GRUNDIG SCN 230 Negro Clock Radio User Manual

Clock Radio
User Manual

SCN 230
SCC 240

01M-GCR1030-4620-03
01M-8870391600-4620-03
01M-GCR1040-4620-03
01M-8870401600-4620-03

SETUP AND SAFETY

This device is designed for the playback of audio signals. Any other use is expressly prohibited.
Protect the device from moisture (water drops or splashes). Do not place any vessels such as vases on the device. These may be knocked over and spill fluid on the electrical components, thus presenting a safety risk.
Do not place any naked flames such as candles on the device.
Thunderstorms are a danger to all electrical devices. Even if the device is switched off, it can be damaged by a lightning strike to the main cable. Always disconnect the main cable during a storm.
If malfunctions occur due to static electricity charges or brief mains voltage surges, reset the device. To do this, pull out the mains adapter and connect it again after a few seconds.
Make sure the device is adequately ventilated. Do not cover the ventilation slots with newspapers, table cloths, curtains, etc.
When deciding where to place the device, please note that furniture surfaces are covered by various types of varnish and plastic, most of which contain chemical additives. These additives can corrode the device supports, leaving residues on the furniture surfaces which can be difficult or impossible to remove.
Only use the device in a moderate climate.
Do not use any cleaning agent, as this may damage the casing. Clean the device with a clean, moist leather cloth.
Do not expose the backup battery to extreme heat, caused for example by direct sunlight, heaters, or fire.
Never open the device casing. No warranty claims are accepted for damage caused by incorrect handling.
The type plate is located on the bottom of the device.
Do not expose the device to extreme heat, caused for example by direct sunlight, heater fire.

Compliance with the WEEE Directive and Disposing of the Waste Product:
This product complies with EU WEEE Directive (2012/19/EU). This product bears a classification symbol for waste electrical and electronic equipment (WEEE).
This symbol indicates that this product shall not be disposed of with other household wastes at the end of its service life. Used devices must be returned to an official collection point for the recycling of electrical and electronic devices. To find these collection sys-tems please contact your local authorities or re-tailer where the product was purchased. Each household performs an important role in recovering and recycling old appliances. Appropriate disposal of used appliances helps prevent potential negative consequences for the environment and human health.

Compliance with RoHS Directive
The product you have purchased complies with EU RoHS Directive (2011/65/EU). It does not contain harmful and prohibited materials specified in the Directive.
Package information
Packaging materials of the product armanufactured from recyclable materials in accordance with our National Environment Regulations. Do not dispose of the packaging materials together with the domestic or other wastes. Take them to the packaging material collection points designated by the local authorities.

This device is noise-suppressed according to the applicable EU directives. This product fulfils the European directives 2014/53/EU, 2009/125/EC and 2011/65/EU. You can find the CE declaration of conformity for the device in the form of a pdf file on the Grundig Homepage www.grundig.com/downloads/doc
SCN 230 Power supply:
Manufacturer of AC Adaptor: Dongguan Turnmax Electronic Co., Ltd.
Adress: Erxiafang Industrial Zone, Xiansha, Gabou Town, Dongguan, Guangdong Province 523287P.R. China
Model: TM-K006VA-00501000PE-02
AC Adaptor Input: 100 – 240V~ 50/60 Hz 0.2A;
Output: 5V 1.0A 5.0W
Average active efficiency: 73,62%
No-load power consumption: <0.1 W
Max. Power consumption:
<4.5W (operation)
<1W (standby)

SCC 240 Power supply:
Manufacturer of AC Adaptor: Dongguan Turnmax Electronic Co., Ltd.
Adress: Erxiafang Industrial Zone, Xiansha, Gabou Town, Dongguan, Guangdong Province 523287P.R. China
Model: TM-K007VC-00501500PE-02
AC Adaptor Input:100 – 240V~, 50/60 Hz 0.25A;
Output: 5V 1.5A 7.5W
Average active efficiency: 76,65%
No-load power consumption: <0.1W
Max. Power consumption:
<11 W (operation)
<1W (standby)

