D-Link DCS-4614EK/DCS-4618EK Vigilance Outdoor Dome Camera Installation Guide

Quick Installation Guide Vigilance Outdoor Dome Camera
DCS-4614EK
DCS-4618EK

Additional documentation is also available on the D-Link website

Before You Begin

This installation guide provides instructions for installing and configuring your camera.
Additional documentation is also available on the D-Link support website.
Refer to the manual for your model for additional information on how to configure the device using the associated Setup Wizard.
The manual and Setup Wizard may be found at https://dlink.com/support/.

Package Contents

This package includes the following items:

  • Vigilance Outdoor Dome Camera
  • Cable Waterproofing Connector
  • Mounting Kit
  • Allen Key
  • Alignment Sticker
  • Documentation

If any of the above items are damaged or missing, please contact your local D-Link reseller.
Note: Using a power supply with a different voltage than the one recommended for the device will cause damage and void the warranty for this product.

System Requirements

  • Computer running Microsoft Windows®
  • Internet Explorer 11

Hardware Overview

DCS-4614EK Front/Side

# Feature

Description

1 microSD  Slot Slot for a microSD card.
2 Vertical  Adjustment  Screw Loosen to adjust the vertical angle of the camera
3 IR LED Provides illumination for low-light environments
4 Light Sensor Monitors lighting conditions and switches between color and infrared accordingly
5 Horizontal  Adjustment  Screw Loosen to adjust the horizontal angle of the camera
6 Camera Lens Fixed camera lens

Table 1: Front View Descriptions

DCS-4618EK Front/Side

# Feature

Description

1 Vertical0  Adjustment  Screw Loosen to adjust the vertical angle of the camera.
2 IR LED Provides illumination for low-light environments
3 Camera Lens Motorized camera lens
4 microSD  Slot Slot for microSD card.
5 Light Sensor Monitors lighting conditions and switches between color and infrared accordingly

Table 2: Front View Descriptions

DCS-4614EK/DCS-4618EK Cable Interfaces

# Feature

Description

1 Ethernet  Jack RJ-45 connector for Ethernet. Can also, be used to power the camera using Power over Ethernet (PoE)
2 Power  Connector Connects to an optional 12V/ 1.5 A power adapter (not included)
3 Reset Button Press and hold for more than five seconds, then release to perform a factory reset

Management Options

To configure and manage your camera, it is recommended that you download the associated Setup Wizard and the D-ViewCam software suite, both of which are available from the D-Link website.
Installing the Setup Wizard

  1. Open a web browser, navigate to dlink.com/support/, and select your region.
  2. On the next screen, enter the model number of your camera in the search bar and click Search. Click the picture of your camera. On the product page, click The download button is next to Setup Wizard.
  3. Once the executable file has finished downloading, click it and follow the instructions to install the Setup Wizard.

Configuring the Camera

  1. Ensure that your camera is plugged in (either using a 12 V 1.5 A power adapter or a PoE-enabled device) and connected to your computer with an Ethernet cable.
  2. Open the Setup Wizard. It will display the MAC address and IP address of your camera. If you have a DHCP server on your network, this will be a dynamic IP address.
    If your network does not use a DHCP server, the network camera’s default static IP 192.168.0.20 will be displayed. Select your camera, then click the Link button to continue.
  3. If this is your first time logging in, you will be prompted to create a password, which must be between 8 and 30 characters and must contain both letters and numbers. Press OK.
  4. To view the camera display, on the main screen of the Setup Wizard, click the Search button, then select your camera and click the Link button to open the camera’s web UI. Alternatively, open a web browser and type the camera’s IP address (displayed in step 2) into the URL bar, and press Enter. Enter the password you created, and click Login to continue.

Installing D-ViewCam

  1. Open a web browser, navigate to dlink.com/support/, and select your region.
  2. On the next screen, click the D-ViewCam link and click the most recent version to download the D-ViewCam setup wizard (packaged as a zip file).
  3. Once the file has finished downloading, unzip it, and click the executable file SetupTool.exe. Follow the instructions to install the D-ViewCam software suite.

For advanced viewing options, refer to the D-ViewCam User Manual.

Mounting the Camera

Note: It is highly recommended that you configure and test your camera before mounting it.
The DCS-4614EK and DCS-4618EK can be installed on the ceiling or wall. The process is identical for both cameras.
Mounting the Camera

  1. Use the included T10 or T15 screwdriver to unscrew the three screws on the dome cover and remove it.
  2. Press the sides of the plastic lining and gently lift it to remove the lining from the camera.
  3. Place the installation sticker on the ceiling or wall. Using a 4 mm drill bit, drill three holes 30 mm deep into the wall or ceiling.
    Drive the plastic wall anchors into the holes.
  4. Insert three mounting screws into the holes in the base of the device. Place the device against the mounting sticker and screw it in to attach it to the wall or ceiling.
  5. Reattach the lining to the camera body by sliding it on until it clicks. Replace the dome cover and refasten the screws securing it in place.

