Bosch D-tect 150 SV Professional Instructions

D-tect 150 SV Professional

Safety Notes

Read and observe all instructions. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

  • Have the measuring tool repaired only through qualified specialists using original spare parts. This ensures that the safety of the measuring tool is maintained.
  • Do not operate the measuring tool in explosive environments, such as in the presence of flammable liquids, gases or dusts. Sparks can be created in the measuring tool which may ignite the dust or fumes.
  • For technological reasons, the measuring tool cannot ensure 100 % certainty. To rule out hazards, safeguard yourself each time before drilling, sawing or routing in walls, ceilings or floors by means of other information sources, such as building plans, pictures from the construction phase, etc. Environmental influences, such as humidity or closeness to electrical devices, can influence the accuracy of the measuring tool. Surface quality and condition of the walls (e.g., moisture, metallic building materials, conductive wallpaper, insulation materials, tiles), as well as the amount, type, size and position of the objects, can lead to faulty measuring results.

Product Description and Specifications

Please unfold the fold-out page with the representation of the measuring tool and leave it unfolded while reading the operating instructions.

Intended Use
The measuring tool is intended for detecting objects in walls, ceilings and floors. Depending on material and condition of the structural surface, metal objects, wooden beams, plastic pipes, wiring and cables can be detected. For objects detected, the object depth to the surface of the object is determined.
The measuring tool complies with the limit values according to EN 302435. Based on this, it must be clarified whether the measuring tool may be used in, e.g., hospitals, nuclear power plants and in close vicinity to airports, or mobile phone stations.

Product Features

The numbering of the product features shown refers to the illustration of the measuring tool on the graphic page.

  1. Marking aid, top
  2. Wheel
  3. Marking aid, left and right
  4. Battery lid
  5. Latch of battery lid
  6. Handle
  7. Maintenance flap
  8. Serial number
  9. Sensor area
  10. Selection button, right
  11. Start button Start 
  12. Selection button, left
  13. Audio signal button
  14. Setup button Setup
  15. On/Off button
  16. Display
  17. LED
  18. Protective pouch

The accessories illustrated or described are not included as standard delivery.
Display Elements     

a Audio signal indicator
b Battery indicator
c Sensor-range indicator
d Area already detected
e Measuring scale for object depth
f Area not yet detected
g Outer edges, to be marked left and right via marking aid 3
h Operating-mode indication
i Black: Found object within the sensor range
j Grey: Found object outside of the sensor range
k Centre line, corresponds with the marking aid 1
l Indication of the object depth
m Indication of the object material
n “Live” wire indicator

Technical Data

Article number D-tect 150 SV
Professional
Universal Detector 3 601 K10 008
Measuring accuracy to the object
centre a2)		 ±5 mm1)
Accuracy of the displayed object
depth b2)
– in dry concrete
– in wet concrete		 ±5 mm1)
±10 mm1)
Minimum distance between two
neighbouring objects c2)		 4 cm1)
Operating temperature –10 … +50 °C
Storage temperature –20 … +70 °C
Batteries
Rechargeable batteries		 4×1.5VLR06(AA)
4 x 1.2 V HR06 (AA)
Operating life time, approx.
– Batteries (alkali-manganese)
– Rechargeable
batteries (2500 mAh)		 5h
7h
Degree of protection IP 54 (dust and splash
water protected)
Dimensions 22 x 9.7 x 12 cm
Weight according to
EPTA-Procedure 01/2003		 0.7 kg

1) Depending on size and type of object as well as material and condition of the base material
2) See graphic

  • In terms of accuracy, the measuring result can be inferior in case of unfavourable surface quality of the base material.

Please observe the article number on the type plate of your measuring tool. The trade names of the individual measuring tools may vary. The measuring tool can be clearly identified with the serial number 8 on the type plate.

Declaration of Conformity
We declare under our sole responsibility that the product described under “Technical Data” is in conformity with the following standards or standardization documents: EN 61010-1, EN 55022, EN 55024, EN 302435-1, EN 302435-2 according to the provisions of the directives 1999/5/EC, 2004/108/EC.

