out of its intended use.
· The product must only be used for washing and rinsing of laundry that are marked accordingly. · The manufacturer waives any responsibility arisen from incorrect usage or transportation. · The service life of your product is 10 years. During this period, original spare parts will be available
to operate the appliance properly.

Wash ng Mach ne / User’s Manual

5 / EN

4 Technical specifications
Supplier name or trademark
Model name
Height (cm) Width (cm) Depth (cm) Net weight (±4 kg.) Single Water inlet / Double Water inlet · Available Electrical input (V/Hz) Total current (A) Total power (W) Main model code

Beko WUE 8512 PAR 7000940008
84 60 55 66
· / –
230 V / 50Hz 10 2200 9220

C BEKO
A

MODEL IDENTIFIER (*)
A

The model nformat on as stored n the product database can be reached by enter ng follow ng webs te and search ng for your model dent f er (*) foundon energy label: https://eprel.ec.europa.eu/

6 / EN

Wash ng Mach ne / User’s Manual

4.1 Installation
· Apply to the nearest authorised service agent for the installation of your product. · Preparation of the location and electrical, tap water and waste water installations at the place of
installation is under customer’s responsibility. · Make sure that the water inlet and discharge hoses as well as the power cable are not folded,
pinched or crushed while pushing the product into its place after installation or cleaning procedures. · Make sure that the installation and electrical connections of the product are performed by authorised service. Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorised persons. · Prior to installation, visually check if the product has any defects on it. If so, do not have it installed. Damaged products cause risks for your safety.
4.1.1 Appropr ate nstallat on locat on · Place the product on a hard and level floor. Do not put it onto a carpet with high pile or other similar surfaces. · When the washing machine and dryer are placed on top of each other, their total weight when loaded amounts to 180 kilograms. Place the product on a solid and flat floor that has sufficient load carrying capacity! · Do not place the product on the power cable. · Do not install the product in the environments where the temperature falls below 0 ºC. · Leaving a gap at the sides of the machine is suggested to reduce vibration and noise · On a graduated floor, do not place the product next to the edge or on a platform. · Do not place heat sources such as Hobs, Irons, Ovens, etc. on the washing machine and do not use them on the product.
4.1.3 Remov ng the transportat on locks
1 Loosen all bolts with an appropriate wrench until they turn freely. 2 Remove the transport safety bolts by turning them slightly. 3 Insert the plastic covers in the bag containing the user manual to the openings on the rear
panel.

A
C

CAUTION: Remove the transportation safety bolts before operating the washing machine! Otherwise, the
product will be damaged.
Keep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved again in the future. Install the transport safety bolts in reverse order of the disassembly procedure. Never move the product without the transportation safety bolts properly fixed in place!

Wash ng Mach ne / User’s Manual

7 / EN

4.1.4 Connect ng water supply

C
A

The water supply pressure required to run the product is between 1 to 10 bars (0.1 1 MPa). It is necessary to have 10 80 liters of water flowing from the fully open tap in one minute to have your machine run smoothly. Attach a pressure reducing valve if water pressure is higher.
CAUTION: Models with a single water inlet should not be connected to the hot water tap. In such a case the
laundry will get damaged or the product will switch to protection mode and will not operate.
CAUTION: Do not use old or used water inlet hoses on the new product. It may cause stains on your laundry.

1 Tighten the nuts of the hose by hand. Never use a tool when tightening the nuts.
2 When hose connection is completed, check whether there is leak problems at the connection points by opening the taps fully. If any leaks occur, turn off the tap and remove the nut. Retighten the nut carefully after checking the seal. In order to prevent the water leaks and resultant damages, keep the taps closed when you do not use the product.
4.1.5 Connect ng the dra n hose to the dra n · Attach the end of the drain hose directly to waste water drain, lavatory or bathtub.

CAUTION: Your drain house will be flooded if the hose comes out of its housing during water discharge.
Moreover, there is risk of scalding due to high washing temperatures! In order to prevent such situations and make sure that the machine performs water intake and discharge processes without any problem, fix the drain hose securely.

