Dell EMC PowerSwitch N3200-ON Series User Guide

Dell EMC PowerSwitch N3200-ON Series
Warnings and Specifications

© 2020 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks may be trademarks of their respective owners.

N3200-ON Series Warnings and Specifications

This document lists Warnings, Regulatory information, and Specifications for the Dell EMC PowerSwitch N3200-ON Series switch.
Table 1. Document revision history

Support and documentation

• For installation instructions, see the Dell EMC PowerSwitch N3200-ON Series Installation Guide at www.dell.com/support/.
• To access the support site, go to www.dell.com/support/. To display information in your language, at the bottom of the page, select your country from the drop-down menu.

Information icon definitions:

WARNING: The Warning icon signals information about hardware handling that could result in injury.
CAUTION: The Caution icon signals information about situations that could result in equipment damage or loss of data.
NOTE: The Note icon signals important operational information.

Warnings

WARNING: To avoid electrostatic discharge (ESD) damage, wear grounding wrist straps when handling this equipment.
WARNING: Only trained and qualified personnel can install this equipment. Read the safety instructions in your Safety, Environmental, and Regulatory.
WARNING: This switch has multiple power cables. Disconnect all power cables before servicing.
WARNING: This switch has optical transceivers, which comply with the limits of Class 1 laser radiation. When working with optical fibers, follow all warning labels and always wear eye protection.
WARNING: When no cable is connected, visible and invisible laser radiation may be emitted from the aperture of the optical transceiver ports. Avoid exposure to laser radiation; do not stare into open apertures.
WARNING: Never power on the switch if no fan module is installed. (Fixed-fan switches always have a fan module installed.)
WARNING: Prevent exposure and contact with hazardous voltages. Do not attempt to operate this switch with the safety cover removed. To comply with the GR-1089 Lightning Criteria for Equipment Interfacing with AC or DC Power Ports, use an external surge protection device (SPD) at the AC or DC input of the router.
WARNING:: Equipment that provides DC input to the DC port must be certified for CCC and meet the relevant standards.
WARNING: This equipment must be earthed. Connect the power plug to a properly wired earth-ground socket outlet.

Cautions

CAUTION:Operate the equipment at an ambient temperature not higher than 45°C (113°F).
CAUTION: Stationary pluggable equipment Type-A used in a location with equipotential bonding, such as a telecommunication center, a dedicated computer room, or a restricted access area, must have installation instructions that require protective earth-ground connection verification by a skilled electrician.

CAUTION:
Illustration of the earth-ground varification Caution in German. Illustration of the power cord Caution with translations.

Notes

NOTE: If necessary, to upgrade your software or firmware images, go to the Drivers and Downloads page of your switch at www.dell.com/support/.
NOTE: For proper ventilation, position the switch with a minimum of 5 inches (12.7 cm) of clearance around the exhaust vents.
NOTE: Install the switch into a rack or cabinet before installing any additional components such as cables or optics.
NOTE: For the N3208PX-ON switch only: If you are using two external power adapters (EPAs) in a two-post front or center mount, you must have two-rack units space available in your rack. Install the switch in the bottom portion of the two-rack units and the EPA in the top portion above the switch.
NOTE: Dell EMC recommends you ground your switch. Use the switch in a common bond network (CBN). Grounding conductors must be made of copper. Do not use aluminum conductors. Coat the one-hole lug with an anti-oxidant compound before crimping. Bring any unplated mating surfaces to a clean finish and coat with an anti-oxidant before mating.
NOTE: For RoHS information, see Restricted Material Compliance.
NOTE: This device is not intended for use in the direct field of view at visual display workplaces. To avoid incommoding reflections at visual display workplaces, this device must not be placed in the direct field of view.

Table 2. N3208PX-ON and N3224T-ON

*Maximum number of PSUs available for the switch.
**Chassis weight with one PSU.

Table 3. N3224F-ON, N3224PX-ON, and N3224P-ON

*Maximum number of PSUs available for the switch.
**Chassis weight with one PSU.

Table 4. N3248X-ON, N3248TE-ON, N3248P-ON, and N3248PXE-ON

*Maximum number of PSUs available for the switch.
**Chassis weight with one PSU.

Mexico-only NOM information

The following information is in compliance with the requirements of the official Mexican standards (NOM):

Table 5. NOM

N3200-ON Series Specifications

Table 6. Environmental parameters

Table 7. Power consumption parameters

© 2020 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks may be trademarks of their respective owners.