Makita Grass Trimmer Instruction Manual

Makita Grass Trimmer Instruction Manual

SPECIFICATIONS

  • Due to our continuing program of research and development, the specifications herein are subject to change without notice.
  • Specifications may differ from country to country.
  • Weight according to EPTA-Procedure 01/2014

Approved power unit

Wear protective helmet, eye and ear protection!

This attachment is approved to use only with the following power unit(s):

  • DUX60 Cordless multi function power head
  • DUX18 Cordless multi function power head
  • UX01G Cordless multi function power head
  • EX2650LH Multi function power head Wear eye and ear protection. Protective gloves must be worn!

WARNING: Never use the attachment with non-approved power unit. Non-approved combination may cause serious injury.

Symbols

The following symbols are used on the attachment and this instruction manual. Understand these definitions.

Intended use
For EM408MP
This attachment is designed only for the purpose of cutting grass, weed, bushes and undergrowth in conjunction with an approved power unit. Never use the attachment for the other purpose. Abusing the attachment may cause serious injury.

For EM409MP
This attachment is designed only for the purpose of trimming grass and light weed in conjunction with an approved power unit. Never use the attachment for the other purpose. Abusing the attachment may cause serious injury.

WARNING: Read the instruction manual of the attachment as well as this instruction manual before using. Failure to follow the warnings and instructions may result serious injury.

SAFETY WARNINGS

Grass trimmer safety warnings

WARNING: Read all safety warnings, instructions, illustrations and specifications provided with this machine. Failure to follow all instructions listed below may result in fire and/or serious injury to the operator and/or bystanders.

Save all warnings and instructions for future reference.
The term “grass trimmer” and “machine” in the warnings and precautions refer to the combination of the attachment and the power unit. The term “motor” in the warnings and precautions refers to the engine or electric motor of the power unit.

General safety

  1. First-time or inexperienced operator should ask the dealer for training in all operation of the machine. Never allow children, persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge or people unfamiliar with the instructions to use the machine.
  2. It is recommended only to lend the machine to people who have proven to be experienced. Always hand over the instruction manual.
  3. Stay alert, watch what you are doing and use common sense when operating the machine. Do not use the machine while you are tired, ill, or under the influence of drugs, alcohol or medication. A moment of inattention while operating the machine may result in serious personal injury.
  4. Avoid using the machine in bad weather conditions especially when there is a risk of lightning.
  5. Follow your national and local regulation for use of outdoor power machines.

Intended use of machine
This machine is only intended for cutting grass, weeds, bushes and undergrowth. Never use the machine for any other purpose such as edging or hedge cutting. Use for unintended purpose may result in serious injury.

Personal protective equipment

  1. Always wear heavy, long pants, sturdy boots, gloves, and a long-sleeve shirt. Do not wear loose clothing, jewellery, short pants, sandals, or go barefoot. Secure hair so it is above shoulder level.
  2. Always wear a helmet where there is a risk of falling objects.
  3. Always wear protective goggles to protect your eyes from injury when using the machine. The goggles must comply with ANSI Z87.1 in the USA, EN 166 in Europe, or AS/NZS 1336 in Australia/New Zealand. In Australia/New Zealand, it is legally required to wear a face shield to protect your face, too. It is an employer’s responsibility to enforce the use of appropriate safety protective equipment’s by the tool operators and by other persons in the immediate working area.
  4. Wear ear protection, such as ear muffs. Exposure to noise can cause hearing loss.
  5. Always wear sturdy shoes with a non-slip sole. This protects your feet against injuries and ensures a good footing.
  6. Wear a dust mask as necessary.
  7. Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.

Preparation before use

  1. Before use, always check the machine is safe for operation:
    — Check for fuel leaks.
    — Make sure all fasteners are in place and secure.
    — Replace damaged parts.
    — Make sure the cutting tool is properly installed and securely fastened.
    — Make sure the cutting tool guard is properly attached in the position as described in this manual.
    — Check the throttle trigger, lock-off lever and other control switch for smooth action and proper function.
    — Clean the handles for proper control of the machine.
    — Make sure the handles are installed as described in this manual.
    Failure to follow those instructions may cause serious injury.
  2. Use a sharp blade. Discard blades that are bent, warped, cracked, broken, chipped or damaged in any way. A dull blade is more likely to snag and kickback.
  3. Always use all required parts for fixing the blade properly. Improper fixing parts can cause the blade to fly off and seriously injure the operator and/or bystanders.

