Philips HTL8162 2.1CH 160W Bluetooth Soundbar with Wireless Subwoofer User Manual

PHILIPS HTL8162 2.1CH 160W Bluetooth Soundbar with Wireless Subwoofer

General information

Safety instructions
Please read carefully the safety mark on the back side
This mark is intended to alert the user from the non isolated dangerous voltage within the constitute a risk of electric shock to persons.
This mark is intented to alert the user for important operating and servicing instruction.

Warnings

• Avoid sustained periods on high-volume use, and do not turn the volume to maximum level while using high output signal, such as Mobile Phone or DVD, etc., as this will cause distortion and may damage the loudspeaker cones.
• Plaese switch off the system from the wall socket when not in use.
• Do not open the cover or back panel to avoid electrical shock or any other accidents. No user-serviceable parts are inside.
• Only for indoor use.
• Plug the system to the AC outlet with the right voltage marked on the back panel of the Subwoofer and soundbar.
• The MAINS plug is used as the disconnect device, the disconnect device shall remain readily operable.
  The product shall not be exposed to dripping or splashing and that no objects filled with liquids,such as vases,shall be placed on the product.
  • Batteries shall not be exposed to excessive heat such as
  • Attention should be drawn to the environmental aspects of battery disposal.

Care and safety information
Avoid high temperatures, moisture, water and dust

• Apparatus should not be exposed to dripping or splashing of liquid.
• Do not place any source of danger on the Subwoofer,
• Do not install near heat sources.
  Do not block any ventilation opening
• Place the apparatus in a location with adequate ventilation to prevent internal heat build up. Allow at least 10cm (4 inches) of free space all around the apparatus for adequate ventilation.
• At high volume the back cover of Subwoofer becomes hot. Do not touch it.
  Care of the cabinet
• Use a soft cloth slightly moistened to clean the cabinet. Do not use a solution containing alcohol, spirits, ammonia or abrasives.

Accessories

Connections

Soundbar back panel

1. AC Power cord.
2. Input Connect to sound sources such as computer, CD player, MP3, etc.
3. Optical Input.
4. USB slot.
5. HDMI ARC Input.

Subwoofer back panel

5. AC IN: AC Power cord.
6. LED: Solid red when not connected, Solid blue when connected.
7. ON/OFF
To turn on the subwoofer for wireless pairing, To turn off the subwoofer.

Do NOT use USB for charging devices which can cause damage to your external devices.thank you.

Top panel operation

1. Power or standby mode.
2. SRC: Change the input mode: “bt” denotes Bluetooth Mode, “Hd” denotes HDMI ARC Mode, “OP” denotes Optical Mode, “AU” denotes Audio Mode, “Ud” denotes USB* mode.
3. Play/pause in USB*/BT mode.
4. Play the previous song in USB*/BT mode.
5. Play next song in USB*/BT mode.
6. Volume decrease.
7. Volume increase.

Remark:
In order not to disturb in the dark, the LED display of soundbar is set to be dim after 30 seconds if there is no operation, and display off after another 90 seconds.
You can press any button to resume.
AVAILABLE IF CONNECTED

Remote controls

1. Power ON or Standby mode.
2. PAIR:
   Turn both soundbar and subwoofer on, they will pair automatically.
   Suggest not to change the ID if speaker system is working fine.
   a. In case they don’t get paired, press “MUTE” and hold 5 seconds to reset, choose any mode and then short press “PAIR” continuously until “1d” show on display, switch the subwoofer off and red & blue light will flash
   alternately after restart, press “PAIR” to confirm the connection, the subwoofer LED will go to solid blue when successfully connected.
   b. How to change frequency ID: “CHxx” will show on display after long press “PAIR”, press again to select the ID, subwoofer blue LED will flash and stay solid blue once successfully paired.
3. MUTE: Turn volume off, short press again to activate.
4. VOL+: To increase the Volume by short or long press VOL+.
5. Play the previous song by pressing “ ” but not in audio mode.
6. Play/pause in USB*/BT mode and MUTE in audio mode.
7. Play next song by pressing “ ”, but not in audio mode.
8. VOL-: To decrease the Volume by short or long press VOL-.
9. BT: Bluetooth mode.
10. ARC: HDMI ARC mode.
11. OPT: Optical mode.
12. AUD: Audio input mode.
13. USB: USB* mode.
14. TONE: Press to adjust Bass&Treble settings by using VOL+/-buttons.
    Bass&Treble levels:-6(min)~+6(max).

Remark
In order not to disturb in the dark, the LED display of soundbar is set to be dim after 30 seconds if there is no operation, and display o after another 90 seconds.
You can press any button to resume.

Playing the speakers and subwoofer

System positioning
The subwoofer is recommended to be put
The soundbar is recommended to be put on the flat desktop to get a better acoustic effect.

Helpful Hint:
To avoid magnetic interference, do not position the speakers, too close to your TV.

Bluetooth Operating Instruction

1. Press SRC key from soundbar or remote control to Bluetooth mode;
2. When selecting the Bluetooth mode. “.” of “bt.” in display will start blinking and you will hear an audio tone which indicates Bluetooth pairing mode.
3. For pairing with mobile phone or other Bluetooth devices, search the device named “Philips HTL8162” and pair it. Once paired, “.” of “bt.” slowly flash and come up with another audio tone. “.” of “bt.” will stop flash when playing music.
4. Press and hold “ ” for 3 seconds from remote control in order to force disconnect the Bluetooth connection.

Note: While using Bluetooth, if external call comes, then speaker system goes in mute mode in order to protect privacy of mobile phone user. Operation resumes once the call is disconnected.

Troubleshooting

Warning 
Under no circumstances should you try to repair the system yourself, as this will invalidate the warranty.
below before taking the system for repair. If you are unable to remedy the problem by following hints mentioned in below table.

Warranty

This Philips soundbar is warranted against any defect due to defective materials or workmanship for 12 months
from the date of purchase, should a defect develop during the warranty, TPV Technology India Pvt. Ltd.,its authorized service center in India.

The warranty is not valid in case

1. Proof of purchase is not accompanied with this warranty card.
2. The warranty card is not completed immediately after purchase.
3. The apparatus is not used according to this user manual.
4. Defects are caused due to improper or reckless use.
5. Any repairs are done by persons other than Philips authorized service centre.
6. The serial number is tampered with.
7. Defects due to causes beyond control like lightning, abnormal voltage or while in transit to the purchaser’s residence.

All consumables and parts susceptbile to normal wear and tear are not covered under this warranty.
for detailed team and condition applicable please refer www.philiphs.com/support

Model No.               Product Sl. No.
Invoice Number               Date of Purchase: /
Customer’s Name and address:
PIN:

Always there to help you!
Visit us at www.support.philips.com
Helpline: 1800 425 6396
Email: [email protected]
(10 a.m. to 9 p.m. Mondays to Saturdays & 10 a.m. to 6 p.m. on Sundays)

Product specifications