100 cm 40 cm

· Connect the drain hose to a minimum height of 40 cm and a maximum height of 100 cm. · In case the drain hose is elevated after laying it on the floor level or close to the ground (less than 40 cm above the ground), water discharge becomes more difficult and the laundry may come out excessively wet. Therefore, follow the heights described in the figure.
· To prevent the waste water to go back into the machine again and to ensure easy drainage, do not immerse the end of the hose into the waste water or do not insert it into the drain for more than 15 cm. If it is too long, cut it short.
· The end of the hose should not be bent, it should not be stepped on and the hose must not be pinched between the drain and the machine.
· If the length of the hose is too short, use it by adding an original extension hose. Length of the hose may not be longer than 3.2 m. To avoid water leak failures, the connection between the extension hose and the drain hose of the product must be fitted well with an appropriate clamp as not to come off and leak.

8 / EN

Wash ng Mach ne / User’s Manual

4.1.6 Adjust ng the feet

CAUTION: In order to ensure that the product operates more silently and vibration-free, it must stand level
and balanced on its feet. Balance the machine by adjusting the feet. Otherwise, the product may move from its
place and cause crushing and vibration problems.

CAUTION: Do not use any tools to loosen the lock nuts. Otherwise, they will get damaged.

1 Loosen the lock nuts on the feet by hand. 2 Adjust the feet until the product stands in a stable and balanced way. 3. Tighten all lock nuts by hand again.

4.1.7 Electr cal connect on Connect the product to a grounded outlet protected by a 16 A fuse. The Manufacturer shall not be liable for any damages that will arise when the product is used without grounding in accordance with the local regulations. · Connection must comply with national regulations. · The wiring for the electrical outlet circuit must be sufficient to meet the appliance requirements. Use of a Groud Fault Circuit Interrupter (GFCI) is recommended. · Power cable plug must be within easy reach after installation. · If the current value of the fuse or breaker in the house is less than 16 Amps, have a qualified electrician install a 16 Amp fuse. · The voltage specified in the “Technical specifications” section must be equal to your mains voltage. · Do not make connections via extension cables or multi-plugs.

CAUTION: Damaged power cables must be replaced by the Authorised Service Agents.

4.1.8 In t al use

Before starting to use the product make sure that the preparations are made which are in line with the “Important Safety and Environment Instructions” and the instructions in the “Installation” section. To prepare the product for washing laundry, perform first operation in Drum Cleaning programme. If this program is not available in your machine, apply the method which is described in the section 4.4.2.

Use an anti-limescale suitable for the washing machines.
Some water might have remained in the product due to the quality control processes in the production. It is not harmful for the product.

Wash ng Mach ne / User’s Manual

9 / EN

4.2 Preparation

4.2.1 Sort ng the laundry * Sort laundry according to type of fabric, color, and degree of soiling and allowable water temperature. * Always obey the instructions given on the garment tags.

4.2.2 Prepar ng laundry for wash ng · Laundry items with metal attachments such as, underwired bras, belt buckles or metal buttons will damage the machine. Remove the metal pieces or wash the clothes by putting them in a laundry bag or pillow case. · Take out all substances in the pockets such as coins, pens and paper clips, and turn pockets inside out and brush. Such objects may damage the product or cause noise problem. · Put small size clothes such as infant’s socks and nylon stockings in a laundry bag or pillow case. · Place curtains in without compressing them. Remove curtain attachment items. · Fasten zippers, sew loose buttons and mend rips and tears. · Wash “machine washable” or “hand washable” labeled products only with an appropriate programme. · Do not wash colours and whites together. New, dark coloured cottons release a lot of dye. Wash them separately. · Tough stains must be treated properly before washing. If unsure, check with a dry cleaner. · Only use the dyes / color changers and descaling agents which are appropriate to machine wash. Always follow the instructions on the package. · Wash trousers and delicate laundry turned inside out. · Keep laundry items made of Angora wool in the freezer for a few hours before washing. This will reduce pilling. · Laundry that are subjected to materials such as flour, lime dust, milk powder, etc. intensely must be shaken off before placing into the machine. Such dusts and powders on the laundry may build up on the inner parts of the machine in time and can cause damage.