Electrical and battery safety

  1. Do not expose the machine, battery, or charger to rain or wet conditions. Water entering the tool will increase the risk of electric shock.
  2. Do not charge battery in rain, or in wet locations.
  3. Do not replace the battery in the rain.

Refuelling

  1. Stop the engine before refuelling. Keep away from open flames and sparks. Never smoke during refuelling. Otherwise fire and/or explosion may result.
  2. Refuel outdoors. Refuelling in a closed room can cause explosion of fuel vapor.
  3. Avoid contact with fuel or engine oil. Do not inhale fuel vapor. If fuel or oil spills, wipe it off from the machine and/or ground immediately. If fuel spills on your clothes, change it immediately to prevent it from catching fire.
  4. After refuelling, carefully tighten the fuel tank cap and check for fuel leak. Move at least 3 m (10 feet) away from the fuelling source and site before starting engine.
  5. Only transport and store fuel in approved containers. Keep children away from the stored fuel.

Starting up the machine

  1. Keep children, bystanders and pets at least 15 m (50 feet) away, when starting up or using the machine. Additionally, bystanders should wear eye protection, as there is still a risk of injury from thrown objects. Otherwise bystanders’ unexpected action or blade kickback may cause serious injury to the operator and/or bystanders.
  2. Start and operate the machine only outdoors in a well ventilated area. Operation in a confined or poorly ventilated area can result in death due to suffocation or carbon monoxide poisoning.
  3. Before starting, make sure that the cutting tool has no contact with hard objects such as branches, stones etc. as the cutting tool will revolve when starting.
  4. If the cutting tool rotates at idle, adjust the idle speed so that it stops at idle. Otherwise unintentional contact with moving cutting tool may result in serious injury.
  5. Stop the motor immediately if you notice any trouble.
  6. Make sure there are no electrical cables, water pipes, gas pipes etc. that could cause a hazard if damaged by use of the machine.

Transportation

  1. Stop the motor during transport. Otherwise unintentional start-up may cause injury.
  2. When transporting the machine, always attach the cover to the cutting blade. Contact with bare blades results in injury.
  3. Ensure safe position of the machine during car transportation to avoid fuel leakage.
  4. Lift the entire machine from the ground when carrying the machine. Dragging the machine causes fuel tank damage and fuel leakage, resulting in fire.

Operation

  1. Only use the machine in good light and visibility. Use in the dark or poor visibility area may cause unexpected accident.
  2. Avoid using the machine when it is hard to keep your balance, for example, working on a steep surface or windy day.
  3. During operation, never stand on an unstable or slippery surface or a steep slope. During the cold season, beware of ice and snow and always ensure secure footing.
  4. If you are approached, stop the motor. Otherwise the rotating cutting tool may hit the bystander and result in serious injury.
  5. Clear the working area before operation. Remove all objects such as rocks, broken glass, nails, wire, or string, which can be thrown or become entangled in the cutting attachment. Foreign particles may damage the cutting tool and can cause dangerous kickback.
  6. To control the machine steadily, do the following during operation:
    — Hold the machine with both hands firmly on your right side.
    — Hang the machine on your shoulder(s) with the shoulder harness.
    — Ensure a safe footing. Never work on a ladder or in a tree.
    — Avoid over-reach.
    — Keep cutting tool below waist level.
    — Keep all parts of your body away from the rotating cutting tool and hot surface.
    Those action reduces the risk of injury.
  7. If weeds or branches get caught between the cutting tool and guard, always stop the motor before clearing. Otherwise unintentional blade rotation may cause serious injury.
  8. Never drop or throw the machine, unless an emergency. If the machine drops or hits something, immediately check for fuel leakage, safety devices and other damages. Operating an malfunctioned machine may cause injury and/ or fire.
  9. Inspect the cutting tool frequently, or immediately after it hits a stone or other hard objects. If the cutting tool breaks during operation, the broken piece may fly and cause injury.
  10. Stop the motor when inspecting, cleaning or replacing the cutting tool. Otherwise the cutting tool may rotate unexpectedly and result in serious injury.
  11. Maintain proper control until the cutting tool stops completely, when stopping the motor or releasing the throttle trigger. A coasting blade can cause injury.
  12. Before starting the cutting operation, wait until the cutting tool attains enough speed for cutting. It reduces the risk of kickback and entangling weeds.
  13. Take a rest to prevent loss of control caused by fatigue. We recommend to take a 10 to 20-minute rest every hour.
  14. Stop the motor and place it in safe location, when resting or leaving the machine. It prevents unexpected accident.
  15. Do not touch the engine and its muffler or do not put them onto combustible materials, while the engine runs or just after stopping it, as they are hot. Burn and/or fire may result.
  16. Do not operate the tool in bad weather or if there is a risk of lightning.

