Philips 3000 Series R3306 Clock Radio User Manual

PHILIPS 3000 Series R3306 Clock Radio

Important Safety

  • Read these instructions.
  • Heed all warnings.
  • Follow all instructions.
  • Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
  • Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
  • Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the clock radio.
  • Only use attachments/accessories specified by the manufacturer.
  • Unplug this apparatus during lightning storms or when unused for long periods of time.
  • Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
  • Battery usage CAUTION – To prevent battery leakage which may result in bodily injury, property damage, or damage to the clock radio:
    • Install all batteries correctly, + and – as marked on the unit.
    • Remove batteries when the unit is not used for a long time.
    • The battery shall not be exposed to excessive heat such as sunshine, fire or the like.
  • This clock radio shall not be exposed to dripping or splashing.
  • Do not place any sources of danger on the clock radio (e.g. liquid filled objects, lighted candles).
  • Where the plug of the Direct Plug-in Adapter is used as the disconnect device, the disconnect device shall remain readily operable.

Notice
Any changes or modifications made to this device that are not expressly approved by MMD Hong Kong Holding Limited may void the user’s authority to operate the product. Hereby, TP Vision Europe B.V. declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. You can find the Declaration of Conformity on www.philips.com/support.

This product complies with the radio interference requirements of the European Community.
This product is designed and manufactured with high-quality materials and components, which can be recycled and reused.

This symbol means the product must not be discarded as household waste and should be delivered to an appropriate collection facility for recycling. Follow local rules and never dispose of the product and rechargeable batteries with normal household waste. Correct disposal of old products and rechargeable batteries helps prevent negative consequences for the environment and human health.

This symbol means that the product contains batteries covered by European Directive 2013/56/EU which cannot be disposed of with normal household waste. Inform yourself about the the local separate collection system for electrical and electronic collection system for electrical and electronic products and batteries. Follow local rules and never dispose of the product and batteries with normal household waste. Correct disposal of old products and batteries helps prevent negative consequences for the environment and human health.

Your clock radio

Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/support.

Introduction

With this clock radio, you can

  • listen to FM radio
  • set two alarms to ring at different times.
What’s in the box

Check and identify the contents of your package:

• Main unit
• Power adaptor
• Quick start guide
• Safety sheet
• Warranty

Overview of the clock radio
  1. Turn on or switch to standby.
  2. PRESET / SET TIME
    • Store radio stations in memory.
    • Select a preset radio station.
    • Set time.
  3. HR / MIN / TUN
    • Set hour and minute.
    • Tune to FM radio stations.
  4. SNOOZE / BRIGHTNESS
    • Snooze alarm.
    • Adjust display brightness.
  5. Display panel
    • Display current status.
  6. SLEEP / SCAN
    • Set the sleep timer.
    • Scan and store radio stations automatically.
  7. AL1 / AL2 / – VOL +
    • Set alarm.
    • Adjust volume.

Get started

Always follow the instructions in this chapter in sequence.

Install batteries

The batteries can only back up clock and alarm settings.

Caution
• Risk of explosion! Keep the batteries away from heat, sunshine or fire. Never discard batteries in fire.
• Batteries contain chemical substances, so they should be disposed of properly.
• Do not mix battery types: e.g. alkaline with carbon zinc. Only use batteries of the same type for the set.

Insert 2 AAA batteries (not provided) with correct polarity (+/-) as illustrated.

Connect power

• Risk of product damage! Make sure that the power voltage corresponds to the voltage printed on the back or underside of the clock radio.
• Risk of electrical shock! When you unplug the power cord, always pull the plug from the socket. Never pull the cord.
• The type plate is located at the bottom of the clock radio.

Connect the power adaptor to the wall outlet.

Set time

You can only set time in standby mode.

  1. In standby mode, press and hold SET TIME for 2 seconds.
  2. Press HR to set hour and MIN to set minute, then press SET TIME to confirm. The time is set.

Listen to FM radio

• Keep the clock radio away from other electronic devices to avoid radio interference.
• For better reception, fully extend and adjust the position of the FM antenna.

Tune to FM radio stations
  1. Press to turn on the clock radio.
  2. Press and hold for 2 seconds. The clock radio tunes to a station with strong reception automatically.
  3. Repeat Step 2 to tune to more radio stations.

To tune to a station manually:
Press TUN repeatedly to select a frequency

Store FM radio stations automatically

In FM tuner mode, press and hold SCAN for more than 2 seconds.

The unit stores all the available FM radio stations automatically and broadcasts the first station.

Store FM radio stations manually
  1. In FM tuner mode，tune to an FM radio station.
  2. Press and hold PRESET for 2 seconds to activate programming mode. The preset number begins to blink.
  3. Press TUN repeatedly to select a number.
  4. Press PRESET again to confirm.
  5. Repeat steps 1 to 4 to store more FM radio stations.
    Tip: To remove a pre-stored station, store another station in its place.
Select a preset radio  station

Option A:
In FM tuner mode, press PRESET repeatedly to select a preset number.
Option B:

  1. In FM tuner mode, press PRESET.
  2. Press TUN to select a preset radio station.

Adjust volume
While listening, press VOL to adjust volume.

Other features

Set alarm time

Set alarm
• You can only set the alarm in standby mode.
• Make sure that you have set the clock correctly.

  1. In standby mode, press and hold AL1 or AL2 for 2 seconds to set alarm time.
  2. Press HR to set hour and MIN to set minute, then press AL1 or AL2 to confirm.

Select alarm source
You can select FM radio or buzzer as the alarm source by pressing AL1 or AL2 in standby mode.
The corresponding alarm icon lights up.

Activate/deactivate alarm timer
Press AL1 or AL2 repeatedly to activate or deactivate the alarm timer.

  • If the alarm timer is activated, the alarm indicator turns on.
  • If the alarm timer is deactivated, the alarm indicator turns off.
  • The alarm repeats ringing for the next day.
  • To stop the alarm, press the coresponding AL1 or AL2.

Snooze the alarm
When the alarm sounds, press SNOOZE.
The alarm snoozes and repeats ringing 9 minutes later.

Adjust display brightness

Press BRIGHTNESS repeatedly to select different brightness levels:

• High
• Medium
• Low

Troubleshooting

Warning: Never remove the casing of the product.

To keep the warranty valid, never try to repair the device yourself. If you encounter problems when using this device, check the following points before requesting service. If the problem remains unsolved, go to the Philips webpage www.philips.com/support. When you contact Philips, make sure that the device is nearby and the model number and serial number are available.

No power
• Make sure that the AC power plug of the unit is connected properly.
• Make sure that there is power at the AC outlet.

No sound
• Adjust the volume.

No response from the unit
Disconnect and reconnect the AC power plug, then turn on the unit again.

Poor radio reception
• Keep the clock radio away from other electronic devices to avoid radio interference.
• Fully extend and adjust the position of the antenna.

Alarm does not work
Set the clock/alarm correctly.

Clock/alarm setting erased
• Power has been interrupted or the power plug has been disconnected.
• Reset the clock/alarm.
• Replace the backup batteries.

2021 © MMD Hong Kong Holding Limited. All rights reserved. Specifications are subject to change without notice.
Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. This product has been manufactured by and is sold under the responsibility of MMD Hong Kong Holding Limited or one of its affiliates, and MMD Hong Kong Holding Limited is the warrantor in relation to this product.