4.2.3 T ps for energy and water sav ng Following information will help you use the product in an ecological and energy/water-efficient manner. · Operate the product in the highest load capacity allowed for the programme you have selected, but do not overload. See, “Programme and consumption table”. · Observe the temperature instructions on the detergent packaging. · Wash slightly soiled laundry at low temperatures. · Use faster programmes for small quantities of lightly soiled laundry. · Do not use prewash and high temperatures for laundry that is not heavily soiled or stained. · If you plan to dry your laundry in a dryer, select the highest spin speed recommended during washing process. · Do not use more detergent than the recommended on the detergent packaging.

4.2.4 Load ng the laundry 1. Open the laundry cover. 2. Put the laundry items into the machine in a loose manner. 3. Push and close the loading cover until you hear the locking sound. Ensure that no items are caught in the door. The loading door is locked while a programme is running. The door can only be opened a while after the programme comes to an end.

4.2.5 Correct load capac ty The maximum load capacity depends on the type of laundry, the degree of soiling and the washing programme desired. Machine automatically adjusts the water amount according to the weight of the laundry put inside it.

WARNING: Follow the information in the “Programme and consumption table”. When overloaded, machine’s
washing performance will drop. Moreover, noise and vibration problems may occur.

10 / EN

Wash ng Mach ne / User’s Manual

4.2.6 Us ng detergent and softener

When using detergent, softener, starch, fabric dye, bleacher and decolorant, descaling agents; read the manufacturer’s instructions written on the package and follow the dosages specified. Use measuring cup if available.

2 31

The detergent drawer is composed of three compartments: (1) for prewash (2) for main wash (3) for softener ( ) in addition, there is a siphon piece in the softener compartment.

Detergent, softener and other cleaning agents · Add detergent and softener before starting the washing programme. · While the washing cycle is in progress, do not leave the detergent dispenser open! · When using a programme without prewash, do not put any detergent into the prewash
compartment (compartment nr. “1”). · In a programme with prewash, do not put liquid detergent into the prewash compartment
(compartment nr. “1”). · Do not select a programme with prewash if you are using a detergent bag or dispensing ball. Place
the detergent bag or the dispensing ball directly among the laundry in the machine. If you are using liquid detergent, do not forget to place the liquid detergent container into the main
wash compartment (compartment number “2”). Choosing the detergent type Detergent type to be used depends on the washing programme, fabric type and color. · Use different detergents for coloured and white laundry. · Wash your delicate clothes only with special detergents (liquid detergent, wool shampoo, etc.)
intended solely for delicate clothes and at suggested programmes. · When washing dark coloured clothes and quilts, it is recommended to use liquid detergent. · Wash woolens at suggested programme with special detergent made specifically for woolens · Please review the program descriptions part for suggested program for different textiles. · All recommendations about detergents are valid for selectable temperature range of programmes.

CAUTION: Use only detergents manufactured specifically for washing machines. CAUTION: Do not use soap powder.

Adjusting detergent amount The amount of washing detergent to be used depends on the amount of laundry, the degree of soiling and water hardness. · Do not use amounts exceeding the dosage quantities recommended on the detergent package
to avoid problems of excessive foam, poor rinsing, financial savings and finally, environmental protection. · Use lesser detergent for small amounts or lightly soiled clothes. Using softeners Pour the softener into the softener compartment of the detergent drawer. · Do not exceed the (>max<) level sign on the softener compartment. · If the softener has lost its fluidity, dilute it with water before putting it in the detergent drawer.

Wash ng Mach ne / User’s Manual

11 / EN

Using liquid detergents

If the product contains a liquid detergent cup:

Put the liquid detergent container into the compartment no “2”. If the liquid detergent lost its fluidity, dilute it with water before putting it into the detergent container.