Dr. Egbert Schneider
Senior Vice President
Engineering

Dr. Eckerhard Strötgen
Head of Product
Certification

Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 19.05.2011

Assembly

Inserting/Replacing the Battery
To open the battery lid 4, press the latch 5 in the direction of the arrow and remove the battery lid. Insert the batteries/rechargeable batteries. When inserting, pay attention to the correct polarity according to the representation on the inside of the battery compartment.

The battery indicator b in the upper-status line on the display 16 indicates the charge condition of the batteries/rechargeable batteries.

Note: Pay attention to the changing battery symbol so that the batteries/rechargeable batteries are replaced in time.

When the “Please change batteries” warning indication is indicated on the display 16, the settings are saved and the measuring tool switches off automatically. Measurements are no longer possible. Change the batteries/rechargeable batteries.

To remove the batteries/rechargeable batteries, press on the rear end of a battery as indicated in the figure on the battery lid (1). The front end of the battery/rechargeable battery is released from the battery compartment (2), so that the battery/rechargeable battery can easily be removed.

Always replace all batteries/rechargeable batteries at the same time. Do not use different brands or types of batteries/ rechargeable batteries together.

  • Remove the batteries/rechargeable batteries from the measuring tool when not using it for longer periods. When storing for longer periods, the batteries/rechargeable batteries can corrode and discharge themselves.

Operation

  • Protect the measuring tool against moisture and direct sun light.
  • Do not subject the measuring tool to extreme temperatures or variations in temperature. In case of large variations in temperature, allow the measuring tool to adjust to the ambient temperature before switching it on. In case of extreme temperatures or variations in temperature, the accuracy of the measuring tool and the display indication can be impaired.
  • Do not attach any stickers or name-plates to the sensor area 9 on the back of the measuring tool. Especially metal name-plates affect the measuring results.
  • Use or operation of transmitting systems, such as WLAN, UMTS, radar, transmitter masts or microwaves, in the close proximity can influence the measuring function.

Method of Operation (see figure B)
The measuring tool checks the base material of sensor area 9 A in measurement direction A to the displayed measuring depth. Measurement is possible only during movement of the measuring tool in the direction of travel B and for a measuring distance of at least10 cm. Move the measuring tool in a straight line with light pressure over the wall so that the wheels remain in firm contact with the wall. Objects are detected that differ from the material of the wall. The object depth and, if possible, the object material, are indicated on the display. Optimum results are achieved when the measured distance is at least 40 cm and the measuring tool is moved slowly over the entire location to be checked. The tool’s method of operation ensures reliable detection of outer object edges that run transverse to the measuring tool’s movement direction.
Therefore, always move crossways over the area to be checked.

If several objects are located one over the other in the wall, the object that is indicated in the display is the one nearest to the surface.

The representation of the properties of detected objects in the display 16 can deviate from the actual object properties. This applies particularly for very thin objects, which are represented thicker in the display. Large cylindrical objects (e.g. plastic or water pipes) can appear in the display smaller than they actually are.

Detectable Objects­

  • Plastic pipes (e.g. water-carrying plastic pipes, as used in floor/wall-heating systems, with at least 10 mm in diameter; empty pipes with at least 20 mm in diameter)
  • Electrical wiring (independent of whether carrying voltage or not)
  • Three-phase mains wiring (e.g. to the stove) ­
  • Low-voltage wiring (e.g. for door bell, telephone ­
  • Metal pipes, bars, beams of any type (e.g. steel, copper, aluminium) ­
  • Reinforcing steel ­
  • Wooden beams ­
  • Hollow spaces

Measurements possible

  • In concrete/reinforced concrete ­
  • In brickwork (bricks, porous concrete, foam concrete, aerated concrete, lime-sand brick) ­
  • In light construction walls ­
  • Under surfaces such as stucco, tiles, wallpaper, parquet flooring, carpet ­
  • Behind wood, gypsum board

Special Measuring Cases
Based on the measuring priniciple, unfavourable conditions can influence the measuring result, for example:

  • Multi-layered walls ­
  • Empty plastic pipes and wood beams in hollow spaces and light construction walls ­
  • Objects running inclined in walls ­
  • Moist walls ­
  • Metal surfaces ­
  • Hollow spaces in a wall; these can be indicated as objects. ­
  • Closeness to equipment that generates strong magnetic or electromagnetic fields, e.g. radio base stations or generators.