Adjusting the Lens
The angle, zoom, and focus of the lens can be adjusted using the web UI. For information on how to do this, refer to the User Manual.

Waterproofing Your Installation
To waterproof your camera, follow the instructions below. A round Ethernet cable, a crimping tool, and RJ-45 plugs are required for this procedure.

  1. Place the washer around the base of the Ethernet connector as shown.
  2. Thread the bare Ethernet cable through the waterproof connector as shown.
  3. Attach an RJ-45 plug to the end of the cable using a crimping tool.
  4. Connect the RJ-45 plug into the Ethernet connector, then screw the waterproof connector to the Ethernet connector by turning it clockwise about one half-turn.
  5. Screw the back part of the waterproof connector clockwise until there is a tight seal around the Ethernet cable.
  6. The power connector and reset button cables are not waterproof. It is recommended to use waterproof tape to protect them. Wind the tape around each cable in an overlapping manner to cover them.

Additional Information

If you are encountering problems setting up your network, please refer to the user manual.
Additional help is available online. To find out more about D-Link products or marketing information, please visit the D-Link support website at http://dlink.com/support/.

Warranty Information

Please visit http://warranty.dlink.com/ for warranty information for your region.

Regulatory Statements (Only for Class A product)

Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Non-modification Statement
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Caution
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

Innovation, Science and Economic Development Canada (ISED) Statement:
This Class A digital apparatus complies with Canadian ICES-003.
CE EMI Class A Warning
This equipment is compliant with Class A of CISPR 32. In a residential environment, this equipment may cause radio interference.

CE EMI CLASS A WARNING

This equipment is compliant with Class A of CISPR 32. In a residential environment, this equipment may cause radio interference.

SAFETY INSTRUCTIONS

The following general safety guidelines are provided to help ensure your own personal safety and protect your product from potential damage. Remember to consult the product user instructions for more details.

  • Static electricity can be harmful to electronic components. Discharge static electricity from your body (i.e. touching grounded bare metal) before touching the product.
  • Do not attempt to service the product and never disassemble the product. For some products with a user-replaceable battery, please read and follow the instructions in the user manual.
  • Do not spill food or liquid on your product and never push any objects into the openings of your product.
  • Do not use this product near water, areas with high humidity, or condensation unless the product is specifically rated for outdoor application.
  • Keep the product away from radiators and other heat sources.
  • Always unplug the product from mains power before cleaning and use a dry lint-free cloth only.

DISPOSING AND RECYCLING YOUR PRODUCT

This symbol on the product or packaging means that according to local laws and regulations this product should be not be disposed of in the household waste but sent for recycling. Please take it to a collection point designated by your local authorities once it has reached the end of its life, some will accept products for free.
By recycling the product and its packaging in this manner you help to conserve the environment and protect human health.

GPL Code Statement
This D-Link product includes software code developed by third parties, including software code subject to the GNU General Public License (“GPL”) or GNU Lesser General Public License (“LGPL”). As applicable, the terms of the GPL and LGPL, and information on obtaining access to the GPL code and LGPL Code used in this product, are available to view the full GPL Code Statement at: https://tsd.dlink.com.tw/GPL
The GPL Code and LGPL Code used in this product are distributed WITHOUT ANY WARRANTY and are subject to the copyrights of one or more authors. For details, see the GPL code and the LGPL code for this product and the terms of the GPL and LGPL. Please take it to a collection point designated by your local authorities once it has reached the end of its life, some will accept products for free. By recycling the product and its packaging in this manner you help to conserve the environment and protect human health.
Written Offer for GPL and LGPL Source Code Where such specific license terms entitle you to the source code of such software, D-Link will provide upon written request via email and/or traditional paper mail the applicable GPL and LGPL source code files via CD-ROM for a nominal cost to cover shipping and media charges as allowed under the GPL and LGPL.
Please direct all inquiries to:
Email:

Snail Mail:
Attn: GPLSOURCE REQUEST
D-Link Systems, Inc.
17595 Mt. Herrmann Street
Fountain Valley, CA 92708

Notes

TECHNICAL SUPPORT
dlink.com/support
Ver. 1.00(WW)_90x130
2020/11/09
101-010-0198-01