If the product is equipped with a liquid detergent part:
· When you want to use liquid detergent, press on the point shown to rotate the apparatus. The part that falls off will function as a barrier for the liquid detergent.
· If required, clean the apparatus with water when it is in place or by removing it.
· If you will use powder detergent, the apparatus must be secured at top position.
If the product does not contain a liquid detergent cup: · Do not use liquid detergent for the prewash in a programme with prewash. · Liquid detergent stains your clothes when used with Delayed Start function. If you are going to
use the Delayed Start function, do not use liquid detergent. Using gel and tablet detergent · If the gel detergent thickness is fluidal and your machine does not contain a special liquid
detergent cup, put the gel detergent into the main wash detergent compartment during first water intake. If your machine contains a liquid detergent cup, fill the detergent into this cup before starting the programme. · If the gel detergent thickness is not fluidal or in the shape of capsule liquid tablet, put it directly into the drum before washing. · Put tablet detergents into the main wash compartment (compartment nr. “2”) or directly into the drum before washing. Using starch · Put the liquid soda, powder soda or the fabric dye into the softener compartment. Do not use softener and starch together in a washing cycle. Wipe the inside of the machine with a damp and clean cloth after using starch. Using limescale remover · When required, use limescale removers manufactured specifically for washing machines only. Using bleaches · Add the bleach at the beginning of the washing cycle by selecting a prewash program. Do not put detergent in the prewash compartment. As an alternative application, select a programme with extra rinse and add the bleaching agent while the machine is taking water from the detergent compartment during first rinsing step. · Do not use bleaching agent and detergent by mixing them. · Use just a little amount (approx. 50 ml) of bleaching agent and rinse the clothes very well as it causes skin irritation. Do not pour the bleach onto the laundry and do not use it with the colored items. · When using oxygen-based decolorant, select a program which washes the laundry at a low temperature. · Oxygen-based decolorant can be used with the detergent; however, if it is not at the same consistence, first put detergent in the compartment number “2” in the detergent dispenser and wait for the machine to flush the detergent when taking in water. While the machine continues taking in water, add decolorant in the same compartment.

12 / EN

Wash ng Mach ne / User’s Manual

4.2.7 T ps for eff c ent wash ng

Clothes

Light Colours and Whites

Colours

Black/Dark

Delicates/

Colours

Woolens/Silks

(Recommended toenmspoeilirnagtulereveral:n4g0e-9ba0soeCd)

(Recommended temperature range based oonC)soiling level: cold -40

(Recommended (Recommended temperature range temperature range bleavseel:dcoonlds-o4il0inogC) bleavseel:dcoonlds-o3i0linogC)

Soiling Level

It may be necessary to pre- Powder and liquid

treat the stains or perform detergents recommended

Heavily Soiled

prewash. Powder and liquid for colors can be used at Liquid detergents detergents recommended dosages recommended suitable for for whites can be used at for heavily soiled clothes. colors and dark

dosages recommended It is recommended to use colors can be

(difficult stains for heavily soiled clothes. powder detergents to used at dosages

such as grass, It is recommended to use clean clay and soil stains recommended

coffee, fruits powder detergents to

and the stains that are for heavily soiled

and blood.)

clean clay and soil stains sensitive to bleaches.

clothes.

and the stains that are Use detergents without

sensitive to bleaches.

bleach.

Prefer liquid detergents produced for delicate clothes. Woolen and silk clothes must be washed with special woolen detergents.

Normally
Soiled (For example, stains caused by body on collars and cuffs)

Powder and liquid

Liquid detergents

Powder and liquid

detergents recommended suitable for

detergents recommended for colors can be used at colors and dark

for whites can be used at dosages recommended colors can be

dosages recommended for normally soiled

used at dosages

for normally soiled

clothes. Detergents which recommended for

clothes.

do not contain bleach

normally soiled

should be used.

clothes.

Prefer liquid detergents produced for delicate clothes. Woolen and silk clothes must be washed with special woolen detergents.

Lightly Soiled
(No visible stains exist.)

Powder and liquid

Liquid detergents

Powder and liquid detergents recommended for whites can be used at dosages recommended for lightly soiled clothes.

detergents recommended for colors can be used at dosages recommended for lightly soiled clothes. Detergents which do not contain bleach should

suitable for colors and dark colors can be used at dosages recommended for lightly soiled

be used.

clothes.

Prefer liquid detergents produced for delicate clothes. Woolen and silk clothes must be washed with special woolen detergents.

4.2.8 D splayed Program T me You can see the programme duration on the display of your machine while selecting a programme. Depending on the amount of laundry you have loaded into your machine, foaming, unbalanced load conditions, fluctuations in power supply, water pressure and program settings, the programme duration is automatically adjusted while the programme is running.
SPECIAL CASE: At programme start of Cottons and Cotton Eco programmes, display shows the duration of half load, which is the most common use case. After programme starts, in 20-25 minutes actual load is detected by the machine. And if the detected load is higher than half load; washing program will be adjusted accordingly and program duration increased automatically. You may follow this change on the display.