Initial Operation

  • Protect the measuring tool against moisture and direct sun light.

Switching On and Off

  • Before switching the measuring tool on, make sure that the sensor area 9 is not moist. If required, dry the measuring tool using a soft cloth.
  • If the measuring tool was subject to an extreme temperature change, allow it to adjust to the ambient temperature before switching on.

Switching On ­

  • To switch on the measuring tool, press the On/Off button 15 or the start button 11. ­
  • LED 17 lights up green and the start display is indicated for 4 s on display 16. ­
  • When no measurement is carried out and no button is pressed for 5 minutes, the measuring tool switches off automatically. In the “Settings” menu, you can change the “Cut-off time” (see “Cut-off Time”, page 19).

Switching Off ­

  • To switch the measuring tool off, press the On/Off button 15. ­
  • When switching off the measuring tool, all settings are retained in the menus.

Switching the Audio Signal On/Off
The audio signal can be switched on/off with the audio signal button 13. In the “Settings” menu, you can select the type of signals in the “Tone signal” submenu (see “Tone Signals”, page 19).

Measuring Procedure

Switch the measuring tool on. The “standard start indication” appears on the display 16.

Position the measuring tool against the wall and move it over the wall in the direction of travel (see “Method of Operation”, page 16). Measured results are indicated on display 16 after a minimum measuring distance of 10 cm. To ensure correct measurement results, move the measuring tool slowly and completely over the assumed object in the wall.

If the measuring tool is lifted away from the wall during a measurement or not operated (moving the device or pressing a button) for more than 2 minutes, the last measured result remains on the display. “Hold” appears on the sensor-range indicator c. When the measuring tool is placed against the wall again, moved, or when the start button 11 is pressed, the measurement starts anew.

When LED 17 lights up red, an object is in the sensor range.
When LED 17 lights up green, no object is in the sensor range.
When LED 17 flashes, a “live” object is in the sensor range.

Display Elements (see figure A)
If an object is under the sensor, it will appear in the sensor range c of the display. Depending on size and depth of the object, identification of the material is possible. The object depth l to the upper edge of the found object is indicated in the status line.

Note: Both the indication of the object depth l as well as the material property m refer to the object pictured black in the sensor.

The indication of the object material m can represent the following characteristics:

Magnetic, e.g. reinforcing steel
Non-magnetic, but metal, e.g. copper pipe
Non-metal, e.g. wood or plastic
Material property unknown

The indication of “live” wires n can represent the following characteristics:

“Live”
Note: For “live” objects, no further characteristic is displayed.

­ Not definite whether “live” or voltage-free
Note: Three-phase mains wiring are possibly not detected as “live” conductors.

Localisation of Objects
To localise objects, moving over the measuring path once is sufficient. When no object has been found, repeat the motion perpendicular to the initial measuring direction (see “Method of Operation”, page 16). For precise localisation and marking of an object, move the measuring tool back over the measuring path.

When an object is indicated centrally below the centre line k in display 16, as in the example, you can mark it coarsely with the top marking aid 1. This mark, however, will only be precise, when the object is positioned exactly vertical in the wall, as the sensor range is located somewhat below the top marking aid.
For exact marking of the object on the wall, move the measuring tool left or right until the found object is positioned below one of the outer edges. When the found object, as an example, is indicated centrical below the dashed right-hand line g in display 16, you can mark it precisely with the right marking aid 3.