Output:
USB host (For SCC 240 only):
5V 1A charge out

Back up micro batteries:
Back up DC Batt: 2 x 1.5v UM4/R03/AAA

Frequency bands:
FM 87.5 …108.0 MHz
BT frequency: 2402-2480MHz (for SCC 240)
BT maximum transmitted power: 4dBm (for SCC 240)

Circuit features:
Loudspeaker: 2 – 1/4 inch
Output Power: 1.5 W
Dimensions:
W x H x L 117 x 104 x 90 mm
Weight: 300 gr

Technical and design modifications reserved.

POWER SUPPLY

Mains operation
Check that the mains voltage on the type plate (on the bottom of the device) corresponds to your local mains supply. If this is not the case, contact your specialist dealer.

Plug the power adaptor into the socket (100 – 240V~, 50/60 Hz).

Caution:

The device is connected to the mains with the power plug. To fully disconnect the device from the mains, pull out the plug.
The main plug is used to disconnect the device. It shall remain readily operable and should not be obstructed during intended use.

Inserting the backup battery
The backup batteries ensure that the stored set¬tings are not lost in the case of a power failure.

Open the battery compartment by pressing the area market and pushing down the cover.
Observe the polarity marked on the base of the battery compartment when inserting the batteries (micro-batteries, 2 x 1.5 V, R03/ UM 4/ AAA).
Close the battery compartment.
Note:
▪ Remove the backup battery when it is flat or when you know that the device will not be used for a long period of time.

Environmental note:
▪ Batteries, including those which do not contain heavy metal, should not be disposed of with household waste. Always dispose of used batteries in accordance with local environmental regulations.

RADIO MODE

Antenna
For the best FM (UHF) reception it is sufficient to align the wire antenna accordingly.

Switching on and off

Switching the device from standby with the »ON/OFF« button.
Switch the device to standby with the »ON/OFF« button.

Searching for and saving radio stations – automatically
You can store 10 radio stations on presets.

Activate the station search by pressing the »TUNING+/HR« or »TUNING-/MIN« buttons until the frequency display changes to rapid run-through. The search stops when a station is found.
Note:
▪ To move the frequency forward in steps, briefly press »TUNING+/HR« or »TUNING-/MIN« several times.
Press and hold the »PRESET« button to activate the memory function.
Press the »TUNING+/HR« or »TUNING-/MIN« buttons to select the preset.
Press the »PRESET« button to save the station.
Note:
▪ If the stations are already stored on the presets, they are overwritten when new stations are stored.
To store more stations, repeat the steps 1 to 4.

Selecting stored stations

Select the preset by pressing the »PRESET« button to select the preset stations one after another.

Adjusting the volume

Adjust the volume with the »VOLUME -/AL 1« or »VOLUME +/AL 2« buttons.

Setting the brightness of the display

Press the »SLEEP/SNOOZE/DIMMER« button to adjust brightness levels in high, middle, and low levels.

BLUETOOTH MODE (SCC 240)

Connect to a mobile device with Bluetooth

Switching the device from standby with the »ON/OFF« button.
Press the »MODE/TIME« button repeatedly until »bt « is shown on display;
»bt « will be flashing on LCD;
Go to your mobile device, and find the “Sonoclock SCC 240” from the available Bluetooth device list. Then press to connect to the radio.
When SCC 240 has been connected to the mobile device, the »bt « will stop flashing.

Playback control via Bluetooth

Press the »ON/OFF« button to switch on the radio.
Connect the SCC 240 to a mobile device via Bluetooth.
Press the »PRESET« button to toggle the music playback in between play or pause status.
Press the »TUNING-/MIN« button to skip back to previously played songs.
Press the »TUNING+/HR« button to skip to the next songs.