Wash ng Mach ne / User’s Manual

13 / EN

4.3 Operating the product 4.3.1 Control panel

1 – Programme Selection Knob (Uppermost position On / Off) 2 – Display 3 – End Time Adjustment Button 4 – Programme Follow-up Indicator 5 – Start/Pause Button

6 – Auxiliary Function Button 3 7 – Auxiliary Function Button 2 8 – Auxiliary Function Button 1 9 – Spin Speed Adjustment Button 10 – Temperature Adjustment Button

4.3.2 Prepar ng the mach ne 1. Make sure that the hoses are connected tightly. 2. Plug in your machine. 3. Turn the tap on completely. 4. Place the laundry in the machine. 5. Add detergent and fabric softener.
4.3.3 Programme select on and t ps for eff c ent wash ng 1. Select the programme suitable for the type, quantity and soiling degree of the laundry in accordance with the “Programme and consumption table” and the temperature table below. 2. Use the Programme Selection knob to select the desired programme.

14 / EN

Wash ng Mach ne / User’s Manual

4.3.4 Programme and consumpt on table
EN

Auxiliary functions

Max. Load (kg) Water Consumption (l) Energy Consumption (kWh) Max. Speed Fast+ Prewash Extra Rinse Anticrease+

Program

Temperature

Eco 40-60

/
/ + 40 / / / +

90 60 40 40 *** 40 **,*** 40 *** 60 ** 60 ** 60 40 90 60 30 30 40 40 30 40 40 30 90 60 60 90

8 95 8 95 8 93 8 51,0 4 34,0 2 27,0 8 51,0 4 36,5 3 75 3 70 8 66 8 66 8 66 2 40 3,5 83 1,5 62 3,5 60 3,5 88 3,5 58 4 85 8 129 2 95 3 65 – 85

2,40 1,80 0,97 0,980 0,535 0,305 0,990 0,670 1,35 0,85 2,20 1,20 0,20 0,15 1,00 0,55 0,79 1,05 0,60 1,70 2,90 1,40 1,40 2,60

1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 800 1000 800 1000 1000 1000 1000 1000 800 600

···· ···· ····

····

··

·· * ·

··

····

Cold – 90 Cold – 90 Cold – 90
40-60 40-60 40-60 40-60 40-60 Cold – 60 Cold – 60 Cold – 90 Cold – 90 Cold – 90 Cold – 30 Cold – 40 Cold – 40 Cold – 40 Cold – 40 Cold – 40 30 – 60 20-90 Cold-60 Cold-60
90

· : Selectable

* : Automatically selected, cannot be cancelled.

** : Eco 40-60 (

) is the test programme in accordance with EN 60456:2016 and energy

label with Commission Delegated Regulation (EU) 1061/2010)

***: Eco 40-60 with 40 °C temperature selection is the test programme in accordance with EN 60456:2016/prA:2019 and energy label with Commission Delegated Regulation (EU) 2019/2014

– : See the programme description for maximum load.

Wash ng Mach ne / User’s Manual

15 / EN

C INFORMATION
· Water and power consumption may vary subject to the changes in water pressure, water hardness and water temperature, ambient temperature, type and amount of laundry, selection of auxiliary functions and spin speed, and changes in the mains voltage.
· When selecting a programme, you can see the washing duration on the display of your machine. Depending on the amount of laundry you have loaded into the machine, there might be a difference of 1 to 1.5 hours between the duration shown on the display and the actual duration of the washing programme. The duration will be corrected automatically right after the washing programme has started.
· The auxiliary functions in the table may vary according to the model of your machine. · Auxiliary function selection modes can be changed by the manufacturing company. Existing
selection modes can be removed or new selection modes can be added. · Always select the lowest appropriate temperature. The most efficient programmes in terms of
energy consumption are generally those that perform at lower temperatures and longer duration. · Noise and remaining moisture content are influenced by the spinning speed: the higher the spinning
speed in the spinning phase, the higher the noise and the lower the remaining moisture content.
Consumption Values (EN)

Temperature Selection (°C) Spin Speed (rpm) Capacity (kg) Program Duration (hh:mm) Energy Consumption(kWh/ cycle) Water Consumption(L/ cycle) Laundry Temperature (°C) Remaining Moisture Content (%)

1000

8,0