The direction of a found object in a wall can be determined by carrying out several offset measurements one after another (see figure I and “Examples for Measuring Results”, page 20). Mark and connect the respective measuring points.
By pressing the start button 11, the display of the objects found can be deleted at any time and a new measurement started.

  • Before drilling, sawing or routing into a wall, protect yourself against hazards by using other information sources. As the measuring results can be influenced through ambient conditions or the wall material, there may be a hazard even though the indicator does not indicate an object in the sensor range (no audio signal or beep and and the LED 17 lit green).

Changing the Operating Modes

Changing between different operating modes is possible with selection buttons 10 and 12.
­

  • Briefly press selection button 10 to select the next operating mode.
  • Briefly press selection button 12 to select the previous operating mode.

By selecting the operating modes, you can adapt the measuring tool to different wall materials. The current setting is always shown in the operating-mode indication h of the display.

Concrete Universal (preset)
The operating mode “Concrete Universal” is suitable for most applications in brickwork or concrete. Plastic and metal objects as well as electrical wiring are displayed. Hollow spaces in brickwork or empty plastic pipes with a diameter of less than 2 cm are possibly not displayed. The maximum measuring depth is 8 cm.

Concrete Wet
The operating mode “Concrete Wet” is particularly suitable for applications in wet concrete. Reinforcing steel, plastic and metal pipes, as well as electrical wiring are displayed. Differentiating between “live” and voltage-free conductors is not possible. The maximum detection depth is 6 cm.
Please observe that concrete requires several months to dry completely.

Concrete Special
The operating mode “Concrete Special” is particularly suitable for detecting objects embedded deep in reinforced concrete. Reinforcing steel, plastic and metal pipes, as well as electrical wiring are displayed. The maximum measuring depth is 15 cm.
When too many objects are displayed, it may be possible that you are moving directly alongside a reinforcement rod. In this case, place the measuring tool a few centimetres aside and try again.

Panel Heating
The operating mode “Panel Heating” is particularly suitable for detecting metal, metal-composite and water-filled plastic pipes, as well as for electrical wiring. Empty plastic pipes are not displayed. The maximum measuring depth is 8 cm.

Drywall
The operating mode “Drywall” is suitable for finding wooden beams, metal framing and electrical wiring in drywalls (wood, gypsum board, etc.). Filled plastic pipes and wooden beams are displayed identically. Empty plastic pipes are not detected. The maximum measuring depth is 8 cm.

Metal
The operating mode “Metal” is suitable for detecting metal objects and “live” conductors when other operating modes in different wall situations do not provide satisfactory results. In such cases, the detection results will be more extensive, yet less precise.

Signal View Mode
The operating mode “Signal View” is suitable for all materials. The signal strength at the corresponding detection position is displayed. In this operating mode, objects close to each other can be precisely detected and complicated material structures can be better evaluated based on the characteristic of the signal. The maximum detection depth is 6 cm.
The summit of the curve is displayed in the small scale above the operating-mode indication h in the form of a U. The object depth and the material properties (as far as possible) are displayed. The maximum measuring depth is 15 cm.

  • Conclusions on the object depth cannot be drawn from the signal strength.

Changing the Display Modes
Note: Changing the display modes is possible in any operating mode.
To switch from the standard start display to rule mode, press and hold selection button 10 or 12.
In the example, rule mode shows the same situation as in figure D: Three steel bars equally apart. In rule mode, the clearance between the detected object centres can be determined. The measuring distance covered from the starting point (in the example 20.1 cm) is displayed under the indication of the object depth l. The three objects are displayed as rectangles in the small rule above the operating-mode indication h. Note: Both the indication of the object depth l as well as the material property m refer to the object pictured black in the sensor. To return to the standard start display, briefly press selection button 10 or 12. Note: Only the display is reset, not the measuring mode!

“Settings” Menu
To access the “Settings” menu, press the setup button 14. To exit the menu, press the start button 11. The current settings are saved. The standard start display for the measuring process is activated.