Cutting Tools

  1. Use a suitable cutting tool for your work.
    — Nylon cutting heads (string trimmer heads) are suitable for trimming lawn grass.
    — Metal blades are suitable for cutting weeds, high grasses, bushes, shrubs, underwood, thicket, and the like.
    Always use the cutting tool guard properly suited for the cutting tool used.
  2. When using a nylon cutting head, use only flexible, non-metallic line recommended in this manual. Never use wire or wire rope. They can break off and become a dangerous projectile.
  3. Never use metal multi-piece pivoting chains, flail blades or blades not recommended in this manual. Otherwise serious injury may result.
  4. When handling the metal blade, always wear gloves and put the blade cover on the blade. The blade can cut bare hands.
  5. When using metal blades, avoid “kickback” and always prepare for an accidental kickback. See the section Kickback.

Kickback (blade thrust)
Kickback (blade thrust) may occur when the spinning blade contacts an object that it does not immediately cut. It can be violent enough to cause the unit and/or operator to be propelled in any direction, and possibly lose control of the unit, resulting in serious injury. Kickback can occur without warning if the blade snags, stalls or binds and is more likely to occur in areas where it is difficult to see the material being cut.
Kickback occurs particularly when applying the blade segment between 12 and 2 o’clock to solids, bushes and trees with 3 cm or larger diameter. ► Fig.1
To avoid kickback:

  1. Apply the segment between 8 and 11 o’clock.
  2. Swing the tool evenly in half-circle from right to left, like using a scythe. This allows the proper segment of blade to contact plants to be cut.
  3. Never apply the segment between 12 and 2 o’clock.
  4. Never apply the segment between 11 and 12 o’clock and between 2 and 5 o’clock, unless the operator is well trained and experienced and does it at his/her own risk.
    ► Fig.2
  5. Never use cutting blades close to solids, such as fences, walls, tree trunks and stones.
  6. Never use cutting blades vertically, for such operations as edging and trimming hedges.
  7. Avoid using the tool in areas where it is difficult to see the object being cut.

Vibration
Exposing to excessive vibration injures blood vessels or nervous system of the operator and causes the following symptoms in the fingers, hands or wrists: “Falling asleep” (numbness), tingling, pain, stabbing sensation, or alteration of skin colour or of the skin. If any of these symptoms occur, see a physician.
To reduce the risk of “white finger disease”, keep your hands warm during operation and well maintain the machine and accessories.

Maintenance

  1. Have your machine serviced by our authorized service centre using only identical replacement parts. Use only identical spare parts and accessories supplied by MAKITA. Incorrect repair and poor maintenance can shorten the life of the machine and increase the risk of accidents.
  2. Never alter or remove any components of the machine. It may cause fire and/or serious injury.
  3. After use, clean the machine and check all screws and nuts for tightness.
  4. Check the condition of the cutting tool, cutting tool guard and shoulder harness. The cutting blade must be sharp. Never straighten or weld damaged cutting tools.

Storage

  1. Before storing the machine, perform full cleaning and maintenance. Remove the battery cartridge. Empty the fuel tank. Attach the cover to the cutting blade.
  2. Store the machine in a dry and high or locked location out of reach of children.
  3. Do not prop the machine against something, such as a wall. Otherwise it may fall suddenly and cause an injury.

