Philips 4000 Series Micro Music System TAM4205 User Manual
User manual
Register your product and get support at www.philips.com/support
Important
Safety
Read and understand all instructions before you use this micro music system. If damage is caused by failure to follow the instructions, the warranty does not apply.
This ‘bolt of lightning’ indicates uninsulated material within the device may cause an electrical shock, For the safety of everyone in your household, please do not remove the covering. The ‘exclamation mark’ calls attention to features for which you should read the enclosed literature closely to prevent operating and maintenance problems.
WARNING: To reduce the risk of fire or electric shock, the device should not be exposed to rain or moisture and objects filled with liquids, such as vases, should not be placed on the device.
CAUTION: To prevent electric shock, fully insert the plug. (For regions with polarized plugs: To prevent electric shock, match wide blade to wide slot.)
- Never remove the casing of this apparatus
- Never lubricate any part of this apparatus.
- Never look into the laser beam inside this apparatus
- Never place this apparatus on other electrical equipment.
- Keep this apparatus away from direct sunlight. naked flames or heat
- Ensure that you always have easy access to the power cord, plug, or adaptor to disconnect the apparatus from the power
- Make sure that there is enough free space around the product for ventilation.
- Only use attachments/accessories specified by the manufacturer.
- Battery usage CAUTION — To prevent battery leakage which may result in bodily injury, property damage, or damage to the product:
- Install the battery correctly, + and – as marked on the product.
- The battery (packed or installed) shall not be exposed to excessive heat such as sunshine, fire or the like.
- Remove the battery when the product is not used for a long time.
- The product shall not exposed to dripping or splashing.
- Dono piace any source of danger on the product (e.g. liquid filled objects. lit candles).
- Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily
Notice
Any changes or modifications made to this device that are not expressly approved by MMD Hong Kong Holding Limited may void the user’s authority to operate the equipment.
Compliance
Hereby, TP Vision Europe B.V. declares that this product is in compliance with the essential requirements and other televant provisions of Directive 2014/53/ EU, You can find the Declaration of Conformity on www.philips.com/support.
Care of the enviroment
Disposal of your old product and battery
Inform yourself about the local separate collection system for electrical and electronic products and batteries. Follow local rules and never dispose of the product and batteries with normal household waste. Correct disposal of old products and batteries helps prevent negative consequences for the environment and human health.
Removing the disposable batteries
To remove the disposable batteries, see battery installation section.
Environmental information
All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer), and polyethylene (bags, protective foam sheet.)
Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local
regulations regarding the disposal of packaging materials, exhausted batteries, and old equipment.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by MMD Hong Kong Holding Limited is under license.
The making of unauthorized copies of copy-protected material, including computer programs, files, broadcasts, and sound recordings, may be an infringement of copyrights and constitute a criminal offence. This equipment should not be used for such purposes.
Care for your product
- Do not insert any objects other than discs into the disc compartment.
- Do not insert warped or cracked discs into the disc compartment.
- Remove the discs from the disc compartment if you are not using the product for an extended period of time.
- Only use microfiber cloth to clean the product.
This apparatus includes this label:
- The type plate rs located on the back of the product
Your Micro Music System
Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/support.
Introduction
With this unit, you can:
- enjoy audio from discs, USB devices, Bluetooth devices. and other external devices;
- listen to FM radio stations.
The unit supports these media formats:
What’s in the box
Check and identify the contents of your package:
- Main unit
- Remote control (with one AAA battery)
- Speaker boxes (x2)
- Printed materials
Overview of the main unit
- LED indicator
• Standby indicator: turns red when this product is switched to standby.
• Bluetooth indicator: turns blue to indicate the Bluetooth connection status.
• Switch this product on or to standby.- Display panel
• Show current status. - Dise compartment
• Connect USB storage devices.- AUDIO IN
• Connect external audio devices. - SOURCE/PAIRING
• Press to select a source: DISC. USB, TUNER, AUDIO IN, BT.
• In Bluetooth mode, press and hold for more than 2 seconds to disconnect the currently connected device and enter pairing mode.
• Start or pause play.
• Stop play.
• Erase a program.
• Skip to previous/next track.
• Search within a track/disc.
• Tune to a radio station.
• Adjust time.
• Open orclose the disc compartment.- Volume knob
• Adjust volume. - SPEAKER OUT socket
• Connect with the speakers. - AC MAINS ~
- FM antenna
• Improve FM radio reception.