Navigating in the Menu
Press the setup button 14 to scroll down. Press the selection buttons 10 and 12 to select the values: ­

  • Selection button 10 will select the right-hand or next value. ­
  • Selection button 12 will select the left-hand or previous value.

Language
In the “Language” menu, you can change the menu-guidance language. The default setting is “English”.

Cut-off Time
In the “Cut- off time” menu, you can set certain time intervals after which the measuring tool shall automatically shut off when no measurements are taken or settings are carried out. The default setting is “5 min”.

Light Duration
In the “Display illum.” menu, you can set a time interval, during which the display 16 shall be illuminated. The default setting is “30 sec”.

Brightness
In the “Brightness” menu, you can set the brightness of the display backlight. The default setting is “Max”.

Tone Signals
In the “Tone signal” menu, you can limit when the measuring tool shall give out an audio signal, provided that you have not switched off the signal with the audio signal button 13. ­

  • The default setting is “Wallobjects”: An audio signal sounds after each button press, and whenever a wall object is under the sensor range. Additionally, a short-beat warning signal is given for “live” wires. ­
  • With the adjustment “Live wire”, an audio signal sounds after each button press, as does the warning signal for “live” wires (short-beat signal) when the measuring tool indicates a power line. ­
  • With the adjustment “Keyclick”, an audio signal only sounds when pressing a button.

Default Mode
In the “Defaultmode” menu, you can set the default operating mode that is to be pre-set after switching the measuring tool on. The operating mode “Concrete Universal” is the default setting.

“Extended Settings” Menu
To access the “Extended settings” menu, press the setup button 14 and the On/Off button 15 at the same time when the measuring tool is switched off. To exit the menu, press the start button 11. The standard start display for the measuring process is activated and the settings are saved.

Navigating in the Menu
Press the setup button 14 to scroll down. Press the selection buttons 10 and 12 to select the values: ­ Selection button 10 will select the right-hand or next value. ­ Selection button 12 will select the left-hand or previous value.

Device Information
In the “Device Info” menu, information on the measuring tool is provided, e.g., about the “Operation Time”. In the “Restore Settings” menu, you can restore the factory settings.

Examples for Measuring Results
Note: In the following examples, the audio signal on the measuring tool is switched on.
Depending on the size and depth of the object under the sensor range, it is not always possible to positively determine whether this object is “live” or voltage-free. In this case, the  symbol will appear in indicator n.

“Live” Wire (see figure C)
A “live”, metal object (e. g. a power cable) is within the sensor range. The object depth is 1.5 cm. The measuring tool emits the warning signal for “live” conductors as soon as the power cable is detected by the sensor.

Steel Bar (see figure D)
A magnetic object (e.g. a steel bar) is within the sensor range. Further objects are also located to the left and right, outside of the sensor range. The object depth is 5.5 cm. The measuring tool emits an audio signal.

Copper Pipe (see figure E)
A metal object (e. g. a copper pipe) is within the sensor range. The object depth is 4 cm. The measuring tool emits an audio signal.

Plastic or Wooden Object (see figure F)
A non-metal object is within the sensor range. The object is plastic or wooden, and close to the surface. The measuring tool emits an audio signal.

Large Surface (see figure G)
A metal, large surface (e. g. a metal plate) is within the sensor range. The object depth is 2 cm. The measuring tool emits an audio signal.

Many Unclear Signals (see figures H­-I)
When many objects are shown in the standard start display, the wall probably consists of many hollow spaces. To broadly block out the hollow spaces, switch to the “Metal “operating mode. When there are still too many objects being shown, carry out several height-offset measurements and mark the detected objects on the wall. Offset marks are an indication for hollow spaces, whereas marks on a line indicate an object.