Other instructions

  1. Pay attention to the environment. Avoid unnecessary throttle operation for less pollution and noise emissions. Adjust the carburettor correctly.
  2. Do not operate the engine with faulty exhaust muffler.

First Aid

  1. In case of accident make sure that a first-aid box is available in the vicinity of the cutting operations. Immediately replace any item taken from the first aid box.
  2. When asking for help, give the following information:
    — Place of accident
    — What happened
    — Number of injured persons
    — Kind of injuries
    — Your name

Additional safety instructions

  1. To avoid accident, leave more than 15m (50 ft) distance between operators when two or more operators work in one area. Also, arrange a person to observe the distance between operators. If someone or an animal enter the working area, immediately stop the operation.
  2. Only use the cutting tools that are marked with a speed equal or higher than the speed marked on the tool.
  3. Be sure to remove the cover on the cutting blade before operation.

PARTS DESCRIPTION

EM408MP
► Fig.3:

  1. Cap
  2. Pipe
  3. Protector (universal type)
  4. Protector extension
  5. Cutter

EM409MP
► Fig.4:

  1. Cap
  2. Pipe
  3. Protector (narrow type)
  4. Cutter

ASSEMBLY

WARNING: Before assembling or adjusting the equipment, switch off the motor and remove the spark plug cap or battery cartridge. Otherwise the cutting tool or other parts may move and result in serious injury.

WARNING: Before handling cutting blade, wear protective gloves. During the assembly or adjustment, your fingers may contact with the cutting blade and it may cause serious injury.

WARNING: When assembling or adjusting the equipment, always put it down. Assembling or adjusting the equipment in an upright position may result in serious injury.

WARNING: Follow the warnings and precautions in the chapter “SAFETY WARNINGS” and the instruction manual of the power unit.

Correct combination of the cutting tool and the protector

CAUTION: Always use the correct combination of cutting tool and protector. The wrong protector may
not protect you from flying debris and stones. It can also affect the balance of the tool and result in serious personal injury.

Installing the protector (cutting tool guard)

WARNING: Do not use a cutting tool without an appropriate protector at any time.

WARNING: Always use the cutting tool with the correct combination of the protector. Otherwise contact with a cutting tool may cause serious injury.

NOTICE: Periodically tighten the bolts on the protector. Tighten the right and left bolts evenly so that the gap between the clamp and the protector is constant.

Protector (universal type)

CAUTION: Make sure to push in the protector extension until it is fully inserted. Otherwise the protector extension may fall and result in personal injury.

CAUTION: Be careful not to injure your self with the cutter mounted on the protector extension.

Fix the protector to the clamp with bolts.
► Fig.5:

  1. Clamp
  2. Protector

To install the protector extension, insert the protector extension to the protector and then snap the clips on. Make sure that the tabs on the protector extension fit into the slots on the protector.

► Fig.6:

  1. Protector (universal type)
  2. Clip
  3. Protector extension
  4. Cutter (inside)
  5. Slot
  6. Tab

To remove the protector extension from the protector, unclasp the clips and pull the protector extension out.
NOTE: The cutter on the protector extension keeps the nylon cord best length for cutting.

Protector (narrow type)
CAUTION: Be careful not to injure yourself with the cutter mounted on the protector.

Attach the protector to the clamp using bolts.

► Fig.7:

  1. Clamp
  2. Protector
  3. Cutter

NOTE: The cutter on the protector keeps the nylon cord best length for cutting.

Installing the cutting tool

CAUTION: Be sure to use genuine MAKITA cutting tools.
CAUTION: Be sure to remove the hex wrench after installation.
NOTE: When installing the cutting tool, turn the tool upside down for ease of the procedure.

Installing the metal blade
For EM408MP

CAUTION: When handling the metal blade, always wear gloves and put the blade cover on the blade.
CAUTION: The outside diameter of the metal blade must be 230 mm (9). Never use any blades larger than 230 mm (9) in outside diameter.
CAUTION: The metal blade must be well polished, free of cracks or breakage. If the metal blade hits against a stone during operation, stop the motor and check the blade immediately.
CAUTION: Polish or replace the metal blade every three hours of operation.
CAUTION: Always use the supplied wrench(as) to remove or to install the blade.