Overview of the remote control
• Switch this product on or to standby.- CD
• Select CD source. - FM
• Select FM source.
• Skip to the previous/next track
• Search within a track/disc/USB
• Tune to a FM station.
• Adjust time.- Move
• Select shuffle mode to play tracks randomly.
• Select repeat mode to play a track or all tracks repeatedly. - ALBUM/PRESET
• Select a preset radio station.
• Skip to previous/next album. - INFO
• Display playback information. - SLEEP/TIMER
• Set sleep timer.
• Set alarm timer. - CLOCK
• Set the clock.
• View clock information.
• Instandby, press and hold to toggle clock display on or off.
• Program tracks.
• Program radio stations.
• Auto store radio stations.
• Mute or restore volume.- SOUND
• Select a preset sound effect. - +/- (volume)
• Adjust volume. - DIM
• Adjust display brightness.
• Stop play or erase a program.
• Press to start, pause, or resume play.- USB/AUDIO IN
• Select USB source.
• Select AUDIO IN source. - PAIRING
• Select Bluetooth source
• In Bluetooth mode, press and hold for more than 2 seconds to disconnect the currently connected device and enter pairing mode.
Get started
• Use of controls of adjustments or performance of procedures other than herein may result in hazardous radiation
Always follow the instructions in this chapter in sequence.
Connect speakers
- Insert the stripped portion of each speaker wire into the socket completely.
- For better sound quality, use the supplied speakers only.
- For the right speaker. find the sockets on the back of the main unit marked “R’.
- Insert the red wire into the red (+) socket, and the black wire into the black (-) socket.
- For the left speaker, find the sockets on the main unit marked °L’.
- Repeat step 2 to insert the teft speaker wire.
To insert each speaker wire:
- Hold down the socket flap.
- Insert the speaker wire fully.
- Release the socket flap.
Connect power
- Risk of product damage! Ensure that the bower supply voltage corresponds to the voltage printed on the back or the underside of the unit
- Risk of electne shock! Before you plug the AC power cord, make sure that the plug ts fixed securely. When you unplug the AC power cord, always pull the plug, never pull the cord.
- Before you connect the AC power cord. make sure that you have completed all the other connections.
Prepare the remote control
- Risk of product damage! When the remote: control is not used for long periods, remove the battenes.
- Batteries contain chemical substances. so
To insert the remote control battery:
- Openthe battery compartment.
- Insert the supplied AAA battery with correct polarity (+/-) as indicated.
- Close the battery compartment
Press
Switch to standby mode
Press
• In standby, you may press and hold CLOCK to toggle clack display on or off.
- The product switches to standby mode after 15 minutes inactive
- To achieve the efficient energy saving performance, unplug any external electronic device from the USB port when the device is not in use
Set the clock
- In power on mode, press and hold CLOCK for more than 2 seconds to enter the clock setting mode.
- Press
- Press
- Press
- To view clock in power-on mode. press briefly CLOCK.
- Instandby, you may press and hold CLOCK to toggle clock display on or off.
- If clock display is turned on in standby, power consumption increases.
Play
Play from disc
- Press CD to select CD source.
- Press
- Insert a disc with the label side up
- Press
• Make sure that the USB device contains playable audio content.
- Insert a USB device into the
- Press USB to select the USB source.
Control play
| Start, pause, or resume play. | |
| Stop play. | |
| Select an aloum ora folder. | |
| Press to skip to the previous or next track. Press and hold to search backward/forward within a track. | |
| MODE | Play a track or all tracks repeatedly. Play tracks randomly. |
| +/+ | Increase or decrease the volume. |
| Mute or unmute sound. | |
| SOUND | Select a preset sound equalizer. |
| DIM | Adjust display brightness. |
| INFO | Show playback information. |
Skip tracks
For CD:
Press
For MP3 disc and USB:
- Press
- Press
Program tracks
This function allows you to program 20 tracks in the desired sequence.
- In stop mode, press PROG/SCAN to activate the program mode.
- For MP3 tracks, press
- Press
- Repeat steps 2 to 3 to program more tracks.
- Press
To erase the program
Press
Play from Bluetooth-enabled devices
- Compatibility with all Bluetooth devices is nol guaranteed.
- Any obstacle between the unit and the device can reduce the operational range.
- The effective operation range between this. unit and your Bluetooth enabied device is approximately 10 meters (30 feet)
- The unit can memorize up to & previously connected Bluetooth devices.