Troubleshooting ­ Causes and Corrective Measures

Error Cause Corrective Measure
Measuring tool cannot be switched on Batteries empty Replace batteries
Batteries incorrectly inserted (wrong polarity) Check if the batteries are inserted correctly
Measuring tool switched on but does not react Take out batteries and reinsert again
Measuring tool too warm or
too cold		 Wait until operating temperature range is reached
Display indication: “Slipping Wheel” Wheel losing contact with
the surface		 Press the start button 11 and take care that the
two bottom wheels have contact with the wall
while moving the measuring tool; in case of uneven
walls, position a thin piece of cardboard between
the wheels and the wall
Display indication: “Speeding” Measuring tool has been
moved to quickly		 Press the start button 11 and move measuring tool
slowly over the wall
“Temperature over range” Wait until operating temperature range is reached

“Temperature under range”		 Wait until operating temperature range is reached
“Strong radio signal detected” Measuring tool switches off automatically. If possible, eliminate the interfering radio waves,
e.g. WLAN, UMTS, radar, transmitter masts or
microwaves, then switch the measuring tool on
again.

Maintenance and Service

Maintenance and Cleaning

  • Check the measuring tool each time before use. In case of visible damage or loose components inside the measuring tool, safe function can no longer be ensured.

Keep the measuring tool clean and dry at all times to ensure proper and safe working.
Do not immerse the measuring tool in water or other fluids.
Wipe away debris or contamination with a dry, soft cloth. Do not use cleaning agents or solvents.
Pay attention that the maintenance flap 7 is always properly closed. The maintenance flap may only be opened by an authorised aftersales service centre for Bosch power tools.
If the measuring tool should fail despite the care taken in manufacturing and testing procedures, repair should be carried out by an authorised after-sales service centre for Bosch power tools. Do not open the measuring tool yourself.
In all correspondence and spare parts orders, please always include the 10-digit article number given on the type plate of the measuring tool.
Store and transport the measuring tool only in the supplied protective pouch.
In case of repairs, send in the measuring tool packed in its protective pouch 18.

After-sales Service and Customer Assistance
Our after-sales service responds to your questions concerning maintenance and repair of your product as well as spare parts. Exploded views and information on spare parts can also be found under: www.bosch-pt.com

Our customer service representatives can answer your questions concerning possible applications and adjustment of products and accessories.

Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Tel. Service: +44 (0844) 736 0109
Fax: +44 (0844) 736 0146 E-
Mail:

Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: +353 (01) 4 66 67 00
Fax: +353 (01) 4 66 68 88

Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd. Power Tools Locked Bag 66 Clayton South VIC 3169 Customer Contact Center Inside Australia:
Phone: +61 (01300) 307 044
Fax: +61 (01300) 307 045 Inside

New Zealand: Phone: +64 (0800) 543 353 Fax: +64 (0800) 428 570 Outside AU and NZ:
Phone: +61 (03) 9541 5555
www.bosch.com.au

Republic of South Africa Customer service Hotline: +27 (011) 6 51 96 00
Gauteng ­ BSC Service Centre 35 Roper Street, New Centre Johannesburg
Tel.: +27 (011) 4 93 93 75
Fax: +27 (011) 4 93 01 26
E-Mail:

KZN ­ BSC Service Centre Unit E, Almar Centre 143 Crompton Street Pinetown
Tel.: +27 (031) 7 01 21 20
Fax: +27 (031) 7 01 24 46
E-Mail:

Western Cape ­ BSC Service Centre Democracy Way, Prosperity Park Milnerton
Tel.: +27 (021) 5 51 25 77
Fax: +27 (021) 5 51 32 23
E-Mail: b

Bosch Headquarters Midrand, Gauteng T
el.: +27 (011) 6 51 96 00 Fax: +27 (011) 6 51 98 80
E-Mail:

People’s Republic of China China Mainland Bosch Power Tools (China) Co., Ltd. 567, Bin Kang Road Bin Jiang District 310052 Hangzhou, P.R.China Service Hotline: 400 826 8484 Fax: +86 571 8777 4502
E-Mail:
www.bosch-pt.com.cn