Applicable blade

  1. Make sure that the receive washer is attached to the shaft.
  2. Insert the hex wrench through the hole in the gear case to lock the shaft. Rotate the shaft until the hex wrench is fully inserted.
  3. Mount the metal blade onto the receive washer.
  4. Install the clamp washer and cup, and then tighten the nut securely. Tightening torque: 16 – 23 Nm
  5. Remove the hex wrench.

► Fig.8:

  1. Nut
  2. Cup
  3. Clamp washer
  4. Metal blade
  5. Receive washer
  6. Shaft
  7. Hex wrench

► Fig.9:

  1. Socket wrench
  2. Hex wrench
  3. Tighten Make sure that the arrows on the blade and protector indicate the same way.

► Fig.10:

  1. Arrow

To remove the metal blade, follow the installation procedure in reverse.

NOTE: The resin part on the blade fastening nut wears out in course of time. Replace the nut if there appears any wear or deformation.

Installing the nylon cutting head
CAUTION: If the nylon cutting head hits against a stone during operation, stop the motor and check the nylon cutting head immediately.
► Fig.11:

  • Nylon cutting head
  • Receive washer
  • Shaft
  • Hex wrench
  • Tighten
  1. Make sure that the receive washer is attached to the shaft.
  2. Insert the hex wrench through the hole in the gear case.
  3. Screw the nylon cutting head onto the shaft.
  4. After installing nylon cutting head, remove the hex wrench.
    To remove the nylon cutting head, turn it clockwise while holding the receive washer with the hex wrench.

Installing plastic blade
Optional accessory

CAUTION: If the plastic blade accidentally impacts a rock or hard object during operation, stop the tool and inspect for any damage. If the plastic blade is damaged, replace it immediately. Use of a damaged cutting tool could result in serious personal injury.

CAUTION: Be sure to remove the hex wrench after installation.
NOTICE: Be sure to use genuine Makita plastic blade.

► Fig.12:
1. Plastic blade 2. Receive washer 3. Shaft 4. Hex wrench 5. Tighten

  1. Make sure that the receive washer is attached to the shaft.
  2. Insert the hex wrench through the hole on the gear case and rotate the spindle until the spindle is locked.
  3. Place the plastic blade onto the threaded spindle directly and tighten.
  4. Remove the hex wrench. To remove the plastic blade, turn it clockwise while holding the receive washer with the hex wrench.

Mounting the attachment pipe

CAUTION: Always check that the attachment pipe is secured after installation. Improper installation may cause the attachment falling off from the power unit and cause personal injury.
Mount the attachment pipe to the power unit.

  1. Turn the lever of the power unit toward the attachment side.
    ► Fig.13: 1. Lever
  2. Remove the cap of the attachment. Align the pin with the arrow mark and insert the attachment pipe until the release button pops up.
    ► Fig.14: 1. Release button 2. Arrow mark 3. Pin
  3. Turn the lever toward the power unit side.
    ► Fig.15: 1. Lever
    Make sure that the surface of the lever is parallel to the pipe. To remove the pipe, turn the lever toward the attachment side and pull the pipe out while pressing down the release button.
    ► Fig.16: 1. Release button 2. Lever 3. Pipe

OPERATION

WARNING: Follow the warnings and precautions in the chapter “SAFETY WARNINGS” and the instruction manual of the power unit.
WARNING: If the cutting tool moves at idle, adjust the idle speed of the engine down. Otherwise you cannot stop the cutting tool by throttle off and it may cause serious injury.

Adjusting the hanger position and shoulder harness

For DUX60 Cordless multi function power head, EX2650LH Multi function power head

WARNING: Do not use the tool if you cannot adjust the hanger position and shoulder harness length within the range as illustrated. Using the tool with improper weight balance may bring the cutting tool upward and result in personal injury.

When replacing an accessory with another, the weight balance of the equipment may change. In such case, adjust the hanger position and shoulder harness length as follows.
► Fig.17: 1. Hanger
To change the hanger position, loosen the fixing screw on the hanger and then move the hanger. Adjust the hanger position and shoulder harness length so that:

  • the hanger positions 750 mm or higher from the ground,
  • the cutting tool positions 100 mm to 300 mm high from the ground and,
  • the unguarded part of cutting tool is horizontally 750 mm or further away from the hanger.