- Press
- On your device that supports Advanced Audio Distribution Profile (A2DP), enable Bluetooth and search for Bluetooth devices that can be paired (refer to the user manual of the device).
- Select “Phitips M4205″on your
Bluetooth enabled device and if necessary input ‘0000’ as the paring password.
• IF you fail to find “Philips M4205 ° or cannot pair with this product, press and hold PAIRING for more than 2 seconds to enter pairing mode. - Play audio on the connected device.
Bluetooth enabled device to this product.
To disconnect the Bluetooth-enabied device:
- Deactivate Bluetooth on your device.
- Press and hold PAIRING for 2 seconds to enter pairing mode.
Listen to FM radio
Tune to a radio station
- Position the antenna as far as possible from TV, or other ractiathon source.
- For optimal reception, fully extend and
- Press FM to select FM source.
- Press and hold
- Repeat step 2 to tune to more stations.
To tune to a weak station:
Press
Store radio stations automatically
Note
- You can store a maximum of 10 FM radio Stabons.
- Press FM to select FM source.
- Press and hold PROG/SCAN for more than 2 seconds.
Store radio stations manually
- Tune to an FM radio station.
- Press PROG/SCAN to activate program mode.
[POT is displayed. - Press
- Repeat steps 1-3 to program more stations.
- To overwiite a programmed station. store another station In ts place
Select a preset radio station
In FM mode, press
Adjust sound
The following operations are applicable to all supported media.
Select a preset sound effect
- Press SOUND fepeatedly to select a preset sound effect.
Adjust volume level
- Onthe remote control, press +/- (volume) repeatedly.
- On the main unit, rotate the volume knob.
Mute sound
- Press
Other features
Set the alarm timer
This product can be used as an alarm clock. You can select the disc, radio, or Mp3 files on a USB storage device as alarm source.
- Alarm timer is not available in AUDIO IN mode.
- IFCD/US6 source ts selected, but no disc is placed of no USB device is connected. the radio source is selected automatically.
- Make sure that you have set the clock.
- Instandby mode, press and hold
SLEEP/TIMER for more than 2 seconds. - Press
- Press
- Press
- Press
Activate/deactivate alarm timer
In standby mode, press SLEEP/TIMER sepeatedly to activate or deactivate timer.
- Instandby, you may press and hold CLOCK to toggle clock display on or off.
Set the sleep timer
This music system can switch to standby automatically after a set period of time.
- When the music system is turned on, press SLEEP/TIMER repeatedly to select a set period of time (in minutes).
To deactivate sleep timer
- Press SLEEP/TIMER repeatedly until [OFF] (sleep off) is displayed.
Listen to an external
You can listen to an external device through this unit with an MP3 link cable.
- Connect an MP3 tink cable (not supplied) between:
• AUDIO IN jack (3.5 mm) on the product,
• and the headphone jack on an external device. - Press AUDIO IN repeatedly to select AUDIO IN source.
- Start to play the device (see the device user manual).
Charge your devices
With this micro music system, you can charge your external devices, such as your cell phone, MP3 player or other mobile devices.
- Use.a USB cable to connect the
USB socket of this product with the
USB socket of your devices. - Connect the product to power.
Product information
- Product information ts subject to change without prior notice.
Specifications
- Rated output power (Amplifier): Total 60W (max.)
- Acoustic frequency response: SOHz – 20KHz
- Speaker driver: 2 x 4” woofer range, 6Q 2 x 20mm tweeter range 82
- Bass enhancement: 2 x bass port
- Support dise type: CD-DA, CD-R, CDRW. MP3-CD (8/12 cm)
- Bluetooth version: V4.2
- Bluetooth supported profiles: A2DP V1.2, AVRCP V1.0
- Bluetooth frequency band / Output power: 2.402GHz ~ 2.480GHz ISM Band / <s 4dBm (Class 2)
- USB playback: Type A, USB Direct 2.0, 5V/ 14, MSC file format, FAT 16/32,
- Support USB up to 32G
- USB charging: 24 max (Standby); SOOmA max (USB source), 1A max (BT/Radio/ CD/Audio in source)
- Actual charging current depends on the mobile devices.