Bosch Power Tools

HK and Macau Special Administrative Regions Robert Bosch Hong Kong Co. Ltd. 21st Floor, 625 King’s Road North Point, Hong Kong Customer Service Hotline: +852 (21) 02 02 35
Fax: +852 (25) 90 97 62
E-Mail:
www.bosch-pt.com.hk

Indonesia
PT. Multi Mayaka Kawasan Industri Pulogadung Jalan Rawa Gelam III No. 2 Jakarta 13930 Indonesia
Tel.: +62 (21) 46 83 25 22 Fax: +62 (21) 46 82 86 45/68 23
E-Mail:
www.bosch-pt.co.id

Philippines
Robert Bosch, Inc. 28th Floor Fort Legend Towers, 3rd Avenue corner 31st Street, Fort Bonifacio Global City, 1634 Taguig City, Philippines
Tel.: +63 (2) 870 3871
Fax: +63 (2) 870 3870

www.bosch-pt.com.ph

Bosch Service Center: 9725-27 Kamagong Street San Antonio Village Makati City, Philippines
Tel.: +63 (2) 899 9091
Fax: +63 (2) 897 6432

Malaysia
Robert Bosch (S.E.A.) Pte. Ltd. No. 8A, Jalan 13/6 G.P.O. Box 10818 46200 Petaling Jaya Selangor, Malaysia
Tel.: +60 (3) 7966 3194 Fax: +60 (3) 7958 3838
Toll-Free: 1800 880 188
www.bosch-pt.com.my

Thailand
Robert Bosch Ltd. Liberty Square Building No. 287, 11 Floor Silom Road, Bangrak Bangkok 10500
Tel.: +66 (2) 6 31 18 79 ­ 18 88 (10 lines) Fax: +66 (2) 2 38 47 83 Robert Bosch Ltd., P. O. Box 2054 Bangkok 10501, Thailand
1 619 929 J48 | (1.7.11)

Bosch Service ­ Training Centre 2869-2869/1 Soi Ban Kluay Rama IV Road (near old Paknam Railway) Prakanong District 10110 Bangkok Thailand Tel.: +66 (2) 6 71 78 00 ­ 4
Fax: +66 (2) 2 49 42 96
Fax: +66 (2) 2 49 52 99

Singapore
Robert Bosch (SEA) Pte. Ltd. 11 Bishan Street 21 Singapore 573943
Tel.: +65 6571 2772 Fax: +65 6350 5315
Toll-Free: 1800 333 8333
www.bosch-pt.com.sg

Vietnam
Robert Bosch Vietnam Co. Ltd 10/F, 194 Golden Building 473 Dien Bien Phu Street Ward 25, Binh Thanh District 84 Ho Chi Minh City Vietnam Tel.: +84 (8) 6258 3690 ext. 413
Fax: +84 (8) 6258 3692

www.bosch-pt.com

Disposal
Measuring tools, accessories and packaging should be sorted for environmental-friendly recycling.
Do not dispose of measuring tools and batteries/rechargeable batteries into household waste!
Only for EC countries: According to the European Guideline 2002/96/EC, measuring tools that are no longer usable, and according to the European Guideline 2006/66/EC, defective or used battery packs/batteries, must be collected separately and disposed of in an environmentally correct manner.
Batteries no longer suitable for use can be directly returned at:

Great Britain
Robert Bosch Ltd. (B.S.C.) P.O. Box 98 Broadwater Park North Orbital Road Denham Uxbridge UB 9 5HJ
Tel. Service: +44 (0844) 736 0109
Fax: +44 (0844) 736 0146
E-Mail:
Subject to change without notice.
Bosch Power Tools

OBJ_BUCH-1478-001.book Page 1 Friday, July 1, 2011 10:17 AM

Robert Bosch GmbH
Power Tools Division
70745 Leinfelden-Echterdingen
Germany
www.bosch-pt.com
1 619 929 J48 (2011.07) T / 220 UNI

WallscaPnrnoefer sDs-iotencatl Setup