LG SN5R Wireless Sound Bar Owner’s Manual

LG SN5R Wireless Sound Bar Owner’s Manual

Wireless Sound Bar

Please read this manual carefully before operating your set and retain it for future reference.
To view the instructions of advanced features, visit http://www.lg.com and then download Owner’s Manual. Some of the content in this manual may differ from your unit.

Front Panel

The buttons are located on the side.

 (Standby) · · · · · · · · · Switches the unit ON or OFF.
F (Function) · · · · · · · · · · · · · · · · · · · · · · · Selects function.
-/+ (Volume) · · · · · · · · · · · · · · · · · · · · Adjusts volume

Rear Panel

DC IN · · · · · · · · · · · · · · · · · · · · · Connect to the AC adapter.
OPTICAL IN · · · · · · · · · · · Connect to an optical device.
HDMI IN · · · · · · · · · Connect to device with HDMI OUT.
HDMI OUT (TV ARC) · · · · · · · · · · · · · · · Connect to a TV.
USB (Service only) · · · · · · · · · S/W download connector

 Make sure to properly align and connect the optical cable; improper alignment may cause damage to the jack.

Subwoofer Connection

Place the wireless subwoofer near the sound bar and follow steps below.

  1. Connect the power cord of the sound bar and the wireless subwoofer to the outlet.
  2. Turn on the sound bar.
    • The sound bar and wireless subwoofer will be automatically connected. The subwoofer’s green LED turns on.

Manual Subwoofer Connection

If the subwoofer does not make sound, try to connect manually.

  1. Press PAIRING on the rear of the wireless subwoofer.
    • The green LED on the rear of the wireless subwoofer blinks quickly. (If the green LED does not blink, press and hold the PAIRING.)
  2. Turn on the sound bar.
    • Pairing is completed. The green LED on the rear of the wireless subwoofer turns on.

 Keep the sound bar and the subwoofer away from the device (ex. wireless router, microwave oven, etc.) over 1 m to prevent wireless interference.

TV Connection

Connect the sound bar and TV using Optical (A ) or HDMI ARC (B ).

A: Optical Connection

  1. Connect the sound bar to the TV using Optical cable.
  2. Set up [External Speaker (Optical)] on your TV setting menu.

B: HDMI (ARC) Connection

  1. Connect the sound bar to the TV using HDMI cable.
  2. Set up [External Speaker (HDMI ARC)] on your TV setting menu.

  • HDMI connection is unavailable if your TV does not support HDMI ARC.
  • If this unit is connected by OPTICAL and ARC at the same time, the ARC signal has a higher priority.

Additional Device Connection

  1. Connect to the external device like as follow.
  2. Set the input source by pressing F repeatedly.

Remote control

Replacement of Battery

 : Skip
 : Play/Pause

  • Bluetooth connection lock (BT LOCK): Select the Bluetooth function by pressing F repeatedly. Long press and press it again to limit Bluetooth connection to only BT and LG TV.
    SOUND EFFECT: Selects a sound effect mode.
  •  TV remote: Long press SOUND EFFECT and press it again to use TV remote control.
     :Turns on or off the Night time mode.
     : Displays the information of a file, an input source or connected Bluetooth device name.
  • Auto Power ON/OFF: Long press  and press it again.
     : Adjusts sound level of each speaker
  • – Surround sound: Long press  and press it again.
    * : This button is not available.

Additional Information

Specification
Power consumption Refer to the main label.
Networked standby : 1.0 W (If all  etwork ports are activated.)
AC adapter
  • Model : DA-50F25
  • Manufacturer : Asian Power Devices Inc.
  • Input : 100 – 240 V ~ 50 – 60 Hz
  • Output : 25 V 2 A
  • Model : MS-Z2000R250- 050D0-P
  • Manufacturer : MOSO POWER SUPPLY TECHNOLOGY CO., LTD.
  • Input : 100 – 240 V ~ 50/60 Hz
  • Output : 25 V  2 A
Dimensions (W x H x D) Approx.
890.0 mm X 57.0 mm X
85.0 mm With foot
Amplifier (Total RMS Output power) 520 W RMS

Design and specifications are subject to change without notice.

Rear Surround sound
Wireless Rear Speakers Kit included for real surround sound. (SPJ4-S)

How to disconnect the wireless network connection or the wireless device
Set up the AUTO POWER ON/OFF function to off and turn off the unit.

OPEN SOURCE SOFTWARE NOTICE INFORMATION

To obtain the source code under GPL, LGPL, MPL, and other open source licenses, that is contained in this product, please visit http://opensource.lge.com. In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download.

LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping, and handling) upon email request to .

This offer is valid for a period of three years after our last shipment of this product. This offer is valid to anyone in receipt of this information.

Declaration of Conformity

Hereby, LG Electronics declares that the radio equipment type Wireless Sound Bar is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:
http://www.lg.com/global/support/cedoc/cedoc# For consideration of the user, this device should be installed and operated with a minimum distance of 20 cm between the device and the body.

Wireless Rear Speakers Kit (Receiver)

Please read this manual carefully before operating your set and retain it for future reference.
To view the instructions of advanced features, visit http://www.lg.com and then download Owner’s Manual. Some of the content in this manual may differ from your unit.

Rear Speakers Connection

 Speaker design and connection method may be different according to models.

  1. Connect the speaker cables to rear speakers correctly.
  2. Connect the Wireless Receiver and the rear speakers (Blue: left, Grey: right) with the speaker cables.
  3. Turn on the Surrond function to enjoy surround sound.

Wireless Receiver Connection

  1. Connect the power cord of wireless receiver to the outlet.
  2. Turn on the unit: The unit and wireless receiver will be automatically connected. The receiver’s yellow – green LED turns on.

Wireless Receiver Connection Manually

If the rear speakers do not make sound, try to connect manually.

  1. Press PAIRING button on the rear of the wireless receiver.
    • The yellow – green LED on the wireless receiver blinks quickly.
  2. Turn on the main unit.
  3. Pairing is completed.
    • The yellow – green LED on the wireless receiver turns on.

 Set the distance between the sound bar and the wireless receiver as close as possible and keep them away from the device (ex. wireless router, microwave oven, etc.) over 1 m to prevent wireless interference.

Surround Sound On/Off

When you turn on surround function, you can enjoy magnificent surround sound for all the input sound source with rear speakers.

 The initial setting for the surround function is OFF, turn the surround function ON to use it.

Surround On: Press and hold button on the remote control about 3 seconds and then press button repeateadly to select ON – SURROUND in the display window.

Surround Off: Press and hold button on the remote control about 3 seconds and then press button repeateadly to select OFF – SURROUND in the display window.

Additional Information

Specification of Wireless reciever
Power requirement Refer to the main label on the wireless receiver
Power consumption Refer to the main label on the wireless receiver.
Dimensions (W x H x D) Approx. 60 mm x 220 mm x 175 mm
Design and specifications are subject to change without notice.

About Ferrite Core (Optional)

Declaration of Conformity

Hereby, LG Electronics declares that the radio equipment type Receiver is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.lg.com/global/support/cedoc/cedoc#

For consideration of the user, this device should be installed and operated with a minimum distance of 20 cm between the device and the body.