- Tuner frequency range: FM 875-108MHz
- Preset stations: 10
- AUDIO IN input level: 70Omv +100mV RMS
- Power: 100 – 240V~, 50/60 Hz (AC Input)
- Operation power consumption: 30W
- Standby power consumption:
- < 0.5W (clock display off)
- Dimensions (W x H x D): 220 x 104 x 2315 mm (Main unit). 150 x 2413 x173 mm (Speaker box)
- Weight: 168ke (Main unit), 2x 1.78 kg (Speaker box)
USB playability information
Compatible USB devices:
- USB flash memory (USB2.0 or USBI.1)
- USB flash players (USB2.0 or USB1,1)
- memory cards (requires an additional card reader to work with this unit)
Supported USB formats:
- USB or memory file format: FATI6, FAT32 (sector size: 512 bytes)
- MP3 bit rate (data rate); 32-320 Kbps and variable bit rate
- Directory nesting up to a maximum of 8 levels
- Number of albums/ folders: maximum 99
- Number of tracks/titles: maximum 999
- File name in Unicode UTF8 (maximum length: 32 bytes)
Unsupported USB formats:
- Empty albums: an empty aloum is an album that does not contain MP3 files, and will not be shown in the display.
Supported MP3 disc formats
- 1809660, Jotiet
- Maximum title number: 128 (depending on file name length)
- Maximum album number: 99
- Supported sampling frequencies: 32 kHz, 44.1 kHz, 48 kHz
- Supported Bit-rates: 32~256 (kbps).variable bit rates
Troubleshooting
- To keep the warranty valid, never try to repair the system yourself.
If you encounter problems when using this device, check the following points before requesting service. If the problem remains unsolved, go to the Philips Web page (www.philips.com/support), When you contact Philips, make sure that the device is nearby and the model number and serial number are available,
No power
- Make sure that the AC power cord of the device is connected properly.
- Make sure that there is power at the AC outlet.
- Asa power-saving feature, the system switches off automatically 15 minutes after track play reaches the end and no control is operated.
No sound or poor sound
- Adjust the volume.
- Check that the speakers are connected correctly.
- Check if the stripped speaker wires are clamped.
No response from the unit
- Disconnect and reconnect the AC power plug, then turn on the unit again.
- Sa power-saving feature, the system switches off automatically 15 minutes after track play reaches the end and no control is operated.
Remote control does not work
- Before you press any function button, first select the correct source with the remote control instead of the main unit.
- Reduce the distance between the remote control and the unit.
- Insert the battery with its polarities (+/- signs) aligned as indicated.
- Replace the battery.
- Aim the remote control directly at the sensor on the front of the unit.
No disc detected
- Insert a disc.
- Check if the disc is inserted upside down.
- Wait until the moisture condensation at the lens has cleared.
- Replace or clean the disc.
- Use a finalized CD or correct format disc.
Cannot display some files in USB device
- The number of folders or files in the USB device has exceeded a certain limit. This phenomenon is not a malfunction,
- The formats of these files are not supported.
USB device not supported
- The USB device is incompatible with the unit. Try another one.
Poor radio reception
- Increase the distance between the unit and your TV or other radiation sources.
- Fully extend the radio antenna.
Music playback is unavailable on this unit even after successful Bluetooth connection.
- The device cannot be used to play music through this unit wirelessly.
The audio quality ts poor after connection with a Bluetooth-enabled device.
- The Bluetooth reception is poor. Move the device closer to this unit of remove any obstacle between them.
Bluetooth cannot be connected with this untt.
- The device does not support the profiles required for this unit.
- The Bluetooth function of the device is not enabled. Refer to the user manual of the device to find out how to enable the function.
- This unit is not in pairing mode.
- This unit is already connected with another Bluetooth-enabled device.
- Disconnect that device and then try again.
The paired mobile device connects and disconnects constantly.
- The Bluetooth reception is poor. Move the device closer to this unit or remove any obstacle between them.
- Some mobile phones may connect and disconnect constantly when you make or end calls. This does not indicate any malfunction of this unit.
- Forsome devices, the Bluetooth connection may be deactivated automatically as a power-saving feature. This does not indicate any malfunction of this unit.
Timer does not work
- Set the clock correctly.
- Switch on the timer.
Clock/timer setting erased
- Power has been interrupted or the power cord has been disconnected.
- Reset the clack/timer.
How to keep clock display on or off in standby?
- In standby, press and hold CLOCK to toggle clock display on or off.
Specifications are subject to change without notice
TAM4205_12_UM_V1.0