Pairing mode

Press the »ON/OFF« button to switch on the radio;
If the SCC 240 is connecting to any mobile device via Bluetooth, press and hold the »PRESET«button to disconnect the current Bluetooth connection.
The SCC 240 will be in Bluetooth pairing mode by flashing the Bluetooth icon.
You can repeat the steps in “Connect to a mobile device with Bluetooth” for a new Bluetooth connection.

Adjusting the volume
1 Adjust the volume with the »VOLUME -/AL 1« or »VOLUME +/AL 2« buttons.
Power saving in Bluetooth
If there is no Bluetooth connection from the radio to any mobile device, the SCC 240 will switch to standby mode after 15 minutes.

TIMER MODE

Setting the time

Switching the device to standby with the »ON/OFF« button.
Press and hold the »TIME/MODE« button for two seconds to activate the setting. The current day of the week will be flashing on the LCD. »d1« is Monday, and »d7« is Sunday.
Then press the »TIME/MODE« button again for setting the current time.
Press »TUNING-/MIN« to set the minutes;
Press »TUNING+/HR« to set the hours;
Press the »TIME/MODE« button again to confirm the settings.

Setting the alarm time

Switch the device to standby with the »ON/OFF« button;
Press and hold the »VOLUME -/AL 1« button for alarm 1 or »VOLUME +/AL 2« for alarm 2;
For example, press and hold the »VOLUME -/AL 1« button to Then the alarm days will be flashing on the LCD (1 – 7, 1 – 5, or 6 – 7).
▪ Descriptions of alarm days are as follows:
1 – 7 (Alarm is active during the week)
1 – 5 (Alarm is active on weekdays)
6 – 7 (Alarm is active at the weekend)
Press the »TUNING-/MIN« or »TUNING+/HR« buttons to adjust the alarm days.
Press the »VOLUME -/AL 1« button to confirm;
Press the »TUNING-/MIN« button to set the alarm minutes;
Press the »TUNING+/HR« button to set the alarm hours;
Press the »VOLUME -/AL 1« button to finish the alarm 1 settings.
Note:
▪ The device wakes you up at the set alarm time, the alarm duration is 60 minutes.

Interrupting the alarm
▪ Press the »SLEEP/SNOOZE/DIMMER« while the alarm is sounding.
Note:
▪ The alarm signal will be stopped, and the alarm will be sounded again after nine minutes.

Canceling the alarm
1 Press »ON/OFF« while the alarm is sounding.
Note:
▪ The alarm will be sounded again at the next set alarm time.
Activating and deactivating the alarm

In standby mode, press the »VOLUME -/AL 1« or »VOLUME +/AL 2« button to activate the alarm with the last used alarm settings.
For example, if pressed »VOLUME -/AL 1« button, the last used alarm time would be displayed;
By repeatedly pressing the »VOLUME -/AL 1« button, the radio will display the last set alarm time, the » « and the » « icons.

Sleep timer

Press and hold the »SLEEP/SNOOZE/DIMMER« button for about 2 seconds to activate the sleep timer.
Then repeatedly press the »SLEEP/SNOOZE/DIMMER« button to select the auto switch-off timer from 90 minutes to 10 minutes.
To switch off the sleep timer before the set time press and hold the »SLEEP/SNOOZE/DIMMER« button for about 2 seconds, then repeatedly press the button again until »OFF« is displayed.

Charging a mobile phone (For Grundig SCC 240 only)
The USB socket on the backside can provide DC power of 5V for charging a mobile phone. Connect the mobile phone to the USB socket with an appropriate cable. The USB power is available in all the operating modes and including standby mode. Refer to the user manual or the manufacturer of the mobile phone to verify if it supports charging from USB power. The USB socket is suitable for DC power-out only and cannot be used for e.g. playback of music from a USB stick.

Beko Grundig Deutschland GmbH
Thomas-Edison-Platz 3
D-63263 Neu-Isenburg
www.grundig.com

Download

GRUNDIG SCN 230 Negro Clock Radio User Manual

Was this manual helpful?