After adjusting the hanger position, tighten the screw with a wrench or screwdriver (depending on the power unit) securely.

Adjusting the shoulder harness
For DUX18/UX01G Cordless multi function power head

WARNING: Do not use the tool if you cannot adjust the shoulder harness length within the range as illustrated. Using the tool with improper weight balance may bring the cutting tool upward and result in personal injury.
When replacing an accessory with another, the weight balance of the equipment may change. In such case, adjust the shoulder harness length as follows.
► Fig.18: 1. Hanger
Adjust the shoulder harness length so that:

  • the hanger positions 750 mm or higher from the ground,
  • the cutting tool positions 100 mm to 300 mm high from the ground and,
  • the unguarded part of cutting tool is horizontally 750 mm or further away from the hanger.

Using a nylon cutting head
During operation, use the tip of the nylon cutting cord for cut. As the nylon cutting cord is worn and shortened with the cutting operation, the operator needs to feed it manually. To feed the nylon cutting cord, tap the nylon cutting head against the ground while rotating.

NOTE: If the nylon cutting cord does not feed out, rewind it. Refer to the chapter “MAINTENANCE.”

MAINTENANCE

WARNING: Before inspecting or maintaining the equipment, switch off the motor and remove the spark plug cap or battery cartridge. Otherwise the cutting tool or other parts may move and result in serious injury.

WARNING: When inspecting or maintaining the equipment, always put it down. Assembling or adjusting the equipment in an upright position may result in serious injury.

WARNING: Follow the warnings and precautions in the chapter “SAFETY WARNINGS” and the instruction manual of the power unit.

NOTICE: Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result.
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.

Overall inspection

  • Tighten loose bolts, nuts and screws.
  • Check for damaged parts and blades. Ask our authorized service centre to replace them if necessary.

Rehappening the cutting tool

WARNING: Do not reshape cutting blades by yourself. Manual rehappening unbalances a cutting blade and it can cause vibrations and damage to the equipment.
Ask Makita authorized service centre to reshape and rebalance blunt cutter blades.

Lubricating moving parts
NOTICE: Follow the instruction of the frequency and amount of grease supplied. Otherwise insufficient lubrication may damage moving parts.

Gear case:
CAUTION: Do not apply grease when the gear case is hot. Hot gear case can cause burn injury.
Apply grease (Shell Alania 1 or 2, or equivalent) to the gear case through the grease hole approximately every 30 working hours.
► Fig.19: 1. Grease hole

Drive axle:
Apply grease (Shell Alania 1 or 2, or equivalent) to the drive axle approximately every 30 working hours.
► Fig.20
NOTE: Genuine Makita grease may be purchased from your local Makita dealer.

Replacing the nylon cord

WARNING: Use only the nylon cord with diameter specified in this instruction manual. Never use heavier line, metal wire, rope or the like. Failure to do so may cause damage to the tool and result in serious personal injury.
WARNING: Always remove the nylon cutting head from the tool when replacing the nylon cord.
WARNING: Make sure that the cover of the nylon cutting head is secured to the housing properly as described in this instruction manual. Failure to properly secure the cover may cause the nylon cutting head to fly apart resulting in serious personal injury.
Replace the nylon cord if it is not fed any more. The method of replacing the nylon cord varies depending on the type of the nylon cutting head.

96-M10L
► Fig.21

Replacing the plastic blade
Replace the blade if it is worn out or broken.
► Fig.22
When installing the plastic blade, align the direction of the arrow on the blade with that of the protector.

Storage
WARNING: Follow the warnings and precautions in the chapter “SAFETY WARNINGS” and the instruction manual of the power unit.
When storing the attachment separated from the power unit, put the cap onto the end of the shaft.
► Fig.23

Interval of inspection and maintenance

TROUBLESHOOTING

Before asking for repairs, conduct your own inspection first. If you find a problem that is not explained in the manual, do not attempt to dismantle the machine. Instead, ask Makita Authorized Service Centers, always using Makita replacement parts for repairs.

Makita Corporation
3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan
www.makita.com

885828B916
EN, PTBR, ES,
ZHCN, ZHTW, ID,
MS, VI, TH, FA, AR 20200730